Avenview HBT-C6POE-HDV-S Instruction Manual

VIDEO WALL VIDEO PROCESSORS MULTIVIEWERS DIGITAL SIGNAGE EXTENDERS CONTROL CENTERS SCALERS WIRELESS HDBaseT HDMI/VGA Scaler Over CAT5e/6/7 Transmitter with LAN Support © 2015 Avenview Inc. All rights reserved. The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any express or implied warranty, relating to its products are is strictly prohibited. Model #: HBT-C6POE-HDV-S

www.avenview.com Product Application & Market Sectors

1. GETTING STARTED...........................................................................................................................1 mortantaegards. aetnstrctions. egatoroticesFederaommnicationsommissionF. 2. ntrodction. INTRODUCTION ........................... ..................................................................................................3 Pa cage ontents ......................................................................................................................4 eorensta atio n ....................................................................................................................4 LPF. 7.3 REMOTE CONTROL .....................................................................................................................8 PPL. 8. RS-232 PIN DEFINITIONS ....................................................................................................................9 PLP. 9. RS-232 COMMANDS..... .......................................................................................................................10PUPLKacPane. ...........................................................................................................................................12PUPLKFront Pane. nstaationK. LUL. 11. INPUT RESOLUTION SUPPORT..........................................................................................................14 eciications. 3. FEATURES ....................................... ...................................................................................................3 6. APPLICATION DIAGRAM ...................................................................................................................5 7. PANEL DESCRIPTION ...................................................................................................................6 7.1 INPUT PANEL (FRONT PANEL) .................................................................................................6 7.2 INPUT PANEL (REAR PANEL) .................................................................................................7 12. INSTALLATION ....................................................................................................................................15 13. GENERAL TROUBLESHOOTING .......................................................................................................15 14. SPECIFICATIONS .................................................................................................................................16 1.2 SAFETY INSTRUCTIONS ..................................................................................................................1 1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................... 2 1.1 IMPORTANT SAFEGUARDS ..............................................................................................................1

orta ntaeg ards Please read all of these instructions carefully before you use the device. Save this manual for future reference. What the warranty does not cover •• Any product, on which the serial number has been defaced, modified or removed. •• Damage, deterioration or malfunction resulting from: •• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. •• Repair or attempted repair by anyone not authorized by us. •• Any damage of the product due to shipment. •• Removal or installation of the product. •• External causes to the product, such as electric power fluctuation or failure. •• U se of supplies or parts not meeting our specifications. •• Normal wear and tear. •• Any other causes which does not relate to a product defect. •• Removal, installation, and set-up service charges. aetnstr ctio nsKPK The HBT-C6POE-HDV-S has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the HBT-C6POE-HDV-S should be used with care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. ! Do not dismantle the housing or modify the module. ! Dismantling the housing or modifying the module may result in electrical shock or burn. ! Refer all servicing to qualified service personnel. ! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage or other hazards ! Keep the module away from liquids. ! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately. ! Have the module checked by a qualified service engineer before using it again. ! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. Warning symbols DescriptionLYUPPLPPUPPLPLLPYULLLKU ONLY USE THE PROVIDED POWER CABLE OR POWER ADAPTER SUPPLIED. DO NOT TAMPER WITH THE ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL SHOCK OR BURN. PULLYUUF DO NOT TAMPER WITH THE UNIT. DOING SO WILL VOID THE WARRANTY AND CONTINUED USE OF THE PRODUCT. PUYPLUFKULLUFULU THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC. PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT

scaling and switching any video along with audio and extending the uncompressed digital signal over CAT5e/6/7 cable to the Receiver at a distance of up to 100 meters. This unit can alsosupport 2-way IR, RS-232 and bidirectional LAN support. The user can simply control many functions via on-panel buttons or IR remote control with support of an On-screen Display (OSD) providing selection and system information. The HBT-C6POE-HDV-S provides a full range of output resolutions, from 640 up to 1080p and WUXGA (RB). The bi-directional Power over Ethernet (PoE) function provides greater flexibility during installations.KKULPKPKKYPUPUUPLKK-UK-UK--KK--P-UKKL-KKPU-KK-KK • Supports both HDMI/VGA inputs scaling to a full range of HDTV or PC resolutions up to 1080p and WUXGA (RB). • Transmission of uncompressed data over a single CAT5e/6/7 cable up to 100m/328ft. • 5Play™ convergence: Video and Audio, LAN serving, bidirectional Power over Ethernet (PoE) and Control (IR RS-232 bypass). • Supports IR, Remote control, RS-232 (bypass) and on-panel controls. • Provides bidirectional 24V DC power to or receive from compatible PoE Receiver through CAT5e/6/7 cable. • Supports Ethernet transmission rates up to 100 Mbps. • Supports NTSC and PAL formats for Composite Video input. Note: 1. This system was tested with CAT6/23AWG cables, results may vary with cables of different specifications. 2. The PoE function is designed for powering compatible Receiver units only—non-PoE Receivers will need their own power supply. Receivers from other brands may not be compatible. 3. DO NOT connect the LAN connection to the CAT5e/6/7 port. Doing so may cause a power shutdown and may damage the device. 3. FEATURES

1 HBT-C6POE-HDV-S X 1 2 IR EXTENDER IR BLASTER POWER ADAPTER 24/1.25A USER’S MANUAL IR REMOTE OK INPUT EXIT MENU RESET AUTO ADJUST

7 1. SERVICE: Reserved for manufacturer use only. 2. IR RECEIVER WINDOW: Receives only the IR signal from the supplied remote control for this device only. 3. HDMI: Connect to a digital source device such as Bluray Set Top Box. 4. VGA: Connect to a Laptop/Desktop source with a D-Sub 15 Pin cable. 5. AUDIO: Connect to an analog stereo (L/R) audio source with a 3.5mm mini-jack cable. 6. MENU: This button enters the On-Screen Display (OSD) menu. INPUT (–) Button & HDMI/PC LED: Press the INPUT (−) button to toggle between CV or PC inputs. When in CV mode the LED will be lit, off when in PC mode. 7. −/+: Use these buttons to navigate down and up in the on-screen menu. 8. ENTER: Press this button to confirm the selection. Also:- Press this button together with [–] key to switch output timing to 720p@60 instantly. Press this button together with [+] key to switch output timing to XGA (1024x768) instantly. 9. 1 2 3 4 5 6 9 8

1. POWER LED: This LED will illuminate when the device is connected to an active power supply. 2. DC 24V: Connect the 24 V DC power supply to the unit and plug the adaptor into an AC outlet. Only one unit requires powering if both the Transmitter and Receiver are both PoE compatible. 3. RS-232 IN: Connect to a PC or RS-232 control system with a D-Sub 9 pin male cable for the transmission of RS-232 commands. 4. LAN: Connect to an active network for LAN serving. When any compatible LAN equipped receivers are connected, this allows the network access (including internet access if available) to be shared between any connected LAN equipped receivers 100Mbps. Connect any Ethernet equipped device e.g. a Smart TV or games console to the LAN port of a receiver for that device to share the network/ internet access. 2 3 4 5 6 7 1 5. IR Blaster: Connect the supplied IR Blaster cable for IR signal transmission. Place the IR Blaster in direct line-of- sight of the equipment to be controlled. 6. IR Extender: Connect the supplied IR Receiver cables for IR signal reception. Ensure that remote being used is within the direct lineof-sight of the IR Extender. 7. CAT5e/6/7 OUT: Connect to the Receiver unit with a single CAT5e/6/7 cable for transmission of all data signals. MODE LED: This LED will illuminate when the power is connected. LINK LED: This LED will illuminate when connected to a Receiver unit that is connected with a TV/monitor that is displaying the signal. PANEL DESCRIPTION

2 EXIT: Press this button to exit the menu or the current selection in the on-screen menu. 3 MENU: Press this button to enter into the OSD menu. 4 RESET: Press this button to return the device to the factory default settings. 5 AUTO ADJUST: Press this button tooptimize the positioning of the picture (picture centering) on the screen. 6 OK & ▲▼◄►: Press 'OK' to confirm the selection or use the directional buttons to navigate the on-screen menus. 7.4 IR Cable Pin Assignment 3 1 3 1 2 2 Power IR Blaster Signal NC IR Signal Power Ground IR Extender IR Blaster OK INPUT EXIT MENU RESET AUTO ADJUST 1 2 4 6 3 5

1 N/C 2 TxD/RxD 3 RxD/TxD 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC 8. RS-232 PIN DEFINITIONS www.avenview.com Page 9 RS-232 SETTINGS Baud Rate: 9600bps Data Bit: 8 bits parity: None Flow Control: None Stop Bit: 1

1=PC 2=HDMI R SOURCE Reports the numerical equivalent for the SOURCE setting (as listed above) S OUTPUT 0~25 12=1600×1200 0=Native 1=640×480 2=800×600 3=1024×76 85=1360×768 6=1280×720 7=1280×800 8=1280×1024 9=1440×900 10=1400×1050 11=1680×1050 13=1920×1080 16=1920×1200 17=480p 18=720p@60 19=1080p@60 20=1080i@60 22=576p 23=720p@50 24=1080p@50 25=1080i@50 R OUTPUT Reports the numerical equivalent for the OUTPUT setting (as listed above) S SIZE 0~6 0=OVERSCAN 4=LETTER BOX 1=FULL 5=UNDER 2 2=BEST FIT 6=UNDER 1 R SIZE 3=PAN SCAN Reports the numerical equivalent for the SIZE setting (as listed above) Sets the numerical value for the CONTRAST setting (0~60) S CONTRAST 0~60 R CONTRAST Reports the numerical value for the CONTRAST setting (0~60) Sets the numerical value for the BRIGHTNESS setting (0~60) S BRIGHTNESS 0~60 R BRIGHTNESS Reports the numerical value for the BRIGHTNESS setting (0~60) 9. RS-232 COMMANDS www.avenview.com Page 10

Sets the numerical value for the HUE setting (0~60) R HUE Reports the numerical value for the HUE setting Sets the numerical value for the SATURATION setting (0~60) S SATURATION 0~60 R SATURATION Reports the numerical value for the SATURATION setting (0~60) Sets the numerical value for SHARPNESS setting (0~30) S SHARPNESS 0~30 R SHARPNESS Reports the numerical value for the SHARPNESS setting (0~30) S NR 0~3 0=OFF 2=MIDDLE 1=LOW 3=HIGH R NR Reports the numerical equivalent for the NOISE REDUCTION setting (as listed above) S AUDIO DELAY 0~3 0=OFF 2=110ms 1=40ms 3=150ms R AUDIO DELAY Reports the numerical equivalent for the AUDIO DELAY setting (as listed above) S AUDIO MUTE 0/1 R AUDIO MUTE 0=ON 1=MUTE Reports the numerical equivalent for the AUDIO MUTE setting (as listed above) FW Checks the FIRMWARE version S RESET 1 Sets the numerical equivalent for the RESET setting (as left) Note: 1. RS-232 commands will not execute unless followed by a carriage return and LF (Line Feed). 2. Commands are not case-sensitive. 3. Resolutions 1~16 are RGB encoded and 17~25 are YUV encoded. www.avenview.com Page 11 0=ENABLE 1=DISABLE S KEY LOCK 0/1 R KEY LOCK Reports the numeric equivalent for the KEY LOCK setting (as listed above) S AUTOSCAN 0/1 0=DISABLE 1=ENABLE R AUTOSCAN Reports the numeric equivalent for AUTO SCAN setting (as above)

1 ST LAYER 2 ND LAYER 3 RD LAYER 4 TH LAYER DISPLAY OUTPUT Native 640x480 60 800x600 60 1024x768 60 1360x768 60 1280x720 60 1280x800 60 1280x1024 60 1440x900 60 1400x1050 60 1680x1050 60 1600x1200 60 1920x1080 60 1920x1200 60 720x480P 60 1280x720P 60 1920x1080I 60 1920x1080P 60 720x576P 50 1280x720P 50 1920x1080I 50 1920x1080P 50 SIZE SIZE OVER SCAN FULL ASPECT RATIO PAN SCAN LETTER BOX UNDER 2 UNDER 1 10. OSD MENU www.avenview.com Page 12

NO YES H_POSITION 0~60 (30) V_POSITION 0~60 (30) PHASE CLOCK WXGA/XGA XGA WXGA RESET NO YES COLOR COLOR R G B R OFFSET G OFFSET B OFFSET CONTRAST 0~60 BRIGHTNESS 0~60 HUE 0~60 SATURATION 0~60 SHARPNESS 0~60 NR. OFF LOW MIDDLE HIGH www.avenview.com Page 13

INPUT RESOLUTION HDMI PC NTSC/PAL  - VGA@60/72/75 Hz -  SVGA@56/60/72/75 Hz  XGA@60/70/75 Hz  SXGA@60/75 Hz  UXGA@60 Hz  1280×800@60 Hz  1680×1050@60 Hz (RB)  1920×1080@60 Hz  www.avenview.com Page 14 Note: Items in Bold are the default settings. 480i/576i 480p/576p 720p@50/60 Hz 1080i@50/60 Hz 1080p@50/60 Hz             - - - - -

1. PKKP power off all sources such as media player, set-top box, pC etc; 2. PUUL Connect both HDMI/VGA video Source to the HDMI & VGA INpuT of (HBT-C6POE-HDV-S); 3. K Connect HBT-C6POE-HDV-S to HBT-C6POE-R with a CAT5e/6 at the CAT5e/6 OUT; 4. Connect HBT-C6POE-R to TV/Monitor with HDMI Cable; 5. P K 6. PKKUL power on HDMI & VGA Source and TV/MONITOR; 7. L When the Input is connected and powered on the corresponding POWER lED will light . LUL 13. GENERAL TROUBLESHOOTING PROBLEM POSSIBLE SOLUTION NO IMAGE••ULK•P•LFPP•Pmage••KKU•YP•UPYPYP•YPFPYLL • Check if connection to the source and the display are correct. • Ensure that display device supports resolution from 640 up to 1080p. • • Check Power lED , MODE and Link lights on the CAT5E/6 connector MODE LED: This LED will illuminate when the power is connected. LINK LED: This LED will illuminate when connected to a Receiver unit that is connected with a TV/monitor that is displaying the video and audio signal. • Check INPUT (–) Button & HDMI/PC LED: Press the INPUT (−) button to toggle between HDMI or PC inputs. When in HDMI mode the LED will be Red, LED Green when in PC mode. (Section 3 panel Description) please use the supplied power supply-24V DC

OUTPUT BANDWIDTHY 300MHz / 10.2Gbps HDMI RESOLUTION SUPPORT 480i~1080p VGA RESOLUTION SUPPORT VGA~WUXGA (RB) CAT5 RESOLUTION SUPPORT HD: Up to 1080p@60 Hz / PC: Up to WUXGA (RB)p IR FREQUENCY 30~50 kHz INPUTKKUULUFULLU 1×HDMI, 1×VGA, 1×3.5mm, Mini-jack (L/R), 1×RS-232, 1×LAN, 1×IR Extender OUTPUTLPP 1×CAT5e/6/7, 1×IR Blaster DIMENSIONS (WxDxH) 7.9" x 5.7" x 1.2" (Jacks Included) NET WEIGHTL 1.33lbs POWER SUPPLY 24V/2.7A DC / 110-240V POWER CONSUMPTION 17W ESD PROTECTION 1 x HDMI Type A (19 pin female)FPUUFUL Environmental Operating Temperature 32˚ ~ 104˚F (0˚ to 40˚C) Storage Temperature -4˚ ~ 140˚F (-20˚ ~ 60˚C) Relative Humidity 20~90% RH (non-condensing)

AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications. LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs, please contact [email protected]. PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact [email protected]. To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight charges and brokerages when shipping the product(s) to the receiver. NOT COVERED BY THIS WARRANTY This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire, earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service performed by anyone who is not a representative of Avenview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s). AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS; LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. 275 Woodward Avenue, Kenmore, NY 14217 1.866.508.0269

Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein. Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement. Control Your Video Avenview USA Avenview Head Office 275 Woodward Avenue Kenmore, NY 14217 Phone: 1.716.218.4100 F ax: 1.866.387.8764 Email: [email protected] Avenview Canada Avenview Sales 151 Esna Park Drive, U nits 11 & 12 Markham, ON, L 3R 3B1 Phone: 1.905.907.0525 F ax: 1.866.387.8764 Email: [email protected] Avenview Europe Avenview Europe Demkaweg 11 3555 HW U trecht Netherlands Phone: +31(0)85.2100.613 Email: [email protected] Avenview Hong Kong U nit 8, 6/F., Kwai Cheong Centre, 50 Kwai Cheong Road, Kwai Chung, N.T. Hong Kong Phone: 852.3575.9585 Email: [email protected]