Aria Aria-24 Programming Manual

Digital Key Telephone System Programming Manual LG Electronics, Inc. Aria Communications Quadrant Business Park Unit 3 / 15 Pickering Road Mulgrave VIC 3170 ABN : 22 090 723 925

CONFIDENTIALITY The information contained in this manual is the property of Aria Communications Pty. Limited. The contents of this manual must not be copied, distributed or made available to any third party without the prior written consent of Aria Communications Pty. Limited. Every effort has been made to ensure that this manual documents the operation of the Aria-24/130c/130/300/600ipe Digital Key Telephone System. However, due to the on-going improvement and update of software, Aria Communications cannot guarantee the accuracy of printed material after the date of publication, nor can Aria Communications accept responsibility for errors or omissions. Revised manuals will be published as needed. This manual supersedes all previous issues.

Programming Manual III CONTENTS 1 CUSTOMER DATABASE PROGRAMMING ....................................................... 8 1.1 INTRODUCTION ......................................................................................................................... 8 1.2 TO ENTER THE PROGRAMMING MODE ................................................................................. 9 1.3 PERMANENT UPDATE PROCEDURE ...................................................................................... 9 1.4 NUMBERING PLAN .................................................................................................................. 10 1.5 ADMIN PROGRAMMING INDEX .............................................................................................. 16 1.6 DEFAULT VALUES ................................................................................................................... 19 TABLE 1.6.1 LOCATION PROGRAM ........................................................................................... 19 TABLE 1.6.2 RACK SLOT ASSIGNMENT .................................................................................... 19 TABLE 1.6.3 WTIB PORT NUMBER ASSIGNMENT .................................................................... 19 TABLE 1.6.4 LOGICAL SLOT ASSIGNMENT .............................................................................. 20 TABLE 1.6.5 NUMBERING PLAN TYPE ...................................................................................... 20 TABLE 1.6.6 FLEXIBLE NUMBERING PLAN ............................................................................... 21 TABLE 1.6.7 IP SETTING ............................................................................................................. 23 TABLE 1.6.8 EXPANDED FLEXIBLE NUMBERING PLAN .......................................................... 23 TABLE 1.6.9 STATION ID ASSIGNMENT .................................................................................... 23 TABLE 1.6.10 STATION ATTRIBUTE I/II/III ............................................................................... 24 TABLE 1.6.11 ISDN STATION ATTRIBUTE ............................................................................... 25 TABLE 1.6.12 FLEXIBLE BUTTON ASSIGNMENT ................................................................... 26 TABLE 1.6.13 STATION BASE PROGRAM ............................................................................... 26 TABLE 1.6.14 TABLE COPY DSS BUTTON .............................................................................. 27 TABLE 1.6.15 DISPLAY STATION NUMBER BY COS .............................................................. 27 TABLE 1.6.16 DISPLAY STATION NUMBER BY CO ACCESSS .............................................. 27 TABLE 1.6.17 CO LINE BASE PROGRAM ................................................................................ 28 TABLE 1.6.18 CO MSN Mapping Table ...................................................................................... 31 TABLE 1.6.19 ISDN CO BASE PROGRAM ................................................................................ 32 TABLE 1.6.20 SYSTEM TIMER PROGRAM .............................................................................. 36 TABLE 1.6.21 DCOB ATTRIBUTE .............................................................................................. 38 TABLE 1.6.22 STATION GROUP ASSIGNMENT ...................................................................... 38 TABLE 1.6.23 STATION GROUP PROGRAM ........................................................................... 38 TABLE 1.6.24 ISDN ATTRIBUTES ............................................................................................. 40 TABLE 1.6.25 LCR TABLE ASSIGNMENT................................................................................. 42 TABLE 1.6.26 TOLL TABLE ASSIGNMENT ............................................................................... 43 TABLE 1.6.27 OTHER TABLES .................................................................................................. 43 TABLE 1.6.28 NETWORKING ATTRIBUTE ............................................................................... 45 TABLE 1.6.29 VOIB NET ATTRUBUTE ...................................................................................... 45 TABLE 1.6.30 NATION SPECIFIC .............................................................................................. 49 TABLE 1.6.31 INITIALIZATION ................................................................................................... 54 TABLE 1.6.32 PRINT PROT DATABASE ................................................................................... 55 2 PRE-PROGRAMMED DATABASE .................................................................... 56 2.1 LOCATION PROGRAM (PGM 100) ......................................................................................... 57 2.2 RACK SLOT ASSIGNMENT (PGM 101) .................................................................................. 58 2.3 WTIB PORT NUMBER ASSIGNMENT (PGM 102) ................................................................. 59 2.4 LOGICAL SLOT ASSIGNMENT (PGM 103) ............................................................................ 59

Programming Manual IV 2.5 NUMBERING PLAN TYPE (PGM 104) .................................................................................... 60 2.6 FLEXIBLE NUMBERING PLAN (PGM 105) ............................................................................. 61 2.7 FLEXIBLE NUMBERING PLAN (PGM 106-107) ..................................................................... 62 2.8 IP SETTING (PGM 108) ........................................................................................................... 65 2.9 EXPANDED FLEXIBLE NUMBERING PLAN (PGM 109) ........................................................ 66 2.10 HOTDESK AGENT ATTRIBUTE (PGM 250) ............................................................................ 67 3 STATION PROGRAMMING ............................................................................... 68 3.1 STATION ID (PGM 110) ........................................................................................................... 68 3.2 STATION ATTRIBUTE – I (PGM 111) ..................................................................................... 71 3.3 STATION ATTRIBUTE - II (PGM 112) ..................................................................................... 72 3.4 STATION ATTRIBUTE - III (PGM 113) .................................................................................... 75 3.5 ISDN STATION ATTRIBUTE (PGM 114) ................................................................................. 77 3.6 FLEX BUTTON ASSIGNMENT (PGM 115) ............................................................................. 79 3.7 STATION COS (PGM 116) ....................................................................................................... 81 3.8 CO LINE GROUP ACCESS (PGM 117) ................................................................................... 83 3.9 INTERNAL PAGE ZONE (PGM 118) ....................................................................................... 84 3.10 CONFERENCE PAGE ZONE (PGM 119) ................................................................................ 85 3.11 ICM TENANCY GROUP (PGM 120) ........................................................................................ 86 3.12 PRESET CALL FORWARD (PGM 121) ................................................................................... 87 3.13 HOT LINE / WARM LINE (PGM 122) ....................................................................................... 88 3.14 CTI STATION ATTRIBUTE (PGM 123).................................................................................... 89 3.15 SMDR ACCOUNT GROUP (PGM 124) ................................................................................... 90 3.16 COPY DSS BUTTON (PGM 125) ............................................................................................. 91 3.17 DISPLAY STATION NUMBER BY COS (PGM 130) ................................................................. 91 3.18 DISPLAY STATION NUMBER BY CO ACCESS GROUP (PGM 131) ..................................... 92 4 CO LINE PROGRAMMING ................................................................................ 93 4.1 CO SERVICE TYPE (PGM 140) .............................................................................................. 93 4.2 CO LINE ATTRIBUTE – I (PGM 141)....................................................................................... 96 4.3 CO LINE ATTRIBUTE – II (PGM 142)...................................................................................... 98 4.4 ISDN CO LINE ATTRIBUTE I (PGM 143) .............................................................................. 100 4.5 CO RING ASSIGNMENT (PGM 144) ..................................................................................... 102 4.6 CO RING ASSIGNMENT DISPLAY (PGM 145) ..................................................................... 103 4.7 ISDN CO LINE ATTRIBUTE II (PGM 146) .............................................................................. 104 4.8 CO MSN MAPPING TABLE (PGM 147) .................................................................................. 105 5 SLOT PROGRAMMING ................................................................................... 106 5.1 BOARD ATTRIBUTE (PGM 155) ............................................................................................ 106 6 SYSTEM DATA PROGRAMMING ................................................................... 107 6.1 SYSTEM ATTRIBUTE - I (PGM 160) ..................................................................................... 107 6.2 SYSTEM ATTRIBUTE - II (PGM 161) .................................................................................... 110 6.3 ADMIN PASSWORD (PGM 162) ........................................................................................... 112 6.4 ALARM ATTRIBUTES (PGM 163) ......................................................................................... 112 6.5 ATTENDANT ASSIGNMENT (PGM 164)............................................................................... 113

Programming Manual V 6.6 AUTO ATTENDANT VMIB ANNC ASSIGNMENT (PGM 165) .............................................. 114 6.7 CO-TO-CO COS (PGM 166) .................................................................................................. 115 6.8 DID/DISA DESTINATION (PGM 167) .................................................................................... 116 6.9 EXTERNAL CONTROL CONTACT (PGM 168) ..................................................................... 118 6.10 LCD TIME/DATE/LANGUAGE DISPLAY MODE (PGM 169) ................................................ 120 6.11 MODEM (PGM 170) ............................................................................................................... 121 6.12 MUSIC (PGM 171) .................................................................................................................. 122 6.13 PBX ACCESS CODE (PGM 172) ........................................................................................... 124 6.14 PLA PRIORITY SETTING (PGM 173).................................................................................... 124 6.15 RS-232C PORT SETTING (PGM 174)................................................................................... 125 6.16 PRINT PORT SELECTION (PGM 175) .................................................................................. 126 6.17 PULSE DIAL RATIO (PGM 176) ............................................................................................ 127 6.18 SMDR ATTRIBUTES (PGM 177) ........................................................................................... 128 6.19 SYSTEM TIME/DATE SETTING (PGM 178) ......................................................................... 131 6.20 LINKED STATION PAIRS TABLE (PGM 179) ....................................................................... 132 6.21 CIDU SETTINGS (PGM 185) .................................................................................................. 133 7 SYSTEM TIMERS ............................................................................................ 134 7.1 SYSTEM TIMERS - I (PGM 180) ........................................................................................... 134 7.2 SYSTEM TIMERS - II (PGM 181) .......................................................................................... 136 7.3 SYSTEM TIMERS - III (PGM 182) ......................................................................................... 138 7.4 CIDU SETTING (PGM 185) .................................................................................................... 139 8 DCOB ATTRIBUTE (PGM 186 - PGM 187) .................................................... 140 9 STATION GROUP PROGRAMMING (PGM 190 - PGM 191) .......................... 141 9.1 STATION GROUP ASSIGN (PGM 190)................................................................................. 141 9.2 STATION GROUP ATTRIBUTE (PGM 191) .......................................................................... 143 10 ISDN PROGRAM ............................................................................................. 152 10.1 ISDN ATTRIBUTE (PGM 200) ............................................................................................... 152 10.2 COLP TABLE (PGM 201) ....................................................................................................... 154 10.3 MSN TABLE (PGM 202) ......................................................................................................... 155 10.4 ISDN ATTRIBUTES II (PGM 203) ARIA-24 ONLY ................................................................. 156 11 LCR .................................................................................................................. 157 11.1 LCR ATTRIBUTES (PGM 220) .............................................................................................. 157 11.2 LEADING DIGIT TABLE (PGM 221) ...................................................................................... 159 11.3 DIGIT MODIFICATION TABLE (PGM 222) ............................................................................ 161 11.4 LCR TABLE INITIALIZATION (PGM 223) .............................................................................. 163 12 TOLL TABLE ................................................................................................... 165 12.1 TOLL EXCEPTION TABLE (PGM 224) .................................................................................. 165 12.2 CANNED TOLL TABLE (PGM 225) ....................................................................................... 167 12.3 EMERGENCY CODE TABLE (PGM 226) .............................................................................. 168 13 TABLES ........................................................................................................... 169

Programming Manual VI 13.1 AUTHORIZATION CODE TABLE (PGM 227) ........................................................................ 169 13.2 CUSTOM CALL ROUTING (PGM 228) .................................................................................. 170 13.3 EXECUTIVE / SECRETARY TABLE (PGM 229) ................................................................... 172 13.4 FLEXIBLE DID TABLE (PGM 231) ......................................................................................... 173 13.5 SYSTEM SPEED ZONE (PGM 232) ...................................................................................... 175 13.6 WEEKLY TIME TABLE (PGM 233) ........................................................................................ 176 13.7 VOICE MAIL DIALING TABLE (PGM 234) ............................................................................ 177 13.8 TIE ROUTING TABLE (PGM 235) ......................................................................................... 178 13.9 MOBILE EXTENSION TABLE (PGM 236) ............................................................................. 179 14 NETWORKING ATTRIBUTE ........................................................................... 180 14.1 NETWORKING BASIC ATTRIBUTE (PGM 320) ................................................................... 180 14.2 NETWORKING SUPPLEMENTARY ATTRIBUTE (PGM 321) .............................................. 181 14.3 NETWORKING CO LINE ATTRIBUTE (PGM 322) ................................................................ 182 14.4 NETWORKING ATTENDANT ASSIGNMENT (PGM 323) ...................................................... 183 14.5 NETWORKING ROUTING TABLE (PGM 324) ....................................................................... 184 15 VOIB ATTRIBUTE ............................................................................................ 185 15.1 VOIP IP SETTING (PGM 340) ............................................................................................... 185 16 RSG/IP PHONE PROGRAMMING ................................................................... 186 16.1 VOIB SLOT ASSIGNMENT FOR RSG/IP PHONE (PGM 380) .............................................. 186 16.2 RSG/IP PHONE PORT NUMBER ASSIGNMENT (PGM 381) ............................................... 187 16.3 RSG / IP PHONE ATTRIBUTE (PGM 382) ............................................................................ 188 16.4 RSG ATTRIBUTE 1 (PGM 383) ............................................................................................. 189 16.5 RSG ATTRIBUTE 2 (PGM 384) ............................................................................................. 190 16.6 RSG ALARM ASSIGNMENT (PGM 385) ............................................................................... 192 16.7 RSG ATTRIBUTE 1 (PGM 386) ............................................................................................. 193 16.8 RSG DKT RX GAIN CONTROL (PGM 390) .......................................................................... 194 16.9 RSG DKT TX GAIN CONTROL (PGM 391) ........................................................................... 195 16.10 RSG SLT RX GAIN CONTROL (PGM 392) ........................................................................... 196 16.11 RSG SLT TX GAIN CONTROL (PGM 393)............................................................................ 197 16.12 RSG LCO RX GAIN CONTROL (PGM 394) .......................................................................... 198 16.13 RSG LCO TX GAIN CONTROL (PGM 395) ........................................................................... 199 16.14 RSG IP PHONE RX GAIN CONTROL (PGM 396) ................................................................ 200 16.15 RSG IP PHONE TX GAIN CONTROL (PGM 397) ................................................................. 201 17 NATION SPECIFIC PROGRAMMING ............................................................. 202 17.1 DTIB RX GAIN CONTROL (PGM 400) .................................................................................. 202 17.2 SLIB RX GAIN CONTROL (PGM 401) ................................................................................... 203 17.3 CTR SLIB RX GAIN CONTROL (PGM 402) .......................................................................... 204 17.4 WTIB RX GAIN CONTROL (PGM 403).................................................................................. 205 17.5 ACOB RX GAIN CONTROL (PGM 404) ................................................................................ 206 17.6 CTR ACOB RX GAIN CONTROL (PGM 405) ........................................................................ 207 17.7 DCOB RX GAIN CONTROL (PGM 406) ................................................................................ 208 17.8 VMIB RX GAIN CONTROL (PGM 407) .................................................................................. 209

Programming Manual VII 17.9 DTMF RCVR RX GAIN CONTROL (PGM 408) ..................................................................... 210 17.10 EXT PAGE RX GAIN CONTROL (PGM 409) ........................................................................ 211 17.11 CPT RX GAIN CONTROL (PGM 410) ................................................................................... 212 17.12 MODEM RX GAIN CONTROL (PGM 411) ............................................................................. 213 17.13 SYSTEM TONE FREQUENCY (PGM 420) ........................................................................... 214 17.14 DIFFERENTIAL RING FREQUENCY (PGM 421) .................................................................. 215 17.15 DISTINCT RING FREQUENCY (PGM 422) ........................................................................... 216 17.16 ACNR TONE CADENCE (PGM 423) ..................................................................................... 217 18 INITIALIZATION (PGM 450) ........................................................................... 218 19 PRINT PROT DATABASE (PGM 451) ............................................................ 219 20 INITIALIZE BY MPB VERSION (PGM 452) ..................................................... 220

Programming Manual 8 1 CUSTOMER DATABASE PROGRAMMING 1.1 INTRODUCTION The ARIA Key Telephone System can be programmed to meet each customer's individual need. All programming is done at station 100 (station port # 00) using KD-36D, LKD-30DS, LDP-7024D and LDP-7024 LD digital key telephone. (You cannot program with the KD Large Display ) Additional programming stations may be assigned (PGM 113-BTN 1), but only 1 keyset can be active in programming mode at any one time. Upon entering the program mode, the key telephone at station 100 cannot operate as a normal telephone but as a programming instrument with all of the buttons redefined. The keys of the dial pad are used to enter the various data fields and to enter numerical information. The 24 buttons located at the top of the phone (Flexible Buttons) are used to indicate the specific data field and to enter information. Sometimes the [SPEED] button and „*‟ of the dial pad is used to delete the data or to indicate end of data input and the [REDIAL] button is used to delete one digit or character from the end of entered digits or characters. See TABLE 1.6.1 - 1.6.27 for default data. If this pre-programming suits the customer, additional admin program is not necessary. To change admin data, the user enters the admin programming mode and select program code. During admin programming, other keysets operate normally. (While activating ARIA Admin, no keyset can enter Admin mode and the reverse also.) When Admin programming, LCD and LEDs indicate the current programmed data and status. If the programmer enters correct data, then LCD and LEDs show the entered data and the data is stored in the temporary buffer area. Real system database is not changed and has no effect on telephone operation unless permanent updating procedure is executed. Pressing the [HOLD/SAVE] button, all data in the temporary buffer (same as LCD and LEDs show their status) is saved into permanent memory. Tones are provided to let the programmer know data entry is correct (confirmation tone) or not (error tone). To return the parent state while admin programming, press the [CONF] button. Pressing the [CONF] button, temporary data fields are cleared. To reset the system, enter PGM 450 – BTN 15 and press [HOLD/SAVE] button. Or, the system will be reset automatically after programming PGM100 – BTN 1 (Nation Code Assign)

Programming Manual 9 1.2 TO ENTER THE PROGRAMMING MODE 1. Lift handset or press the [MON] button on the admin station, and hear ICM dial tone (optional). 2. Press the [TRANS/PGM] button and dial ＊# (Confirmation tone is heard). 3. Enter admin password if the password has been set. This places the station into the admin programming mode (Confirmation tone is heard). 4. Each program is accessed by pressing the [TRANS/PGM] button and dialing the three-digit program number. If an error is made while entering data, the [TRANS/PGM] button can go the previous status. When the [TRANS/PGM] button is pressed, the LCD will display; ENTER PROGRAM CODE 1.3 PERMANENT UPDATE PROCEDURE When the data has been entered, the [HOLD/SAVE] button is used to store the data permanently. If all data was entered correctly, confirmation tone is heard when pressing the [HOLD/SAVE] button. If there were any errors in the entry, then an error tone is presented and data is not stored in the permanent memory.

Programming Manual 10 1.4 NUMBERING PLAN The following numbering plan can be changed by Admin Programming 104-107 depending on the user's needs. NUMBER ITEM REMARK Aria-24 Aria- 130/130c Aria-300 Aria-600 10-37 100-227 100 – 399 1000-1599 Intercom Call 620-629 620-634 620 – 667 620-667 Group Pilot Number #01 – #10 #01 – #15 #01 – #35 #01-#35 Internal Page Zone #5 #5 #5 # 5 Internal All Call Page ## ## ## # # Meet Me Page #6 #6 #6 # 6 External Page Zone 1 N/A #7 #7 # 7 External Page Zone 2 N/A #8 #8 # 8 External Page Zone 3 N/A #9 #9 # 9 External All Call Page #00 #00 #00 # 00 All Call Page (Int & Ext) 550 550 550 550 SMDR Account Code Enter SLT 551 551 551 551 Flash Command to CO Line SLT 552 552 552 552 Last Number Redial SLT 553 553 553 553 DND (Toggle On/Off) SLT 554 554 554 554 Call Forward SLT 555 555 555 555 Speed Dial Programming SLT 556 556 556 556 Message Wait/Callback Enable SLT 557 557 557 557 Message Wait/Callback Return SLT 558 558 558 558 Speed Dial Access SLT 559 559 559 559 Cancel DND/FWD/Pre-MSG SLT 560 560 560 560 System Hold SLT N/A 561 561 561 Station Relocation Backup N/A 562 562 562 Station Relocation Retrieve 563 563 563 563 Programming Mode Enter Code SLT 564 564 564 564 ACD Reroute 565 565 565 565 Alarm Reset ** ** ** ** Group Call Pickup 568 568 568 568 UCD DND 577 577 577 577 Night Answer 601-608 601-610 601 - 619 601-619 Call Parking Locations *7 *7 *7 *7 Direct Call Pickup 801-808 801-824 801-872 801-872 CO Group Access 8801-8840 8801-8840 88001- 88200 8801-88400 Individual CO Access 8901 8901 8901 8901 Tie Routing Access

Programming Manual 11 NUMBER ITEM REMARKS Aria-24 Aria- 130c/130 Aria-300 Aria-600 8* 8* 8* 8* Retrieve Held CO Line 8#xx 8#xx 8#xxx 8#xxx Retrieve Held Individual CO Line 9 9 9 9 Access CO Line In the 1st available CO Group 0 0 0 0 Attendant Call #*1 #*1 #*1 #*1 1st Door Open #*2 #*2 #*2 #*2 2nd Door Open N/A #*3 #*3 #*3 3rd Door Open N/A #*4 #*4 #*4 4th Door Open N/A #*5 #*5 #*5 5th Door Open N/A #*6 #*6 #*6 6th Door Open N/A N/A #*7 #*7 7th Door Open N/A in ARIA- 130 *8 *8 *8 *8 VM Message Waiting Enable *9 *9 *9 *9 VM Message Waiting Disable NUMBER ITEM REMARKS Aria-24 Aria- 130c/130 Aria-300 Aria-600 *0 *0 *0 *0 MCID Request *1 *1 *1 *1 RSG Door Open 1 *2 *2 *2 *2 RSG Door Open 2 *57 *57 *57 *57 Enter Conference Room *58 *58 *58 *58 SLT Conference Page Join *## *## *## *## Unsupervised Conf Tmr Extend

Programming Manual 12  To enter user programming mode, press the [TRANS/PGM] button  in a keyset or dial 5 6 3 (Programming enter code) in a SLT.  The following numbering plan is fixed, so it cannot be changed by Admin Programming. 1) For the stations NUMBER ITEM REMARK 11 Differential Ring Keyset 12 Intercom Answer Mode (1 HF / 2 TONE / 3 PV) Keyset 13 SMS Message Display 14 Enblock Mode 15 SMS/Notice Display 16 Scroll Speed 17 Ear-Mic Headset 18 Intercom Bell 19 CO Bell 21 Station COS Down 22 Station COS Restore 23 Walking COS Keyset 24 COS CHANGE 31 Authorization Code Registration 32 Authorization Code Change 33 Register Mobile Extension 34 Activate Mobile Extension 41 Wake-up Time Registration (One-time/ Continuous) 42 Wake-up Time Cancel 43 Activate Conference Room 44 Deactivate Conference Room 51 Pre-selected MSG Activation 52 Set Custom Message 61 Record VMIB User Greeting 62 Listen VMIB Time & Date 63 Listen VMIB Station Number 64 Listen VMIB Station Status 65 Record VMIB Page Message 66 Erase VMIB User Greeting 67 Erase VMIB Page Message 71 LCD Display Mode (English/Domestic Language) Keyset 72 MPB Version Display Keyset 73 Background Music Keyset 74 Station User Name Registration 75 Headset/Speakerphone Mode Keyset 76 Headset Ring Mode Keyset 77 WTU Station Number Receive Keyset 78 Serial No/SW Packages Keyset with LCD 79 PC-Phone Lock Key ** Hot Desk Logout

Programming Manual 13 *0 Hot Desk Login *1 Station Relocation Out *2 Station Relocation In *3 Register Bluetooth *4 Bluetooth Usage 2) For the attendant NUMBER ITEM REMARK 0111 Print SMDR (Station Base) System Attendant 0112 Delete SMDR (Station Base) System Attendant 0113 Print SMDR (Group Base) System Attendant 0114 Delete SMDR (Group Base) System Attendant 0115 Display Call Charge System Attendant 0116 Abort Printing System Attendant 0117 Print Lost Call System Attendant 0118 Delete Lost Call System Attendant 0121 Print All Summary System Attendant 0122 Print All Periodically System Attendant 0123 Abort Periodic Printing System Attendant 0124 Print ATD Traffic System Attendant 0125 Print Call Summary System Attendant 0126 Print All Hourly System Attendant 0127 Print H/W Usage System Attendant 0128 Print CO Summary System Attendant 0129 Print CO Hourly System Attendant 021 Station COS Down (COS 7) Attendant 022 Station COS Restore Attendant 031 Authorization Code Cancel System Attendant 041 System Date/Time Setting Attendant 042 Wake-up Time Registration (One-time /Continuous) Attendant 043 Wake-up Time Cancel System Attendant 044 LCD Date Mode Change System Attendant 045 LCD Time Mode Change System Attendant 046 Use Network Time & Date System Attendant 047 Monitor Conference Room Attendant 051 Pre-select MSG Activation Attendant 052 Pre-select MSG Deactivation Attendant 053 Custom Display Message Program (11-20) System Attendant 054 Erase VM MSG Attendant 055 ATD DEL ALL CLI MSG 06 Record VMIB System Greeting System Attendant 071 DND/Call Forward/Pre-selected MSG Cancel Attendant 072 Register Station Name Attendant 073 Disable CO Outgoing System Attendant 074 Automatic Day/Night/Weekend Mode Program Attendant 075 ICM BOX BGM Channel select Attendant 076 External Page Music -1 Assignment/Cancel Attendant 077 External Page Music -2 Assignment/Cancel Attendant 078 External Page Music -3 Assignment/Cancel Attendant

Programming Manual 14 079 Prepaid Call 07* LCD Display Language 0# WHTU Subscription 0* Board Service Switch – Enter slot number Attendant 3) Flexible Button Programming Code NUMBER ITEM REMARK 11 Differential Ring 18 ICM RING 19 CO RING 21 Station COS Down 22 Station COS Restore 23 Walking COS 24 COS CHANGE 31 Authorization Code Registration 32 Authorization Code Change 41 Wake-up Time Registration (One-time /Continuous) 42 Wake-up Time Cancel 43 CONF – ROOM ACTIVE 44 CONF – ROOM DEACTIVE 51 Pre-selected MSG Activation 52 Set Custom Message 53 CLIR Key 54 Two Way Recording 55 Attendant DND Networking Only 56 Attendant CampOn(Queue) BTN Assignment Attendant 57 Call Log Button 61 Record VMIB User Greeting 62 PLAY DATE TIME 63 PLAY STA NUMBER 64 Listen VMIB Station Status 65 RECORD PAGING MESSAGE 66 Erase VMIB User Greeting 67 DELETE PAGING MESSAGE 68 ANSWER MACHINE - RING 69 ANSWER MACHINE - SPEAKER 71 LCD Display Mode (English/Domestic Language) 73 Background Music 74 Station User Name Registration 75 Headset/Speakerphone Mode 76 HeadSet Ring Mode 80 Account Code Activation 81 DID Call Wait 83 [ICM Hold] BTN Assignment 84 [LOOP] BTN Assignment

Programming Manual 15 84# MSN Button 85 [Camp-on] BTN Assignment 86 [INTRUSION] BTN Assignment System Attendant 87 [UCD DND] BTN Assignment + Hunt Grp No. 89 Keypad Facility Key 8* {ACD STATUS} BTN Assignment 8# PAGER CALL 91 [CONF] BTN Assignment 2/8 BTN Keyset 92 [CALLBK] BTN Assignment 2/8 BTN Keyset 93 [DND/FWD] BTN Assignment 2/8 BTN Keyset 94 [FLASH] BTN Assignment 2/8 BTN Keyset 95 [MUTE] BTN Assignment 2/8 BTN Keyset 96 [MON] BTN Assignment 2/8 BTN Keyset 97 [REDIAL] BTN Assignment 2/8 BTN Keyset 98 DID RESTRICTION 99 DISA RESTRICTION 9* CALL RECORD ** AGENT LOGOUT *0 AGENT LOGIN *3 Blue Tooth REGISTER *4 Blue Tooth USAGE

Programming Manual 16 1.5 ADMIN PROGRAMMING INDEX MAIN MENU PGM ITEM PRE-PROGRAMMED DATABASE 100 Location Program 101 Rack Slot Assignment 102 WTIB Port number Assignment 103 Logical Slot Assignment 104 Numbering Plan Type 105 Flexible Number Plan – Station Number 106 Flexible Number Plan A 107 Flexible Number Plan B 108 IP Setting 109 Expanded Flexible Numbering Plan 250 Hot Desk Attributes STATION BASE PROGRAM 110 Station ID 111 Station Attribute I 112 Station Attribute II 113 Station Attribute III 114 ISDN Station Attribute 115 Flex Button Assignment 116 Station COS 117 CO Line Group Access 118 Internal Page Zone 119 Conference Page Zone 120 ICM Tenancy Group 121 Preset Call Forward 122 Hot/Warm Line Selection 123 CTI Station Attribute 124 SMDR Account Group 125 Copy DSS button 130 Display station number by COS 131 Display Station Number by CO access group CO LINE BASE PROGRAM 140 CO Service Type 141 CO Line Attribute I 142 CO Line Attribute II 143 ISDN CO Line Attribute I 144 CO Ring Assignment 145 CO Ring Assignment Display 146 ISDN CO Line Attribute II 147 CO MSN Mapping SLOT BASE PROGRAM 155 Slot Attribute SYSTEM BASE PROGRAM 160 System Attribute – I 161 System Attribute – II 162 Admin Password 163 Alarm Attributes 164 Attendant Assignment 165 Auto Attendant VMIB Annc. Assignment 166 CO-to-CO COS 167 DID/DISA Destination 168 External Control Contact

Programming Manual 17 169 LCD Date/Time/Language Display Mode 170 Modem 171 Music 172 PBX Access Code 173 PLA Priority Setting 174 RS-232C Port Setting 175 Print Port Selection 176 Pulse Dial Ratio MAIN MENU PGM ITEM SYSTEM BASE PROGRAM 177 SMDR Attributes 178 System Date/Time Setting 179 Linked Station Pairs Table 180 System Timers – I 181 System Timers – II 182 System Timers – III DCOB 186 DCOB System attribute 187 DCOB CO Line Attribute STATION GROUP 190 Station Group Assign 191 Station Group Attribute ISDN SYSTEM BASE PROGRAM 200 System ISDN Attributes 201 COLP Table 202 MSN Table 203 ISDN Attributes II (Aria-24 ONLY) TABLES 220 LCR Attributes 221 LCR – Leading Digit Table 222 LCR – Digit Modification Table 223 LCR Table Initialization 224 Toll Exception Table – Allow A (Entry no:01-30) Toll Exception Table – Deny A (Entry no:01-30) Toll Exception Table – Allow B (Entry no:01-30) Toll Exception Table – Deny B (Entry no:01-30) 225 Canned Toll Table –Allow (Entry no:01-10) Canned Toll Table –Deny (Entry no:01-10) 226 Emergency Code Table 227 Authorization Code Table 228 Customer Call Routing 229 Executive/Secretary Table 231 Flexible DID Table 232 System Speed Zone 233 Weekly Time Table 234 Voice Mail Dialing Table 235 Tie Routing Table 236 Mobile Extension NETWORKING 320 Networking Basic Attribute 321 Networking Supplementary Attribute 322 Networking CO Line Attribute 323 Networking Attendant Assignment 324 Networking Routing Table

Programming Manual 18 VOIB 340 VOIB IP Setting NATION SPECIFIC 400 DTIB Rx Gain Control 401 SLIB Rx Gain Control 402 SLIB12 Rx Gain Control 403 WTIB Rx Gain Control 404 ACOB Rx Gain Control 405 ACOB8 Rx Gain Control 406 DCOB Rx Gain Control 407 VMIB Rx Gain Control 408 DTMF Receiver Rx Gain Control 409 EXT Page Rx Gain Control MAIN MENU PGM ITEM NATION SPECIFIC 410 CPTU Rx Gain Control 411 Modem Rx Gain Control 412 Short SLIB Gain Control 413 Long SLIB Gain Control 414 Far SLIB Gain Control 415 Short ACO Gain Control 416 Long ACO Gain Control 420 System Tone Frequency 421 Differential Ring Frequency 422 Distinct CO Ring Frequency 423 ACNR Tone Cadence 425 Singular Table (Korea Only) INITIALIZATION (DB INIT) 450 Initialization PRINT DATABASE 451 Print Prot Database

Programming Manual 19 1.6 DEFAULT VALUES TABLE 1.6.1 LOCATION PROGRAM PGM BTN ITEM DEFAULT REMARK 100 1 Nation Code 61 Max 4 digits 2 Customer Site Name . Max 23 digits TABLE 1.6.2 RACK SLOT ASSIGNMENT PGM BTN ITEM RANGE DEFAULT REMARK 101 - Slot Assignment Refer to Note 2 Refer to Note 1 In case of PRIB assignment, it is possible to program logical port number. Note.1) If the DIP switch of the manual board detection (DIP Switch 8) is ON, system will detect the installed board type automatically. If the DIP switch 8 is OFF, the board type code must be entered at each slot. After manual Rack Slot assignment, user should reset the system manually. Note.2) Board Type Code Table: STA CODE COL CODE STA & COL CODE Etc CODE DTIB12 DTIB24 SLIB6 SLIB12 WTIB DSIB 11 12 13 14 15 18 PRIB BRIB LCOB4 LCOB8 CLCOB4 TLIB EMIB VOIB NPRIB NBRIB(8) NBRIB(4) 31 32 33 34 49 37 38 41 42(ARIA-130) 43(ARIA-130) 44(ARIA-130) STIB 51 VMIB MISB 61 71 TABLE 1.6.3 WTIB PORT NUMBER ASSIGNMENT PGM BTN ITEM RANGE DEFAULT REMARK ARIA- 300/600 ARIA-130 102 - WTIB Port Number Assignment 008 – 192 (Multiple of 8) 08-80 (Multiple of 8) 8 When ARIA-130 has one rack : 08-40

Programming Manual 20 TABLE 1.6.4 LOGICAL SLOT ASSIGNMENT PGM BTN ITEM DEFAULT REMARK 103 1 COL Board Refer to Note 2 STA Board Refer to Note 3 VMIB Not Assigned Note) If the DIP switch of the manual board detection DIP Switch 8) is ON, system will detect the logical slot assign in sequence as increase order automatically. If the DIP switch 8 is OFF, the logical slot assignment must be entered at each board type. After manual logical slot assignment, user should reset the system manually. TABLE 1.6.5 NUMBERING PLAN TYPE PGM BTN ITEM STA RANGE REMARK ARIA-300 ARIA-130 ARIA-600 104 3 Number Set Type 3 100 – 399 100 – 227 1000 – 1599

Programming Manual 21 TABLE 1.6.6 FLEXIBLE NUMBERING PLAN PGM BTN FIELD NUMBER SET3 REMARK 105 - Intercom Call 100 - 399 ARIA-300 100 - 227 ARIA-130 1000 - 1599 ARIA-600 106 1 Group Pilot Number 620 - 667 ARIA-300, ARIA-600 620 - 634 ARIA-130 2 Internal Page Zone #01 - #35 ARIA-300, ARIA-600 #01 - #15 ARIA-130 3 Internal All Call Page #5 4 Meet Me Page ## 5 External Page Zone 1 #6 6 External Page Zone 2 #7 7 External Page Zone 3 #8 8 External All Call Page #9 9 All Call Page (Int & Ext) #00 10 SMDR Account Code Enter 550 SLT 11 Flash Command to CO Line 551 SLT 12 Last Number Redial 552 SLT 13 DND (Toggle On/Off) 553 SLT 14 Call Forward 554 SLT 15 Speed Dial Programming 555 SLT 16 Message Wait/Callback Enable 556 17 Message Wait/Callback Return 557 SLT 18 Speed Dial Access 558 SLT 19 Cancel DND/FWD/Pre-MSG 559 SLT 20 System Hold 560 SLT 21 Forced Log-in 561 22 Forced Log-out 562 23 Programming Mode Enter Code 563 SLT 24 ACD Reroute 564

Programming Manual 22 PGM BTN FIELD NUMBER SET3 REMARK 107 1 Alarm Reset 565 2 Group Call Pickup ** 3 UCD DND 568 4 Night Answer 577 5 Call Parking Locations 601 – 619 ARIA-300, ARIA-600 601 – 610 ARIA-130 6 Direct Call Pickup *7 7 CO Group Access 801-872 ARIA-300, ARIA-600 801-824 ARIA-130 8 Individual CO Access 88001-88200 ARIA-300 8801-8840 ARIA-130 88001-88400 ARIA-600 9 Tie Routing Access 89xx-89xx XX = Nominated lines from 01 – 30 8901 - 8930 10 Retrieve Held CO Line 8* 11 Retrieve Held Individual CO Line 8#xxx ARIA-300, ARIA-600 8#xx ARIA-130 12 Access CO Line In the 1st available CO Group 9 13 Attendant Call 0 14 1st Door Open #*1 15 2nd Door Open #*2 16 3rd Door Open #*3 17 4th Door Open #*4 18 5th Door Open #*5 19 6th Door Open #*6 20 7th Door Open #*7 ARIA-300, ARIA-600 N/A ARIA-130 21 VM Message Waiting Enable *8 22 VM Message Waiting Disable *9

Programming Manual 23 TABLE 1.6.7 IP SETTING PG M BTN ITEM RANGE DEFAULT REMARK 108 1 IP Name Max 16 Skip : # 2 Server IP Address 12 Digits 3 CLI IP Address 12 Digits 4 Gateway Address 12 Digits 5 Subnet Mask 12 Digits 255.255.255.0 6 PPP Usage 1:ON 0:OFF ON TABLE 1.6.8 EXPANDED FLEXIBLE NUMBERING PLAN PGM BTN LCD DISPLAY Number Set 3 109 1 MCID REQUEST ENTER NEW # *0 2 RSG Door Open 1 *1 3 RSG Door Open 2 *2 4 Enter Conf Room *57 5 SLT Conf Page Join *58 6 Unsupervised Conf Tmr Extend *## TABLE 1.6.9 STATION ID ASSIGNMENT PGM BTN ITEM RANGE DEFAULT REMARK ARIA-300, ARIA-600 ARIA-130 110 1 ID 01-18 01-13 17(12): SLT-CID(FSK) 18(13): SLT- CID(DTMF) 2 DSS/DLS MAP – Associate STA STA # STA #

Programming Manual 24 TABLE 1.6.10 STATION ATTRIBUTE I/II/III PGM BTN ITEM RANGE DEFAULT REMARK 111 1 Auto Speaker Selection ON / OFF ON 2 Call Forward ON / OFF ON 3 DND ON / OFF ON 4 Data Line Security ON / OFF OFF 5 Howling Tone to SLT ON / OFF ON 6 ICM Box Signaling ON / OFF OFF 7 No Touch Answer ON / OFF ON 8 Page Access ON / OFF OFF 9 Ring Type 1 - 4 1 10 Speaker/Headset Ring SP/HEAD/ BOTH Speaker-Phone 11 Speaker Phone/Headset ON/OFF ON 12 VMIB Slot 0 - 2 (ARIA-300, ARIA-600) 0 - 1 (ARIA-130) 0 13 ICM Group 01 - 15 (ARIA- 300 ARIA-600) 01 - 05 (ARIA- 130) 01 14 Error Tone for TAD ON / OFF OFF 15 SLT Flash Drop ON / OFF OFF 16 Loop LCR Account Code ON / OFF OFF 17 VMIB Message Type FIFO/LILO OFF 18 Off-Net Call Forward EN/DIS EN 19 Forced HF Mode ON/OFF OFF 20 CID SLT CAS GA 00 – 20 05 21 CID SLT FSK GA 00 – 20 05 PGM BTN ITEM RANGE DEFAULT REMARK 112 1 CO Warning Tone ON / OFF OFF 2 Automatic Hold ON / OFF OFF STA2:ON 3 CO Call Time Restriction ON / OFF OFF 4 Ind CO Line Access EN/DIS ENABLE 5 CO Line Queuing EN/DIS ENABLE 6 CO PGM EN/DIS DISABLE 7 PLA EN/DIS ENABLE 8 Prepaid Call ON / OFF OFF 9 Speed Dial Access EN/DIS ENABLE 10 Two Way Record ON / OFF OFF 11 Fax Mode ON / OFF OFF 12 OFFNET Call Mode EXT/ALL ALL 13 UCD Grp Service ON / OFF OFF 14 Ring Grp Service ON / OFF OFF 15 Stop Camp On Tone EN/DIS DISABLE

Programming Manual 25 16 Line length Short/Long/ Far Short SAF only 17 MSG SCRL SPD 0-7 3 18 Block Back Call On/Off Off 19 I-Time RST On/Off Off 20 STA Account On/Off Off 21 CID Type 2 Service On/Off Off 22 Door Open ENABLE/ DISABLE DISABLE 23 Dummy Station On/Off Off PGM BTN ITEM RANGE DEFAULT REMARK 113 1 Admin EN/DIS DISABLE STA100 Enable 2 VMIB Access EN/DIS DISABLE 3 Group Listening EN/DIS DISABLE 4 Override Privilege EN/DIS DISABLE 5 SMDR Hidden Dialed Digits EN/DIS DISABLE 6 Voice Over EN/DIS DISABLE 7 Warm Line Hot Line / Warm Line Warm Line 8 DVU MSG Retrieve Password ON/OFF OFF 9 DVU MSG Retrieve Date/Time ON/OFF ON 10 Alarm Attribute ARIA-130 MPB MISB (ON/OFF) (ON/OFF) OFF OFF ARIA-300 MISB RAU1 RAU2 (ON/OFF) (ON/OFF) (ON/OFF) OFF OFF OFF Aria-600 LMUE RAU1 RAU2 (ON/OFF) (ON/OFF) (ON/OFF) OFF OFF OFF TABLE 1.6.11 ISDN STATION ATTRIBUTE PGM BTN ITEM RANGE DEFAULT REMARK 114 1 CLIP LCD Display ON / OFF ON 2 COLP LCD Display ON / OFF OFF 3 CLI / REDIRECT Display CLI/ REDIRECT CLI 4 CLI MSG Wait ON / OFF OFF 5 EXT or CO ATD ATD/EXT EXT 6 Keypad Facility KEYPAG/DTMF DTMF 7 Long/Short LONG/SHORT SHORT 8 CPN Type 0-2 0(Not used) 9 S0 Sub-address 0-2 0(Not used) 10 Reserved - - 11 CLI Name Display ON/OFF OFF

Programming Manual 26 12 ISDN CLI Station Number Max 4 digits Logical STA Number 13 Progress Indication ON / OFF OFF 14 ISDN CLIR ON / OFF OFF 15 ISDN COLR ON / OFF OFF 16 DID Restriction ON / OFF OFF 17 DID Call Wait ON/OFF OFF 18 CLI Type Long/Short Short 19 Long Station CLI 20 MSN Wait ON/OFF OFF TABLE 1.6.12 FLEXIBLE BUTTON ASSIGNMENT PGM BTN ITEM RANGE DEFAULT REMARK 115 01-44 Flex. Buttons Assignment BTN 01-44 01: User Button - Not programmed 02: {CO} Button 01-40 (ARIA-130) 001-200 (ARIA-300) 001-400(ARIA-600) 03: {CO Group} Button 01-24 (Aria-130) 01-72 (ARIA-300, ARIA-600) 04: {LOOP} Button - 05: {STA xxx} Button STA No. 06: STA PGM Button 11 - 99 07: {STA SPD xxx} Button STA SPD Bin No. 08: {SYS SPD xxxx} Button SYS SPD Bin No. 09: Num Pln Button Num Plan Code 10: Net DSS Button Assign. 11: MSN Number 12: Hunt Group Number TABLE 1.6.13 STATION BASE PROGRAM PGM BTN ITEM RANGE DEFAULT REMARK 116 1 Station COS : Day 1 - 9 1 2 Station COS : Night 1 - 9 1 117 CO Group Access 1 CO Line Group 01~24 01-24 2 CO Line Group 25~48 25-48 ARIA-130: N/A 3 CO Line Group 49~72 49-72 118 Internal Page Zone Access GRP 01 1 Internal Page Zone 01~24 ARIA-130 : 01-10 2 Internal Page Zone 25~30 ARIA-130: N/A

Programming Manual 27 119 1-5 Conference Page Zone Access 31 - 35 (ARIA-300, Aria-600) 11 - 15 (ARIA-130) 120 ICM Tenancy Group number 1 ICM Tenancy Group Attendant STA No. - 2 ICM Tenancy Access Group 01 - 15 (ARIA-300 Aria-600) 01 - 05 (ARIA-130) - 121 Preset Call Forward - PGM BTN ITEM RANGE DEFAULT REMARK 122 Hot Line / Warm Line - 1: Flex Button 01 – 44 - 2: CO Line 001-200 (ARIA-300) 01-40 (ARIA-130) 001-400 (Aria-600) - 3: CO Group 01-72 (ARIA-300, Aria-600) 01-24 (ARIA-130) - 4: Station STA No. - 123 1 CTI Mode 0 – 2 1 0: Inactive 1: CTI mode 2: AT mode 2 CTI Baud Rate 0 – 2 0 0: 1200 1: 2400 2: 4800 124 SMDR Account Group Assign 00 – 99(ARIA-300, Aria-600) 00 – 23(ARIA-130) 00(Not Assigned) TABLE 1.6.14 TABLE COPY DSS BUTTON PGM BTN ITEM RANGE DEFAULT REMARK 125 Copy DSS button F1 / F2 TABLE 1.6.15 DISPLAY STATION NUMBER BY COS PGM BTN ITEM RANGE DEFAULT REMARK 130 Display Station Number by COS F1 / F2 TABLE 1.6.16 DISPLAY STATION NUMBER BY CO ACCESSS PGM BTN ITEM RANGE DEFAULT REMARK 131 Display Station Number F1 / F2

Programming Manual 28 TABLE 1.6.17 CO LINE BASE PROGRAM PGM BTN ITEM RANGE DEFAULT REMARK 140 CO Service Type 1 CO Type 1-5 1(Normal) 1: Normal, 2: A_DID, 3: ISDN DID/MSN, 4: TIE, 5: DCO DID 2 Detailed Attribute of the type If CO Service type is Normal PGM BTN ITEM RANGE DEFAULT REMARK 140 1 CO Service Type 1-5 1 (Normal) 2 Detailed Attribute BTN DISA 1 Day DISA SVC ON /OFF OFF VMIB ANNC 00-70 00(NOT_ASG) 2 Night DISA SVC ON /OFF OFF VMIB ANNC 00-70 00(NOT_ASG) 3 W/end DISA SVC ON /OFF OFF VMIB ANNC 00-70 00(NOT_ASG) If CO Service type is ISDN DID/MSN, PGM BTN ITEM RANGE VALUE REMARK 140 1 CO Service Type 1-5 3 ISDN DID/MSN 2 Detailed Attribute No Attributes Required If CO Service type is TIE, PGM BTN ITEM RANGE VALUE REMARK 140 1 CO Service Type 1-5 4: TIE, 2 Detailed Attribute TIE Attribute

Programming Manual 29 TIE SIG 1-5 Not Assigned 1: RD 2: LD 3: EM-C 4: EM-D 5: EM-I PGM BTN ITEM RANGE DEFAULT REMARK 141 CO Line Attributes –I 1-9 1 CO Line Group Assignment 00-73 (ARIA-300, Aria-600) 00-25 (ARIA-130) 01 2 CO Line COS 1-5 1 3 DISA Account Code ON / OFF OFF 4 CO Line Assign POL/LOOP LOOP Polarity RV, Loop Start 5 CO Line Type PBX/CO CO 6 CO Line Signal Type DTMF/PULSE DTMF 7 Flash Type GROUND/LOOP LOOP 8 UNA ON / OFF OFF 9 CO Line Group Account ON / OFF OFF 10 Tenancy Group 00-15 (ARIA-300, Aria-600) 00-05 (ARIA-130) 01 PGM BTN ITEM RANGE DEFAULT REMARK 142 CO Line Attributes – II 1-13 1 CO Line Name Display ON / OFF OFF 2 CO Line Name Assign - Max 12 characters 3 Metering Unit 00-06 0 4 Line Drop using CPT ON / OFF OFF 5 CO Distinct Ring 0-4 0 6 CO Line MOH 0-13 (ARIA-300, Aria-600) 0-12 (ARIA-130) 1 7 PABX CO Dial Tone YES / NO YES 8 PABX CO Ring Back Tone YES / NO NO 9 PABX CO Error Tone YES / NO NO 10 PABX CO Busy Tone YES / NO NO 11 PABX CO Announce Tone YES / NO NO 12 CO Flash Timer 000 – 300 050 10 msec base 13 Open Loop Detect Timer 0 – 20 0 100 msec base 14 Line Length Not used in Australia South Africa ONLY 15 DISA ANS Timer 1-9 5

Programming Manual 30 PGM BTN ITEM RANGE DEFAULT REMARK 143 ISDN CO Line Attribute 1-6 1 COLP Table Index 00 ~ 50 None 00 ~ 49: PGM 201 Bin No. 50: PGM 114-BTN 5 2 CLIP Table Index 00 ~ 50 None 00 ~ 49: PGM 201 Bin No. 50: PGM 114-BTN 5 3 Type of Calling Number 0-4 2 0:Unknown number 1:International type 2:National number 3:Not used 4:Subscriber number 4 DID Conversion Type 0 ~ 2 0 5 DID Removal Number 00-99 00 00:Do not ignore 01-99:indicate an ignored called party number (DID_RN : DID Remove number from called party information) 6 ISDN Enblock Sending ON / OFF OFF ON:Enblock Sending Mode OFF:Overlap Sending Mode 7 CLI Transit ORI (1) CFW(0) CFW(0) ORI : Send CLI as the originate caller‟s CLI. CFW : Send CLI as the call forwarded station‟s CLI. 8 Numbering plan ID Flex 1: Calling 0 - 7 0 See Note Below: Flex 2: Called 0 - 7 0 9 ISDN – SS CD Enable / Disable DIS 10 ISDN 1 Digit Remove ON/OFF OFF ISDN incoming CPN is unknown-unknown case, the first 1 digit is removed. 11 ISDN CP INBAND ON / OFF OFF Note: 0 = Unknown 1 = ISDN/Telephony 2 = Not Used 3 = Data 4 = Telex 5 = Not Used 6 = National Standard 7 = Private

Programming Manual 31 PGM BTN ITEM RANGE DEFAULT REMARK 144 CO Ring Assignment STA Range (Delay : 0 – 9), Hunt Group, VMIB Message 1 Day STA_R/ HUNT/ VMIB 2 Night STA_R/ HUNT/ VMIB 3 Weekend STA_R/ HUNT/ VMIB 4 On-demand STA_R/ HUNT/ VMIB 145 CO Ring Assignment Display 1 Day 2 Night 3 Weekend 4 On-demand PGM BTN ITEM RANGE DEFAULT REMARK 146 1 Incoming Prefix Code Insertion ON / OFF OFF 2 Outgoing Prefix Code Insertion ON / OFF ON 3 A/u-Law Line Installed U/A A-Law ON: u-Law OFF: A-Law 4 Calling Sub-address ON/OFF OFF If this field is ON, station number will be filled in calling party number sub-address IE in setup. 5 DID Dgt Rec_Num. 2 – 4 3 6 DID Dgt Mask Max 4 digits #*** TABLE 1.6.18 CO MSN Mapping Table (Table removed from S/W version 2.2 Fi) PGM BTN ITEM RANGE DEFAULT REMARK 147 CO Mapping Table 000-249 -

Programming Manual 32 TABLE 1.6.19 ISDN CO BASE PROGRAM PGM BTN ITEM RANGE DEFAULT REMARK 160 System Attributes-I 1-13 1 Attendant Call Queuing RB RBT/MOH MOH RBT:Ring Back Tone MOH:PGM171 - 2 2 CAMP RBT/MOH RBT/MOH MOH 3 CO Line Choice LAST/ROUND LAST Round-Robin, Last Choice 4 DISA Retry Counter 1-9 3 5 ICM Continuous Dial-Tone CONT / DISCONT CONT Continuous, Discontinuous 6 CO Dial-Tone Detect ON / OFF OFF 7 External Night Ring ON / OFF OFF 8 Hold Preference SYS/EXEC SYS System, Exclusive 9 Multi-line Conference ON / OFF ON 10 Print LCR Conversion Digit ON / OFF OFF 11 Conference Warning Tone ON / OFF ON 12 Offnet Prompt Usage ON / OFF ON 13 Offnet DTMF Tone ON / OFF ON 14 CO Voice Path Connect IMM/DGT DGT 15 Transfer Tone RBT/MOH RBT 14 CO Voice Path Connect IMM/DGT DGT 15 Transfer Tone RBT/MOH MOH 16 CO-CO Xfer CPT Detect ON/OFF OFF 17 ACD info print ON/OFF OFF 18 Unsupv. Conf Tmr Extend ON/OFF OFF 161 System Attributes-II 1-13 1 Network Time/Date Setting ON / OFF OFF 2 Off-Hook Ring Signal Type MUTE/BURST MUTE Mute Ring, One Burst 3 Override 1st CO Group ON / OFF ON 4 Page Warning Tone ON / OFF ON 5 Privacy ON / OFF ON 6 Privacy Warning Tone ON / OFF ON 7 Single Ring for CO Call YES/NO NO 8 WTU Auto Release ON / OFF OFF 9 ACD PRNT Enable ON / OFF OFF ON:10s 10 ACD PRNT Timer 001 – 255 001 10 sec or 1 hour base 11 ACD Clr After Print ON / OFF OFF 12 VMIB PROMPT GAIN 00 - 31 08 13 VM with CLI Info ON / OFF OFF 14 ACD Print Timer Unit HOUR/SEC SEC SEC: 10 seconds 15 Set VM SMDI Type TYPE II/ TYPE I TYPE I 16 Incomming Call Toll Check ON/OFF OFF 17 Reserved

Programming Manual 33 18 No DSS indication EN/Dis Dis 19 UK Billing mode On/Off Off 162 - Admin Password 4 Digits - 163 1 Alarm Enable ON / OFF OFF 2 Alarm Contact Type CLOSE/OPEN CLOSE Close, Open 3 Alarm Mode ALARM / BELL ALARM Alarm, Door Bell 4 Alarm Signal Mode RPT/ONCE RPT Repeat , Once 164 1-5 Attendant Assignment STA No. 1 : 101 Max 5 Atds 165 - Auto Attendant 1 Auto Attendant Usage ON / OFF OFF 2 Auto Attendant VMIB Annc.# 00-70 00(not_asgn) PGM BTN ITEM RANGE DEFAULT REMARK 166 CO-to-CO COS 1-7 1 1 Day COS 1-7 1 2 Night/Weekend COS 1-7 1 167 DID/DISA Destination F1-F4 1 Busy Destination F1-F3 F1 1: Tone 2: ATD (Ring Assign) 3: FWD to Hunt Grp 2 Error Destination F1-F3 F1 3 No Answer Destination F1-F3 F1 4 VMIB PROMPT USAGE F1-F5 1- Busy Prompt Usage ON / OFF ON 2- Error Prompt Usage ON / OFF ON 3- DND Prompt Usage ON / OFF ON 4- No Ans Prompt Usage ON / OFF ON 5- Atd Xfer Prompt Usage ON / OFF ON 5 Reroute Busy Dest F1-F3 F1 1: Tone 2: ATD (Ring Asgn) 3: FWD to Hunt Grp 6 Reroute Error Dest F1-F3 F1 7 Reroute No Answer Dest F1-F3 F1 168 1 First Contact 1-5 - 1: LBC(STA #) 2: Door 3: Ext. 1 4: Ext. 2 5: Ext. 3 2 Second Contact 1-5 - 3 Third Contact 1-5 - 4 Forth Contact 1-5 - 5 Fifth Contact 1-5 - 6 Sixth Contact 1-5 - 7 Seventh Contact 1-5 - ARIA-300 Only 169 1 Time Display Mode 12H/ 24H 12H 2 Date Display Mode MMDD / DDMM DDMMYY

Programming Manual 34 3 Language Display Mode 00-14 12(Korean) 0:ENGLISH, 1:ITALIAN, 2:FINNISH, 3:DUTCH, 4:SWEDISH, 5:DANISH, 6:NORWEGIAN, 7:HEBREW, 8:GERMANY, 9:FRENCH, 10:PORTUGUESE, 11:SPANISH, 12:KOREAN, 13:ESTONIA, 14:RUSSIAN, PGM BTN ITEM RANGE DEFAULT REMARK 170 Modem Associated Device STA 227 (ARIA-130) STA 399 (ARIA-300) STA 1599 (Aria-600) Last Station 1 Associated Station Station Number 2 Associated CO CO Number PGM BTN ITEM RANGE DEFAULT REMARK 171 1 BGM Type 0-12 (ARIA-300, Aria-600) 0-11 (ARIA-130) 1 0: None 1: Int. Music 2-4: Ext. Music 1-3 5-6(7): VMIB 1-2(3) 7(8)-11(12): SLT MOH 2 MOH Type 0-13 (ARIA-300, Aria-600) 0-12 (ARIA-130) 1 0: NOT_ASG 1: Int. Music 2-4: Ext. Music 1-3 5-6(7): VMIB 1-2(3) 7(8)-11(12): SLT MOH 12(13): Hold Tone 3 ICM Box Music Channel 0-12 (ARIA-300, Aria-600) 0-11 (ARIA-130) 1 The same as above 4 Assign MOH via SLT Flex. 1-5 (+SLT STA No.) - SLT MOH 1-5 PGM BTN ITEM RANGE DEFAULT REMARK 172 1 - 4 PBX Access Code Max. 2 digits - Maximum 4 PBX access code 173 PLA Priority Setting PLA priority is set Exclusively 1 Transfer CO 1 – 4 1 2 Recalling CO 1 – 4 2 3 Incoming CO 1 – 4 3 4 Queued CO 1 – 4 4

Programming Manual 35 174 RS-232 PORT Setting 1 Baud Rate Setting 0-8 19200(6) 0: UNKNOWN 1: UNKNOWN 2: 1200 BAUD 3: 2400 BAUD 4: 4800 BAUD 5: 9600 BAUD 6: 19200 BAUD 7: 38400 BAUD 8: 57600 BAUD 2 CTS ON / OFF OFF 3 Page Break ON / OFF OFF 4 Line Page 001-199 060 PGM BTN ITEM RANGE DEFAULT REMARK 175 1 Off-line SMDR/Statistics Print 01-13 (ARIA-300, Aria-600) 01-11 (ARIA-130) COM2(02) : ARIA-300 COM1(01) : ARIA-130 Value : 1-8 : ARIA-300, Aria-600 Value : 1-6 : ARIA-130 2 Admin Print 3 Traffic Print 4 SMDI Print 5 CALL Info Print 6 On-line SMDR Print 7 Trace Print 8 Debug Print 9 PC_ADM NET_PCADM ARIA-300, Aria-600 :1-5, 9, 10 ARIA-130 : 1-3, 7, 8 10 PC_ATD NET_PCATD ARIA-300, Aria-600 : 1, 2, 4, 5, 11 ARIA-130 : 1, 2, 4, 9 11 CTI NET_CTI ARIA-300 , Aria-600 : 1, 2, 4, 5, 12 ARIA-130 : 1, 2, 4, 10 12 REMOTE_DIAG NET_REMOTE ARIA-300 , Aria-600: 1-5, 13 ARIA-130 : 1-3, 11 PGM BTN ITEM RANGE DEFAULT REMARK 176 - Pulse Dial/Speed Ratio 66/33 / 60/40 66/33 66/33 60/40(10 PPS only) 177 SMDR Attributes 1-14 1 SMDR Save Enable ON / OFF OFF 2 SMDR Print Enable ON / OFF OFF 3 SMDR Recording Call Type LD / ALL LD LD : Long Distance ALL: All

Programming Manual 36 4 SMDR Long Distance Call Digit Counter 07-15 07 Considered more than this value as Long Distance Call. 5 Print Incoming Call ON / OFF OFF 6 Print Lost Call ON / OFF OFF 7 Records in Detail ON / OFF ON 8 SMDR Dial Digit Hidden 0-9 0 9 SMDR Currency 3 English Chars - 10 SMDR Cost Per Unit Pulse 6 digits - 11 SMDR Fraction 0-5 0 12 SMDR Start Timer 0 – 250 0 1 sec base 13 SMDR Hidden Digit Right/Left Right 14 SMDR Long Distance Codes MAX 2 digits 0 Max. 5 LD codes PGM BTN ITEM RANGE DEFAULT REMARK 178 1 System Time Setting 4 digits - Hour/Min sequence 2 System Date Setting 6 digits - Month/Day/Year sequence. 179 1 View Show the linked pairs 2 Linked Pair Input 2 STA# Max: 64 pairs TABLE 1.6.20 SYSTEM TIMER PROGRAM PGM BTN ITEM RANGE DEFAULT REMARK 180 1 Attendant Recall Timer 00 - 60 01 1 min base 2 Call Park Recall Timer 000 - 600 120 1 sec base 3 Camp-on Recall Timer 000 - 200 030 1 sec base 4 Exclusive Hold Recall Timer 000 - 300 060 1 sec base 5 I-Hold Recall Timer 000 - 300 030 1 sec base 6 Sys Hold Recall Timer 000 - 300 030 1 sec base 7 Transfer Recall Timer 000 - 300 030 1 sec base 8 ACNR Delay Timer 000 - 300 030 1 sec base 9 ACNR No Answer Timer 10 - 50 30 1 sec base 10 ACNR Pause Timer 005 - 300 030 1 sec base 11 ACNR Retry Counter 01 - 30 3 12 ACNR No Tone Retry Counter 1 - 9 1 13 ACNR Tone Detect Timer 001-300 030 1 sec base 14 Automatic CO Release Timer. 020 - 300 030 1 sec base 15 CCR Inter-Digit Timer 000 - 255 030 100 msec base 16 CO Call Drop Warning Timer 00 - 99 10 1 sec base 17 CO Call Restriction Timer 00 - 99 0 1 min base 18 CO Dial Delay Timer 00 - 99 01 100 msec base 19 CO Release Guard Timer 001 - 150 020 100 msec base 20 CO Ring Off Timer 010 - 150 060 100 msec base

Programming Manual 37 21 CO Ring On Timer 1 - 9 2 100 msec base 22 CO Warning Tone Timer 060 - 900 180 1 sec base 181 1 Call FWD No Answer Timer 000 - 255 015 1 sec base 2 DID/DISA No Answer Timer 00 - 99 20 1 sec base 3 VMIB User Record Timer 010 - 255 020 1 sec base 4 VMIB Valid User Message Timer 0-9 4 1 sec base 5 Door Open Timer 05 - 99 20 100msec base 6 ICM Box Timer 00 - 60 30 1 sec base 7 ICM Dial Tone Timer 01 - 20 10 1 sec base 8 Inter Digit Timer 01 - 20 05 1 sec base 9 MSG Wait Reminder Tone Timer 00 - 60 00 1 min base 10 Paging Timeout Timer 000 - 255 015 1 sec base 11 Pause Timer 1 - 9 3 1 sec base 12 Preset Call Forward Timer 00 - 99 10 1 sec base 13 SLT DTMF Release Timer 00 - 20 00 1 sec base 14 3SOFT Auto RLS Timer 01-30 05 15 VM Pause Timer 01-90 30 (ms) 16 Transit connect timer 01-30 04 17 VMIB msg Rewind (sec) 01 – 99 … PGM BTN ITEM RANGE DEFAULT REMARK 182 1 SLT Hook Switch Bounce Timer 01 - 25 01 100msec base 2 SLT Maximum Hook Flash Timer 01-25 05 100msec base 3 SLT Minimum Hook Flash Timer 000 - 250 020 10msec base 4 SLT Ring Phase Timer 2 - 5 5 1 sec base 5 Station Auto Release Timer 020 - 300 060 1 sec base 6 Unsupervised Conference Timer 00 - 99 10 1 min base 7 Wake-Up Fail Ring Timer 00 - 99 20 1 sec base 8 Warm Line Timer 01 - 20 05 1 sec base 9 Wink Timer 010 - 200 010 10msec base 10 Enblock Digit timer 01-20 15 1 sec base 11 CCR Time Out Timer 000-300 015 1 sec base 12 DID Inter Digit Timer 01-20 03 1 sec base (PGM 185,186 and 187 Not avail in Australia) PGM BTN ITEM RANGE DEFAULT REMARK 185 CIDU Setting 1 CID Usage ON / OFF OFF 2 CID Name Display Name(1) / Telephone No.(0) Telephone No.(0) 3 Serial Port Select 1-4 - 4 CID/CO Line Port Mapping 000-063 - 5 Initialize CID Data

Programming Manual 38 TABLE 1.6.21 DCOB ATTRIBUTE PGM BTN ITEM RANGE DEFAULT REMARK 186 DCOB System Attributes 1-12 1 DCOB CO Type 0-2 2 0:Sweden/Cyprus 1:Italy 2:Korea/Australia 2 Metering Type 0-1 0 3 R2 OUT Manage Timer 01-50 14 1 sec 4 R2 IN Manage Timer 01-50 14 1 sec 5 R2 Disappear Timer 01-50 14 1 sec 6 R2 Pulse Timer 01-30 7 20 msec 7 R2 Ready Timer 000-500 7 20 msec 8 Dial Tone Delay Timer 01-30 20 9 Line Status 1-9 6 Free Line 10 Calling Category 1-9 1 User no priority 11 DNIS Service ON/OFF OFF 12 CLI Digit Num 01-10 4 Reserved 187 DCOB CO Line Attributes CO Line range 1 IN Digit Type 0-2 2 0:PULSE 1:DTMF 2 OUT Digit Type 0-2 2 2:R2MFC 3 CLI Digit Num 01-15 10 TABLE 1.6.22 STATION GROUP ASSIGNMENT PGM BTN ITEM RANGE DEFAULT REMARK 190 Station Group Number STA Grp # - 1 Group Type 0-6 0 0: Not Assign 4: Ring 1: Circular 5: VM 2: Terminal 6: Pick up 3: UCD 7: Net VM 2 Pick-up Attribute ON/OFF OFF 3 Member Assignment Not Assigned - Group type should be assigned TABLE 1.6.23 STATION GROUP PROGRAM PGM ITEM BTN SUB ITEM RANGE DEFAULT REMARK 191 Circular Group 1 VMIB Announce 1 Timer 000-999 015 1 sec base 2 VMIB Announce 2 Timer 000-999 000 1 sec base 3 VMIB Announce Location 1 00-70 00(not_asgn) 4 VMIB Announce Location 2 00-70 00(not_asgn)

Programming Manual 39 5 VMIB Announce 2 Repeat 000-999 000 1 sec base 6 VMIB Announce 2 Repeat E/D ON / OFF OFF 7 Overflow Destination STA #/HUNT#/ VMIB #/SYS SPD# - 8 Overflow Timer 000-600 180 1 sec base 9 Wrap-up Timer 002-999 002 1 sec base 10 No Answer Timer 00-99 15 1 sec base 11 Pilot Hunt ON / OFF ON 12 Alt If No Member ON / OFF OFF 13 Music Source 00 - 12 (ARIA-300) 00 - 11 (ARIA-130) 00 Terminal 1 VMIB Announce 1 Timer 000-999 015 1 sec base Group 2 VMIB Announce 2 Timer 000-999 000 1 sec base 3 VMIB Announce Location 1 00-70 00(not_asgn) 4 VMIB Announce Location 2 00-70 00(not_asgn) 5 VMIB Announce 2 Repeat 000-999 000 1 sec base 6 VMIB Announce 2 Repeat E/D ON / OFF OFF 7 Overflow Destination STA #/HUNT#/ VMIB #/SYS SPD# - 8 Overflow Timer 000-600 180 1 sec base 9 Wrap-up Timer 002-999 002 1 sec base 10 No Answer Timer 00-99 15 1 sec base 11 Pilot Hunt ON / OFF ON 12 Alt If No Member ON / OFF OFF 13 Music Source 00 - 12 (ARIA-300, Aria-600) 00 - 11 (ARIA-130) 00 PGM ITEM BTN SUB ITEM RANGE DEFAULT REMARK 191 UCD Group 1 VMIB Announce 1 Timer 000-999 015 1 sec base 2 VMIB Announce 2 Timer 000-999 000 1 sec base 3 VMIB Announce Location 1 00-70 00(not_asgn) 4 VMIB Announce Location 2 00-70 00(not_asgn) 5 VMIB Announce 2 Repeat 000-999 000 1 sec base 6 VMIB Announce 2 Repeat E/D ON / OFF OFF 7 Overflow Destination STA #/HUNT#/ VMIB #/SYS SPD# - 8 Overflow Timer 000-600 180 1 sec base 9 Wrap Up Timer 002-999 002 1 sec base 10 Alt If No Member ON / OFF OFF 11 Music Source 00 - 12 (ARIA-300, Aria-600) 00 - 11 (ARIA-130) 00 12 ACD Warning Tone ON / OFF ON 13 Alternate Destination STA #/ STA GRP# 14 Supervisor Timer 000-999 030 1 sec base

Programming Manual 40 15 Supervisor Call Count 00-99 00 16 ACD Queued Call ON / OFF OFF 17 MAX Que Call Count 00-99 00 18 Supervisor STA # - 19 UCD hunt Stations' Priority 0-9 0 For each member Ring Group 1 VMIB Announce 1 Timer 000-999 015 1 sec base 2 VMIB Announce 2 Timer 000-999 000 1 sec base 3 VMIB Announce Location 1 00-07 00(not_asgn) 4 VMIB Announce Location 2 00-07 00(not_asgn) 5 VMIB Announce 2 Repeat 000-999 000 1 sec base 6 VMIB Announce 2 Repeat E/D ON / OFF OFF 7 Overflow Destination STA #/HUNT#/ VMIB #/SYS SPD# - 8 Overflow Timer 000-600 180 1 sec base 9 Wrap Up Timer 002-999 002 1 sec base 10 Music Source 00 - 12 (ARIA-300, Aria-600) 00 - 11 (ARIA-130) 00 11 Max. Queued Call Count 00-99 00 PGM ITEM BTN SUB ITEM RANGE DEFAULT REMARK 191 VM Group 1 Wrap-up Timer 002-999 002 1 sec base 2 Put Mail Index 1-4 1 3 Get Mail Index 1-4 2 4 Hunt Type Cir/Term Term 5 SMDI Port 01-13 (ARIA-300, Aria-600) 01-11 (ARIA-130) 02(COM2) 01(COM1) 6 Overflow Timer 000-600 180 1 sec base 7 Overflow Destination STA #/HUNT#/ VMIB #/SYS SPD# - Pick-up Group 1 Auto Pick-up ON / OFF OFF 2 All Group Member Ringing ON / OFF OFF TABLE 1.6.24 ISDN ATTRIBUTES PGM BTN ITEM RANGE DEFAULT REMARK 200 1 Advice of Charge 0-5 0 0: Do not service AOC 1: Italy and Spain 2: Finland 3: Australia 4: Belgium 5: Standard 2 CO ATD Code Max 2 digits -

Programming Manual 41 3 Incoming Prefix Code Insertion ON / OFF OFF See PGM 146 for Aria-600 4 Outgoing Prefix Code Insertion ON / OFF ON See PGM 146 for Aria-600 5 A/u-Law Line Installed U/A A-Law See PGM 146 for Aria-600 ON: u-Law OFF: A-Law 6 CLI Print ON/OFF OFF 7 International Access Code Max 4 digits - 8 Calling Sub-address ON/OFF OFF See PGM 146 for Aria-600 If this field is ON, station number will be filled in calling party number sub-address IE in setup. 9 My Area Code Max 6 digits - 10 My Area Prefix Code Max 4 digits - 11 Maintain DID Name ON/OFF OFF 12 PC Application Dest STN Station 100 Station destination for remote ISDN CAPI access PGM BTN ITEM RANGE DEFAULT REMARK 201 - COLP Table Entry No. (00-49) - Max 10 digits 202 - MSN Table Entry No. (000-249) - 1 CO Line number 01-40 (ARIA-130) 001-200 (ARIA-300) 001-400(Aria-600) - 2 Index 000-999 - 3 SUB Number 0-9 - 4 MSN number 20 digits - 5 Block same MSN ON/OFF 203 1 TEI type Fixed/Auto Auto Aria-24 ONLY 2 Service Type Keypad/Functional Keypad Aria-24 ONLY 3 Hold Code Max. 10 digits *75# Aria-24 ONLY 4 Retrieve Code Max. 10 digits *76# Aria-24 ONLY

Programming Manual 42 TABLE 1.6.25 LCR TABLE ASSIGNMENT PGM BTN ITEM RANGE DEFAULT REMARK 220 1 LCR Access Mode M00/M01/M02/M11/M12/M13 M00 2 Set the Day of week zone 1234567 1 MON 1 – 3 1 2 TUE 1 – 3 1 3 WED 1 – 3 1 4 THUR 1 – 3 1 5 FRI 1 – 3 1 6 SAT 1 – 3 1 7 SUN 1 – 3 1 3 Set the Time Zone of Day zone 1 1 Time Zone1 00 – 24 0024 2 Time Zone2 00 – 24 - 3 Time Zone3 00 – 24 - 4 Set the Time Zone of Day zone 2 1 Time Zone1 00 – 24 0024 2 Time Zone2 00 – 24 - 3 Time Zone3 00 – 24 - 5 Set the Time Zone of Day zone 3 1 Time Zone1 00 – 24 0024 2 Time Zone2 00 – 24 - 3 Time Zone3 00 – 24 - PGM BTN ITEM RANGE DEFAULT REMARK 221 Leading Digit Table 000-249 1 LCR Type 1 – 3 3 1:int 2:col 3: both 2 Code (leading digit) Max 12 digits - 3 Day Zone 1 DMT 6digits Time1: 2digit 4 Day Zone 2 DMT 6digits Time2: 2digit 5 Day Zone 3 DMT 6digits Time3: 2digit 6 Check Password 1: ON 0: OFF OFF PGM BTN ITEM RANGE DEFAULT REMARK 222 Digit Modification Table 00-99 1 Added Digit Max 25 digits 2 Removal Position 1 – 12 1 3 Number Of Remove 1 – 12 0 4 Add Position 1 – 13 1 5 CO Group 1 – 72 (ARIA-300 Aria-600) 1 – 24 (ARIA-130) 1 6 Alt Index 0 – 99 - 223 LCR Table Initialization 1 DMT Of Day_zone_1 6 digits Time1: 2digit

Programming Manual 43 2 DMT Of Day_zone_2 6 digits Time2: 2digit 3 DMT Of Day_zone_3 6 digits Time3: 2digit 4 CO Grp Init 1 – 72 (ARIA-300, Aria-600) 1 – 24 (ARIA-130) 5 Alt Index Init 0 - 99 6 Init All LCR TABLE 1.6.26 TOLL TABLE ASSIGNMENT PGM BTN ITEM RANGE DEFAULT REMARK 224 Toll Table 1 Allow Table A (01-30) Max 14 digits - 2 Deny Table A (01-30) Max 14 digits - 3 Allow Table B (01-30) Max 14 digits - 4 Deny Table B (01-30) Max 14 digits - 5 Allow Table C (01-50) Max 14 digits - 6 Deny Table C (01-50) Max 14 digits - 7 Allow Table D (01-50) Max 14 digits - 8 Deny Table D (01-50) Max 14 digits - 225 Canned Toll Table 1 Allow Table (01-20) Max 14 digits - 2 Deny Table (01-20) Max 14 digits - 226 Emergency Code Table (01-10) Max 14 digits TABLE 1.6.27 OTHER TABLES PGM BTN ITEM RANGE DEFAULT REMARK 227 Author Code Table 001 - 600 (Aria-300) (Aria-600) 001 - 164 (ARIA-130) Table entry (001-600) Max 5 digits PGM BTN ITEM RANGE DEFAULT REMARK 228 CCR Table 1-70 01 Station STA # - 02 Hunt Group HUNT # - 03 VMIB Announce # - 04 VMIB Drop Announce # 05 System Speed 2000-3499 (ARIA-130) 2000-4999 (ARIA-300) 2000-6999(Aria-600) - 06 Internal Page 1 - 10 (ARIA-130) 1 - 30 (ARIA-300, Aria-600) - 07 External Page 1 – 3 -

Programming Manual 44 08 All Call Page 1 – 3 - 1:INT 2:EXT 3:All 09 Net Number Net Number 10 Conference Room 1-9 229 Exec/Sec Table 01-12 (ARIA-130) 01-36 (ARIA-300. Aria-600) Table entry(01-36) STA #/STA # PGM BTN ITEM RANGE DEFAULT REMARK 231 - Flexible DID Table Entry No.(000-999) - 1 DID Name Max 11 chars. - 2 Day Destination 1-10 - 01(sta), 02(hunt), 03(VMIB) 3 Night Destination 1-10 - 04(VMIB drop),0 5(spd), 4 Weekend Destination 1-10 - 06(int. page), 07(ext. page) 5 Reroute Destination 1-6 - 08(all page), 09(net call), 10(Conf Room) 232 System Speed Zone 01-10 1 Speed Bin Range in Zone 2200-3499 (ARIA-130) 2200-4999 (ARIA-300) 2000-6999(Aria-600) - 2 Station Range Station Range - 3 Toll Checking On/Off ON PGM BTN ITEM RANGE DEFAULT REMARK 233 Weekly Time Table 1 – 7 - Day of Week 1 Day Start Time 0000 – 2359 0900 2 Night Start Time 0000 – 2359 1800 3 Weekend Start Time 0000 – 2359 234 Voice Mail Dial-Table 1 - 9 1 Prefix Index 12 Digits - 2 Suffix Index 12 Digits - 235 TIE Line Routing Table CO number - 236 Mobile Extension Table 001– 600 001 – 300 001 – 128 (LDK-600) (LDK-300) (LDK-100) 1 Mobile Extension Enable ON/OFF OFF 2 Mobile Extension CO Grp. 1 – 72 1 – 24 (LDK-300/300E) (LDK-100) 3 Mobile Extension Tel No Max 24 250 Hot Desk Attributes 1 Number of Agent (000 – 300) 000 2 View Agent Range N/A … 3 Auto Logout Timer (hour) 00 – 24 00

Programming Manual 45 TABLE 1.6.28 NETWORKING ATTRIBUTE PGM BTN ITEM RANGE DEFAULT REMARK 320 Networking Basic Attributes F1-F7 1 Networking Enable ON / OFF OFF 2 Networking Retry Count 00 – 99 00 3 Networking CNIP Enable ON / OFF OFF 4 Networking CONP Enable ON / OFF OFF 5 Networking Signal Method FAC / UUS UUS 6 Networking CAS Enable ON / OFF OFF 7 Networking VPN Enable ON / OFF OFF 8 Net CC Retain Mode ON / OFF OFF Aria-600 only 321 Supplementary Attributes F1-F7 1 Networking Transfer Mode RERT / JOIN JOIN 2 TCP port 4 digits 9000 3 UDP port 4 digits 9001 4 Gatekeeper IP Address (BLF) 12 digits 0.0.0.0 5 Duration of BLF status 01 ~ 20 sec 02 6 Multicast IP Address 12 digits 0.0.0.0 7 Net Trans Recall Timer 1 ~ 300 10 322 Networking CO Line Attributes CO Line range 1 Networking CO Group 00 – 24 00 2 Networking CO Out Send ON / OFF OFF 3 Networking CO Out Trans ON / OFF OFF 323 CAS/VPN CO Group Assign F1-F3 1 CAS Number Table Index 00-71 00 2 VPN CO Group 00-71 00 3 CAS Prefix Code 8 digits - 324 Networking Routing Table 00-71 1 System Usage (0:NET / 1: PSTN) NET(0) 2 Numbering Plan Code 16 digits 3 Numbering Plan CO Group 00-24 - 4 CPN Information 16 digits - 5 Alternate Speed Bin 2000-4999 6 MPB LAN IP Address IP address - 7 Digit Repeat (0:NO/1:YES) -NO 8 CO ATD Code CLI YES/NO NO TABLE 1.6.29 VOIB NET ATTRUBUTE PGM BTN ITEM RANGE DEFAULT REMARK 340 VOIB IP SETTING F1-F3 (ARIA-300) F1-F2 (ARIA-130) VOIB NET SETTING F1-F5

Programming Manual 46 1 IP Addressing(SKIP:#) 2 GATEWAY Addressing (SKIP:#) 3 SUBNET Mask(SKIP:#) 4 DNS Addressing (SKIP:#) 5 TRACE Password Max 10 Digits 6 Default CODEC 1 – 4 1 7 Default GAIN 1 - 62 31 8 NO Delay (TOS) ON / OFF OFF 9 Throughput (TOS) HIGH / NORMAL NORMAL 10 Reliability (TOS) HIGH / NORMAL NORMAL PGM BTN ITEM RANGE DEFAULT REMARK 380 VOIB for RSG / IP (1 – 2) C.0Am 1 ….. …… …. 2 RSG/IP Channel Assignment / VOIB Slot Num (00 – 08) 00 381 RSG / IP NO ASSIGN 1 RSG L300:00-96 L130:00-32 08 2 IP Phone L300:00-96 L130:00-64 00 382 RSG / IP ATTRIBUTES 1 (1 – 7) 1 Transfer Mode MAC / IP IP 2 CASTING MODE MULTI / UNI UNI 3 TONE SOURCE LDK / REMOTE REMOTE 4 PEER TO PEER ON / OFF ON 0: G711 Alaw 5 CODEC TYPE 0 – 2 0 G711 Alaw 1: G711 Ulaw 6 FIRST ACCESS RSG CO ON / OFF ON 2: G723.1 7 RING W/O CO RING ASSIGN ON / OFF ON 383 RSGM ATTRIBUTES 1 (L300: 01-96; L130: 01-32) 1 ST MAC ADDERSS 00-00-00-00-00-00 2 IP ADDRESS DISP 0.0.0.0 3 PORT VIEW D(..) S(..) C(..) 4 PORT NUMBER 5 NAT IP ADDRESS DISP 0.0.0.0 6 NAT PORT NUMBER 7 STUN ENABLED NAT / PAT NONE 384 RSGM ATTRIBUTES 2 (L300: 01-96; L130: 01-32) 1 I MOH RTP PORT 8186 2 E MOH RTP PORT 8188 3 MOH TYPE MUSIC / H-TN H-TN 4 MUSIC SOURCE EXT /INT INT 5 EXT CONTACT 1 6 EXT CONTACT 2 7 ALARM ENABLE ON / OFF OFF 8 ALARM CONTACT CLOSE / OPEN CLOSE 9 ALARM MODE ALARM / BELL ALARM 10 ALARM SIGNAL RPT / ONCE RPT 11 CTI PORT SLT (0 – 2) NOT_USED 12 RSG NATION CODE 64 385 RSGM ALARM ATTRIBUTES 1 (STA RANGE) 1 SELECT RSG ALARM ZONE L300: F1-F4 L130: F1-F2 (NONE)

Programming Manual 47 386 IP PHONE ATTRIBUTES 1 (L300: 01-96; L130: 01-64) 1 SET MAC ADDRESS 00-00-00-00-00- 00 2 IP ADDRESS DISP 0.0.0.0 3 PORT VIEW 4 PORT NUMBER 5 NAT IP ADDRESS DISP 0.0.0.0 6 NAT PORT NUMBER 0 7 STUN ENABLED NAT / PAT NONE 8 CTI IP ADDRESS 0.0.0.0 390 RSGM_DKT RX GAIN C.0Am 1 DKTU 00 – 63 10 2 SLT 00 – 63 10 3 CTR SLT 00 – 63 08 4 WKT 00 – 63 10 5 ACO 00 – 63 32 6 CTR ACO 00 – 63 15 7 DCO 00 – 63 32 8 VMIB 00 – 63 32 9 DTMF 00 – 63 08 10 TONE 00 – 63 32 11 MUSIC 1 00 – 63 32 12 MUSIC 2 00 – 63 32 13 RSG DKT 00 – 63 10 14 RSG SLT 00 – 63 08 15 RSG LCO 00 – 63 15 16 IP PHONE 00 – 63 10 391 RSGM_DKT TX GAIN 1 DKTU 00 – 63 10 2 SLT 00 – 63 10 3 CTR SLT 00 – 63 31 4 WKT 00 – 63 10 5 ACO 00 – 63 32 6 CTR ACO 00 – 63 37 7 DCO 00 – 63 32 8 DVU 00 – 63 32 392 RSGM_SLT RX GAIN 1 DKTU 00 – 63 31 2 SLT 00 – 63 27 3 CTR SLT 00 – 63 23 4 WKT 00 – 63 31 5 ACO 00 – 63 49 6 CTR ACO 00 – 63 32 7 DCO 00 – 63 50 8 VMIB 00 – 63 53 9 DTMF 00 – 63 29 10 TONE 00 – 63 53 11 MUSIC 1 00 – 63 53 12 MUSIC 2 00 – 63 53 13 RSG DKT 00 – 63 31 14 RSG SLT 00 – 63 23

Programming Manual 48 15 RSG LCO 00 – 63 32 16 IP PHONE 00 – 63 31 393 RSGM_SLT TX GAIN 1 DKTU 00 – 63 08 2 SLT 00 – 63 07 3 CTR SLT 00 – 63 23 4 WKT 00 – 63 08 5 ACO 00 – 63 34 6 CTR ACO 00 – 63 24 7 DCO 00 – 63 29 8 DVU 00 – 63 23 394 RSGM_LCO RX GAIN 1 DKTU 00 – 63 37 2 SLT 00 – 63 33 3 CTR SLT 00 – 63 29 4 WKT 00 – 63 37 5 ACO 00 – 63 53 6 CTR ACO 00 – 63 38 7 DCO 00 – 63 37 8 VMIB 00 – 63 37 9 DTMF 00 – 63 26 10 TONE 00 – 63 37 11 MUSIC 1 00 – 63 53 12 MUSIC 2 00 – 63 53 13 RSG DKT 00 – 63 37 14 RSG SLT 00 – 63 29 15 RSG LCO 00 – 63 38 16 IP PHONE 00 – 63 37 395 RSGM_LCO TX GAIN 1 DKTU 00 – 63 15 2 SLT 00 – 63 11 3 CTR SLT 00 – 63 32 4 WKT 00 – 63 20 5 ACO 00 – 63 33 6 CTR ACO 00 – 63 38 7 DCO 00 – 63 14 8 DVU 00 – 63 23 396 IP PHONE RX GAIN 1 DKTU 00 – 63 10 2 SLT 00 – 63 10 3 CTR SLT 00 – 63 08 4 WKT 00 – 63 10 5 ACO 00 – 63 32 6 CTR ACO 00 – 63 15 7 DCO 00 – 63 32 8 VMIB 00 – 63 32 9 DTMF 00 – 63 08 10 TONE 00 – 63 32 11 MUSIC 1 00 – 63 32 12 MUSIC 2 00 – 63 32 13 RSG DKT 00 – 63 10 14 RSG SLT 00 – 63 08 15 RSG LCO 00 – 63 15

Programming Manual 49 16 IP PHONE 00 – 63 10 397 IP PHONE TX GAIN 1 DKTU 00 – 63 10 2 SLT 00 – 63 10 3 CTR SLT 00 – 63 31 4 WKT 00 – 63 10 5 ACO 00 – 63 32 6 CTR ACO 00 – 63 37 7 DCO 00 – 63 32 8 DVU 00 – 63 32 TABLE 1.6.30 NATION SPECIFIC PGM FLEX ITEM RANGE DEFAULT REMARK 400 DTIB RX Gain Korean version 1 DTIB/DKT 00 – 63 26 2 DTIB/SLT 00 – 63 33 3 DTIB/CTR SL 00 – 63 22 4 DTIB/WTU 00 – 63 26 5 DTIB/ACO 00 – 63 33 6 DTIB/CTR CO 00 – 63 22 7 DTIB/DCO 00 – 63 33 8 DTIB/VMIB 00 – 63 29 9 DTIB/DTMF 00 – 63 8 10 DTIB/TONE 00 – 63 32 11 DTIB/MUSIC1 00 – 63 29 12 DTIB/MUSIC2 00 – 63 29 13 DTIB/MUSIC3 00 – 63 29 PGM FLEX ITEM RANGE DEFAULT REMARK 401 SLIB RX Gain 1 SLIB/DKT 00 – 63 12 2 SLIB/SLT 00 – 63 23 ARIA-130 : Default 27 3 SLIB/CTR SL 00 – 63 12 ARIA-130 : Default 16 4 SLIB/WTU 00 – 63 12 5 SLIB/ACO 00 – 63 21 6 SLIB/CTR CO 00 – 63 12 7 SLIB/DCO 00 – 63 24 8 SLIB/VMIB 00 – 63 20 9 SLIB/DTMF 00 – 63 8 10 SLIB/TONE 00 – 63 18 11 SLIB/MUSIC1 00 – 63 20 12 SLIB/MUSIC2 00 – 63 20 13 SLIB/MUSIC3 00 – 63 20 PGM FLEX ITEM RANGE DEFAULT REMARK

Programming Manual 50 402 CTR SLIB RX Gain 1 CTRSL2/DKT 00 – 63 32 2 CTRSL2/SLT 00 – 63 43 ARIA-130 : Default 47 3 CTRSL2/ CTR SL 00 – 63 32 ARIA-130 : Default 36 4 CTRSL2/WTU 00 – 63 32 5 CTRSL2/ACO 00 – 63 41 6 CTRSL2/ATR CO 00 – 63 32 7 CTRSL2/DCO 00 – 63 44 8 CTRSL2/VMIB 00 – 63 40 9 CTRSL2/DTMF 00 – 63 28 10 CTRSL2/TONE 00 – 63 38 11 CTRSL2/MUSIC1 00 – 63 40 12 CTRSL2/MUSIC2 00 – 63 40 13 CTRSL2/MUSIC3 00 – 63 40

Programming Manual 51 PGM FLEX ITEM RANGE DEFAULT REMARK 403 WTIB RX Gain 1 WTIB/DKT 00 – 63 26 2 WTIB/SLT 00 – 63 33 3 WTIB/CTR SL 00 – 63 22 4 WTIB/WTU 00 – 63 26 5 WTIB/ACO 00 – 63 38 6 WTIB/CTR CO 00 – 63 29 7 WTIB/DCO 00 – 63 33 8 WTIB/VMIB 00 – 63 29 9 WTIB/DTMF 00 – 63 8 10 WTIB/TONE 00 – 63 37 11 WTIB/MUSIC1 00 – 63 29 12 WTIB/MUSIC2 00 – 63 29 13 WTIB/MUSIC3 00 – 63 29 PGM FLEX ITEM RANGE DEFAULT REMARK 404 ACOB RX Gain 1 ACOB/DKT 00 – 63 26 2 ACOB/SLT 00 – 63 37 3 ACOB/CTR SL 00 – 63 27 4 ACOB/WTU 00 – 63 26 5 ACOB/ACO 00 – 63 36 6 ACOB/STR CO 00 – 63 27 7 ACOB/DCO 00 – 63 33 8 ACOB/VMIB 00 – 63 32 9 ACOB/DTMF 00 – 63 32 10 ACOB/TONE 00 – 63 32 11 ACOB/MUSIC1 00 – 63 32 12 ACOB/MUSIC2 00 – 63 32 13 ACOB/MUSIC3 00 – 63 32 14 ACOB/MODEM 00 – 63 37 PGM FLEX ITEM RANGE DEFAULT REMARK 405 CTR ACOB RX Gain 1 CTRCO8/DKT 00 – 63 28 2 CTRCO8/SLT 00 – 63 43 3 CTRCO8/CTR SL 00 – 63 32 4 CTRCO8/WTU 00 – 63 31 5 CTRCO8/ACO 00 – 63 41 6 CTRCO8/CTR CO 00 – 63 32 7 CTRCO8/DCO 00 – 63 38 8 CTRCO8/VMIB 00 – 63 37 9 CTRCO8/DTMF 00 – 63 37 10 CTRCO8/TONE 00 – 63 37 11 CTRCO8/MUSIC1 00 – 63 37 12 CTRCO8/MUSIC2 00 – 63 37 13 CTRCO8/MUSIC3 00 – 63 37 14 CTRCO8/MODEM 00 – 63 44

Programming Manual 52 PGM FLEX ITEM RANGE DEFAULT REMARK 406 DCOB RX Gain 1 DCOB/DKT 00 – 63 26 2 DCOB/SLT 00 – 63 37 3 DCOB/CTR SL 00 – 63 26 4 DCOB/WTU 00 – 63 26 5 DCOB/ACO 00 – 63 24 6 DCOB/CTR CO 00 – 63 15 7 DCOB/DCO 00 – 63 32 8 DCOB/VMIB 00 – 63 32 9 DCOB/DTMF 00 – 63 32 10 DCOB/TONE 00 – 63 32 11 DCOB/MUSIC1 00 – 63 32 12 DCOB/MUSIC2 00 – 63 32 13 DCOB/MUSIC3 00 – 63 32 14 DCOB/MODEM 00 – 63 37 PGM FLEX ITEM RANGE DEFAULT REMARK 407 VMIB RX Gain 1 VMIB/DKT 00 – 63 21 2 VMIB/SLT 00 – 63 32 3 VMIB/CTR SL 00 – 63 21 4 VMIB/WTU 00 – 63 26 5 VMIB/ACO 00 – 63 32 6 VMIB/CTR CO 00 – 63 23 7 VMIB/DCO 00 – 63 32 8 VMIB/MUSIC1 00 – 63 32 9 VMIB/MUSIC2 00 – 63 32 PGM FLEX ITEM RANGE DEFAULT REMARK 408 DTMF RC Gain 1 DTMF/SLT 00 – 63 28 2 DTMF/CTR SL 00 – 63 17 3 DTMF/ACO 00 – 63 24 4 DTMF/CTR CO 00 – 63 15 5 DTMF/DCO 00 – 63 24 PGM FLEX ITEM RANGE DEFAULT REMARK 409 EXT PAGE Gain 1 EXT PAGE/DKT 00 – 63 26 2 EXT PAGE/SLT 00 – 63 37 3 EXT PAGE/CTR SL 00 – 63 26 4 EXT PAGE/WTU 00 – 63 26 5 EXT PAGE/ACO 00 – 63 37 6 EXT PAGE/CTR CO 00 – 63 28 7 EXT PAGE/DCO 00 – 63 37 8 EXT PAGE/VMIB 00 – 63 37 9 EXT PAGE/MUSIC1 00 – 63 37 10 EXT PAGE/MUSIC2 00 – 63 37 11 EXT PAGE/MUSIC3 00 – 63 37

Programming Manual 53 PGM FLEX ITEM RANGE DEFAULT REMARK 410 CPT Gain 1 CPT/ACO 00 – 63 24 2 CPT/CTR CO 00 – 63 15 3 CPT/DCO 00 – 63 24 PGM FLEX ITEM RANGE DEFAULT REMARK 411 MODEM Gain 1 MODEM/ACO 00 – 63 24 2 MODEM/CTR CO 00 – 63 20 3 MODEM/DCO 00 – 63 24 PGM FLEX ITEM RANGE DEFAULT REMARK 412 Short SLIB Gain Not for Australia 1 Shot ACO 00 – 63 31 SAF only 2 Long ACO 00 – 63 31 413 Long SLIB Gain Not for Australia 1 Shot ACO 00 – 63 37 SAF only 2 Long ACO 00 – 63 37 414 Far SLIB Gain Not for Australia 1 Shot ACO 00 – 63 45 SAF only 2 Long ACO 00 – 63 45 415 Short ACO Gain Not for Australia 1 Short SLIB 00 – 63 35 2 Long SLIB 00 – 63 41 SAF only 3 Far SLIB 00 – 63 47 416 Long ACO Gain Not for Australia 1 Short SLIB 00 – 63 39 2 Long SLIB 00 – 63 45 SAF only 3 Far SLIB 00 – 63 51 PGM FLEX ITEM RANGE DEFAULT REMARK 420 System Tone Frequency 1 Dial Tone 4digits 0425, 0000 2 Ring Back Tone 4digits 0425, 0000 3 Busy Tone 4digits 0425, 0000 4 Error Tone 4digits 0620, 000 5 Dummy Dial Tone 4digits 0350, 440 421 Differential Ring Frequency 1 Ring 1 4digits 1000, 1020 2 Ring 2 4digits 0890, 0910 3 Ring 3 4digits 1260, 1280 4 Ring 4 4digits 0800, 0820

Programming Manual 54 PGM FLEX ITEM RANGE DEFAULT REMARK 422 Distinct Ring Frequency 1 Ring 1 4digits 0480, 0000 2 Ring 2 4digits 0400, 0000 3 Ring 3 4digits 0620, 0000 4 Ring 4 4digits 0770, 0000 423 ACNR Tone Cadence 1 Ring-Back Tone 0-255 050, 100 20msec base 2 Busy Tone 0-255 025, 025 20msec base 3 Error Tone 0-255 012, 012 20msec base 4 S –Dial Tone 0-255 070, 000 20msec base TABLE 1.6.31 INITIALIZATION PGM FLEX ITEM RANGE DEFAULT REMARK 450 Initialization 1 Flexible Numbering Plan Initialization 2 Station Database Initialization 3 CO Line Database Initialization 4 System Feature Database Initialization 5 Station Group Database Initialization 6 ISDN Tables Database Initialization 7 Reserved Reserved 8 System Timer Database Initialization 9 Toll Table Database Initialization 10 LCR Database Initialization 11 Tables Initialization 12 Flexible Button Program Initialization 13 Networking Database Initialization 14 All Database Initialization 15 System Reset By Software

Programming Manual 55 TABLE 1.6.32 PRINT PROT DATABASE PGM FLEX ITEM RANGE DEFAULT REMARK 451 Print Prot Data 1 Flexible Numbering Plan Print 2 Station Database Print STN_R 3 CO Line Database Print CO_R 4 System Feature Database Print 5 Station Group Database Print 6 ISDN Tables Database Print 7 System Timer Database Print 8 Toll Table Database Print 9 LCR Database Print 10 Other Tables Print 11 Nation Specific Database Print 12 Flexible Button Program Print STN_R 13 Print Network Data 14 All Database Print 15 LCD Message Print 1 Language 00 – 12 Nation specific 00:ENG 12:KOR 2 Station Type 0 – 2 0 0: NORMAL 1: LG-GAP 2: LARGE 16 Quit Print

Programming Manual 56 2 PRE-PROGRAMMED DATABASE This section describes the pre-programming of the data. When installed, user must program some database (Ex. Nationality, Numbering Plan Type, and Slot Assignment) first, otherwise system may not operate properly. If you want to change nationality of the system, then use PGM 100. To assign the board in each rack, proceed PGM 101-102. After assigning rack slot, you must adjust PGM 103, Logical Slot Assignment. If you want to use the station number range flexibly, you can select a proper numbering plan type at PGM 104. If you want to change station numbers or feature codes, then use PGM 105~107. If you need more than 4 digits as a station number for VPN or QSIG, use the station prefix code at PGM 200-BTN 1. PROCEDURE FOR PRE-PROGRAMMING Initial Installation  Install all printed circuit boards into their correct positions.  Ensure that the lithium battery switch on the MPB is ON (Aria-300/600 = SW 2; Aria-130 = SW 1)  Ensure that MPB DIP SW 8 = ON  Power up the system following the following sequence: - Aria-300/600 - KSU 6/5/4/3/2/1; Aria-130 KSU 2/1.  Aria-130/300/600 will boot up and auto detect all of the installed boards  Set the nationality code – PGM 100 flex 1, dial 61 for Australia + [HOLD / SAVE]  Reset system – press the reset on the MPB or PGM 450 flex 15 + [HOLD / SAVE]  Switch MPB DIP SW 8 = OFF (to save the customer database on reset or power down)  Initialise all database PGM 450 flex 14 + [HOLD / SAVE] Adding a PCB to a working system Refer to the manual slot assignment method in ATIB-011.

Programming Manual 57 2.1 LOCATION PROGRAM (PGM 100) PROCEDURE LOCATION PROGRAM PRESS FLEX_KEY (1-2) (1) [TRANS/PGM] + 100. NATION CODE 82 (2) Press Flex. BTN 1~2. (Ex. Press Flex. BTN 1) LCD shows default or saved value of NATION CODE. Enter desired nation code in the TABLE 2.1.2. To save the changed nation code in memory, press the [HOLD/SAVE] button. LOCATION PROGRAM PRESS FLEX_KEY (1-2) (3) Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN ITEM RANGE DEFAULT REMARK 1 Nation Code 82 Max 2 digits 2 Site Name - Max 23 digits (Refer to English Character Set Table 2.1.3) TABLE 2.1.1 Location Program (PGM 100) NATION CODE Australia 61 TABLE 2.1.2 Nation & National Code (PGM 100) Q – 11 Z – 12 . – 13 1 – 10 A - 21 B - 22 C - 23 2 - 20 D - 31 E - 32 F - 33 3 - 30 G – 41 H - 42 I - 43 4 – 40 J - 51 K - 52 L - 53 5 - 50 M - 61 N - 62 O - 63 6 - 60 P - 71 R - 72 S - 73 Q - 7* 7 – 70 T - 81 U - 82 V - 83 8 - 80 W - 91 X - 92 Y - 93 Z - 9# 9 - 90 *1 - Blank *2 - : *3 - , 0-00 # TABLE 2.1.3 English Character Set

Programming Manual 58 2.2 RACK SLOT ASSIGNMENT (PGM 101) Rack slot assignment can be performed automatically and manually. If the DIP switch of the manual board detection is ON, system will detect the installed board type automatically. If the DIP switch is OFF, the board type code should be entered at each slot. After manual rack slot assignment, user must reset the system manually. To change the number of WTIB channels, program PGM102(WTIB port number assign) and reset manually. PROCEDURE BOARD ASSIGNMENT ENTER SLOT NUMBER (1) [TRANS/PGM] + 101 SLOT 01 (F1:ID F2:DEVS) ID : DTIB12 DEVS: 12 (2) To program the slot assignment, dial 2 digits as a slot number. If the slot is already assigned, related message will be displayed on the LCD. SLOT 01 (F1:ID F2:DEVS) ID : SLIB6 DEVS: 6 (3) To change pre-assigned board, press Flex BTN 1 and dial 2 digits as the board type code. Refer to Table 2.2.1 for each board type code. Then entered board type code will be displayed on the LCD. SLOT 01 (F1:ID F2:DEVS) ID : PRIB DEVS: 30 Cf.) In case of PRIB, logical port assign is possible. To program a logical port number, after entering board type code, press BTN 2 and dial 2 digits as logical port number between 01 and maximum board port capacity. If logical port is not entered, maximum port will be assigned .(After programming logical port number, program PGM 103.) SLOT 01 (F1:ID F2:DEVS) ID : PRIB DEVS: 30 (4) Press the [HOLD/SAVE] button for saving database permanently. BOARD ASSIGNMENT ENTER SLOT NUMBER  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. STA CODE COL CODE STA & COL CODE Etc CODE DTIB12 DTIB24 SLIB6 SLIB12 WTIB DSIB 11 12 13 14 15 18 PRIB BRIB LCOB4 LCOB8 CLCOB4 TLIB EMIB VOIB NPRIB NBRIB(8) NBRIB(4) 31 32 33 34 49 37 38 41 42(ARIA-130) 43(ARIA-130) 44(ARIA-130) STIB 51 VMIB MISB 61 71 TABLE 2.2.1 Board Type Code Table (PGM 101)

Programming Manual 59 2.3 WTIB PORT NUMBER ASSIGNMENT (PGM 102) This procedure determines the number of registrable wireless terminals. The available number of wireless terminal is 008-192 for ARIA-300 and Aria-600. 08-80 (08-40 for 1 rack) for ARIA-130. Default value is 008. PROCEDURE WTIB PORT NO (008–192) 008 (MULTIPLE OF 8) (1) [TRANS/PGM] + 102. In ARIA-130, (008-192) will be like (08- 80). If ARIA-130 has only one rack, it will be like (08-40). (2) Press the number of registrable wireless terminals. The number should be in the available range, and be the multiple of 8. WTIB PORT NO (008–192) 032 (MULTIPLE OF 8) (3) Press the [HOLD/SAVE] button for updating database permanently. 2.4 LOGICAL SLOT ASSIGNMENT (PGM 103) Logical slot assignment can be performed automatically and manually. If the DIP switch of the manual board detection is ON, system will detect the logical slot assign in sequence as increase order automatically. If the DIP switch is OFF, the logical slot assignment should be entered at each board type. After manual logical slot assignment, user must reset the system manually. For the VMIB, it is impossible to make logical slot assignment. So user must assign the VMIB slot number manually. In case of WTIB it is detected as one board by logical slot assignment. So you must assign just one slot number regardless of the number of installed WTIBs. PROCEDURE LOGICAL SLOT ASSIGN COL STA VMIB (1) [TRANS/PGM] + 103 02 03 .. .. .. .. .. .. .. .. .. .. .. .. .. .. (2) Press BTN regarding the slot type and dial slot numbers with increasing order for logical slot numbers. 02 03 05 07 .. .. .. .. .. .. .. .. .. .. .. .. (3) Press the [HOLD/SAVE] button for saving database permanently.  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN ITEM DEFAULT REMARK 1 COL Board - DIP Switch OFF: Manual slot assignment DIP Switch ON: Automatic slot assignment 2 STA Board - DIP Switch OFF: Manual slot assignment DIP Switch ON: Automatic slot assignment 3 VMIB - Should be programmed manually TABLE 2.4.1 Button Configuration for Slot Assignment (PGM 103)

Programming Manual 60 2.5 NUMBERING PLAN TYPE (PGM 104) PROCEDURE NUMBERING PLAN (1-8) 1 (1) [TRANS/PGM] + 104. NUMBERING PLAN (1-8) 2 (2) To assign the numbering plan type, press one digit between 1- 8. NUMBERING PLAN (1-8) 2 (3) Press the [HOLD/SAVE] button for saving database permanently. BTN ITEM STA RANGE DEFAUL T REMARK ARIA-300 ARIA-130 ARIA-600 3 Number Set Type 3 100 – 399 100 – 227 1000 – 1599 No Number Set 3 for Australia TABLE 2.5.1 Flexible Numbering Plan (PGM 104)

Programming Manual 61 2.6 FLEXIBLE NUMBERING PLAN (PGM 105) You can change each station number in this field. Station number of the system can be assigned flexibly via the system programming. Station Numbering Code length should be in the range of 2 digits through 4 digits. PROCEDURE 000 001 002 003 100 101 102 103 (1) [TRANS/PGM] + 105. 000 001 002 003 100 101 102 103  Station Number Assign. You will see the 4 station numbers corresponding to the 4 port numbers. Station number length is in the range of 2 digits through 4 digits. There are two methods for changing station number. Dial two station numbers - Range start station number & range end station number, then LCD shows dialed range value. Press the [HOLD/SAVE] button, then station numbers changed from the first station number on current LCD to range end (All LEDs of BTNs are off.). Press one of BTN 1-4 (Each BTN 1-4 is assigned to station number 1- 4 on the current LCD), then LED of pressed Flex button is steady on. Dial new station number and press the [HOLD/SAVE] button, or press other Flex button to assign station number to other station without saving (The LED of pressed Flex. button is on.). If you want to delete all station numbers, press the [SPEED] button and press [HOLD/SAVE] button, then all station numbers are cleared. If you want to change next 4 station numbers then press [▼] button. If you want to change previous 4 station numbers, then press [▲] button. 000 001 002 003 100 400 102 103 (2) Press the [HOLD/SAVE] button for saving database permanently. (Ex: Press Flex. BTN 2, dial 400 and press [HOLD/SAVE] button.)

Programming Manual 62 2.7 FLEXIBLE NUMBERING PLAN (PGM 106-107) Feature codes of the system can be assigned flexibly via the system programming. Feature Code length should be in the range of 1(one) digit through 4 digits. Let's say that a feature code conflict has occurred in such a case that a feature code string matches with other longer feature code string, checking from the first digit of the code. For example, features Code 53 and 536 have a feature code conflict. The system will not allow any feature code conflict. PROCEDURE FLEX NUMBERING PLAN A PRESS FLEX KEY (01-24) (1) [TRANS/PGM] + 106. You can program the 24 Flex. Numbers. Table 2.7.1 illustrates the programmable list of the 24 flexible Numbering plan used by PGM 106 and Table 2.7.2 illustrates the list for PGM 107. STA GRP PILOT NUMBER START & END #(620-667) (2) To change a numbering plan, press the related flexible button. Each code length is in 1~4 digits.(To enter station range, 2 ~ 8 digits) For example, press Flex. BTN 1 to change Station Group pilot number. In ARIA-130, the LCD display will be different with the left. see below table for more. Dial the first station group pilot number and last station group pilot number, and press the [HOLD/SAVE] button. Then you can see the changed station group pilot numbers on the LCD. If you press other Flex. BTN, you can assign other numbering plan. STA GRP PILOT NUMBER START & END #(620-667) (3) If you want to save all changed flexible numbers to system memory, press the [HOLD/SAVE] button. There are no errors in the Flexible Numbers, then confirmation tone will be heard. If some errors are detected, then error tone will be heard without updating system memory.

Programming Manual 63 PGM BTN LCD DISPLAY ITEM 106 1 STA GRP PILOT NUMBER START & END #(620-667) : ARIA-300, Aria-600 STA GRP PILOT NUMBER START & END #(620-634) : ARIA-130 Station Group Pilot Number 2 INT PAGE ZONES START & END #(#01-#35) : ARIA-300, Aria-600 INT PAGE ZONES START & END #(#01-#15) : ARIA-130 Internal Page Zone Number 3 INT ALL CALL ENTER NEW #(#5) Internal All Call Page 4 MEET ME PAGE ENTER NEW #(##) Meet Me Page 5 EXT PAGE ZONE 1 ENTER NEW #(#6) External Page Zone - 1 6 EXT PAGE ZONE 2 ENTER NEW #(#7) External Page Zone - 2 7 EXT PAGE ZONE 3 ENTER NEW #(#8) External Page Zone - 3 8 EXT ALL CALL ENTER NEW #(#9) External All Call Page 9 ALL CALL PAGE ENTER NEW #(#00) All Call Page (Internal/External) 10 SMDR ACT CODE ENTER ENTER NEW #(550) SMDR Account Code Enter 11 FLASH CMD TO CO ENTER NEW #(551) Flash Command to CO Line 12 SLT LAST SPD DIAL ENTER NEW #(552) Last Number Redial (LNR) 13 DND ENTER NEW #(553) Do-Not-Disturb 14 CALL FWD ENTER NEW #(554) Call Forward 15 SPD DIAL PGM ENTER NEW #(555) Speed Dial Program 16 MSG WAIT ENABLE ENTER NEW #(556) MSG Wait/Call-Back Enable 17 MSG WAIT RETURN ENTER NEW #(557) MSG Wait/Call-Back Answer 18 SPD DIAL ACCESS ENTER NEW #(558) Speed Dial Access 19 DND/FWD CANCEL ENTER NEW #(559) Cancel DND/CFW/Pre-selected MSG Features 20 SYSTEM HOLD ENTER NEW #(560) System Hold 21 FORCED LOG IN ENTER NEW #(561) 22 FORCED LOG OUT ENTER NEW #(562) 23 SLT PGM MODE ENTER ENTER NEW #(563) SLT Program Mode Select 24 ACD REROUTE ENTER NEW #(564) ACD Reroute TABLE 2.7.1 Flex Numbering Plan A (PGM 106)

Programming Manual 64 PGM BTN LCD DISPLAY ITEM 107 1 ALARM RESET ENTER NEW #(565) Alarm Reset 2 GROUP CALL PKUP ENTER NEW # ( ) Group Call Pick-Up 3 UCD DND ENTER NEW #(568) UCD Group DND 4 NIGHT ANSWER ENTER NEW #(577) Night Answer 5 CALL PARK LOCATIONS START & END #(601-619) : ARIA-300 Aria-600 CALL PARK LOCATIONS START & END #(601-610) : ARIA-130 Call Park Locations 6 DIRECT CALL PKUP ENTER NEW #(7) Direct Call Pick-Up 7 ACCESS CO GROUP FEAT START & END #(801-872): ARIA-300 Aria-600 ACCESS CO GROUP FEAT START & END #(801-824): ARIA-130 Access CO Group 8 ACCESS IND CO FEAT START&END #(88001-88200) : ARIA-300 START&END #(88001-88400) Aria-600 START&END #(8801-8840) : ARIA-130 Access Individual CO Line 9 TIE ROUTING ACCESS ENTER NEW #(8901) Tie Routing Access 10 ACCESS HELD CO FEAT ENTER NEW #(8*) Access Held CO Group 11 ACCESS HELD IND CO FEAT START&END # (8#001- 8#200) ACCESS HELD IND CO FEAT START&END # (8#01- 8#40) Access Held Individual CO Line 12 ACCESS CO IN 1ST CO GRP ENTER NEW #(9) Access to CO line in the 1st available CO Group 13 ATTENDANT CALL ENTER NEW #(0) Attendant Call 14 DOOR OPEN 1 ENTER NEW #(#*1) Door Open – 1 15 DOOR OPEN 2 ENTER NEW #(#*2) Door Open – 2 16 DOOR OPEN 3 ENTER NEW #(#*3) Door Open – 3 17 DOOR OPEN 4 ENTER NEW #(#*4) Door Open – 4 18 DOOR OPEN 5 ENTER NEW #(#*5) Door Open – 5 19 DOOR OPEN 6 ENTER NEW #(#*6) Door Open – 6 20 DOOR OPEN 7 ENTER NEW #(#*7) Door Open – 7 : ARIA-300, Aria-600 Only 21 VM MSG WAIT ENABLE ENTER NEW #(*8) VM MSG Wait Enable 22 VM MSG WAIT CANCEL ENTER NEW #(*9) VM MSG Wait Cancel TABLE 2.7.2 Flex Numbering Plan B (PGM 107)

Programming Manual 65 2.8 IP SETTING (PGM 108) IP address, Subnet mask, and GW address should be programmed for trace, remote upgrade, PC Admin, PC Attendant, etc via network. PROCEDURE IP NET SETTING PRESS FLEX_KEY (1-5) (1) [TRANS/PGM] + 108. IP NAME LGICKEYPHONE  For IP Name assignment, press Flex BTN 1, and enter the character. SERVER IP ADDR(SKIP:#) 165.147. 3. 1  For Server IP assignment, press Flex BTN 2, and enter the 12 digit.  To skip entering digit, press # button. SERVER IP ADDR(SKIP:#) 165.147. 3. 1 (2) Press the [HOLD/SAVE] button for saving database permanently. IP NET SETTING PRESS FLEX_KEY (1-5)  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN ITEM INTERCOM RANGE DEFAULT REMARK 1 IP Name 16 Chars - IP Name 2 Server IP Address 12 Digits - Sever Address 3 CLI IP Address 12 Digits - CLI IP Address 4 Gateway Address 12 Digits - Gateway Address 5 Subnet mask 12 Digits - 6 PPP Usage ON/OFF OFF TABLE 2.8.1 IP Setting (PGM 108)

Programming Manual 66 2.9 EXPANDED FLEXIBLE NUMBERING PLAN (PGM 109) To serve the expanded flexible numbering plan from PGM106 & 107, PGM 109 is added. PROCEDURE FLEX NUMBERING PLAN C PRESS FLEX KEY (01-01) [TRANS/PGM] + 109. You can program the 1 Flex. Numbers. Table 2.9.1 illustrates the programmable list of the 1 flexible Numbering plan used by PGM 109. MCID REQUEST ENTER NEW #(*0) To change a numbering plan, press the related flexible button. If you press other Flex. BTN, you can assign other numbering plan. MCID REQUEST ENTER NEW #(*0) If you want to save all changed flexible numbers to system memory, press the [HOLD/SAVE] button. There are no errors in the Flexible Numbers, then confirmation tone will be heard. If some errors are detected, then error tone will be heard without updating system memory. BTN LCD DISPLAY ITEM 1 MCID REQUEST ENTER NEW # : *0 ISDN supplementary service - Malicious Caller ID request 2 RSG DOOR OPEN 1 ENTER NEW # : *1 This can be activated from RSG stations on his RSG 3 RSG DOOR OPEN 2 ENTER NEW # : *2 4 CONF ROOM ENTER NEW # : 57 5 SLT CONF PAGE JOIN ENTER NEW # : 58 6 US-CONF TMR EXTENSION ENTER NEW # : ## Expanded Flexible Numbering Plan (PGM 109)

Programming Manual 67 2.10 HOTDESK AGENT ATTRIBUTE (PGM 250) PROCEDURE HOTDESK ATTRIBUTE PRESS FLEX (1-3) (1) [TRANS/PGM] + 250. To program, use the Flex. BTN as Table2.10.1. Press Flex. BTN 1-3 for setting each value. After pressing one flex BTN, the revised value can be set by entered digit NO OF AGENT (000-300) … (2) Enter the number of hot desk agent. NO OF AGENT (000-300) 050 (3) Press the [HOLD/SAVE] button for updating database permanently. BTN LCD DISPLAY ITEM 1 NO of Agent Assign number of agent 2 View Assigned Station Number of Agent View assigned station number for agents. 3 Auto Logout Timer Automatic logout after this timer. TABLE 2.10.1 Expanded Flexible Numbering Plan (PGM 250)

Programming Manual 68 3 STATION PROGRAMMING If station features are to be changed, press the [TRANS/PGM] button and dial 110-124 in Admin Programming mode. When programming, LCD and LEDs indicate current programmed data and programming status. If the programmer enters correct data, then LCD and LED's show the entered data and the data is stored in the temporary buffer area. To save data permanently, press the [HOLD/SAVE] button, then all data in the temporary buffer (same as LCD/LED's status) are stored into system memory. 3.1 STATION ID (PGM 110) When the system is initialized, all the stations‟ ID will be assigned to default value as Table 3.1.3. PROCEDURE STATION ID ASSIGN ENTER STA RANGE (1) [TRANS/PGM] + 110. (F1: ID F2 :ASC) DKTU (2) Enter station range (Ex. 100-110). LCD shows the station range. First press the 1st Flex. BTN and dial two digits to choose type of the station as Table 3.1.1. Note: DSS Map Type is only valid with the Flex. BTN 2. (F1: ID F2 :ASC) SLT (DTMF) (3) Dial digit 12(07 for ARIA-130), and SLT (DTMF) will be assigned to the selected station range. Press the [HOLD/SAVE] button for updating database permanently. (F1: ID F2 :ASC) DSS MAP2 : STA . . . . (4) In case of DSS Map type, enter the station range (Ex. 110-110) in the step (1). At first press the 1st Flex. BTN and enter 2-digit (Ex. 03: DSS Map 2) and press the [HOLD/SAVE] button for updating database. Next, press the 2nd Flex. BTN to assign the associating station number. Enter the station number and press the [HOLD/SAVE] button for updating database permanently. Note: When identifying a station as a DSS, you must enter the station number of the key station the DSS is associated with, not station number that the DSS is using. See also TABLE 3.1.2 for DSS default button configuration.

Programming Manual 69 DGT ARIA-300, Aria-600 ARIA-130 ITEM FLEX KEY 2 ITEM FLEX KEY 2 1 DKTU Invalid DKTU Invalid 2 DSS MAP 1 Associated STA No. DSS MAP 1 Associated STA No. 3 DSS MAP 2 Associated STA No. DSS MAP 2 Associated STA No. 4 DSS MAP 3 Associated STA No. DSS MAP 3 Associated STA No. 5 DSS MAP 4 Associated STA No. ICM BOX Invalid 6 DSS MAP 5 Associated STA No. WHTU Invalid 7 DSS MAP 6 Associated STA No. SLT (DTMF) Invalid 8 DSS MAP 7 Associated STA No. SLT (PULSE) Invalid 9 DSS MAP 8 Associated STA No. SLT with MSG Wait Lamp for DTMF Invalid 10 ICM BOX Invalid SLT with MSG Wait Lamp for Pulse Invalid 11 WHTU Invalid ISDN phone Invalid 12 SLT (DTMF) Invalid 13 SLT (PULSE) Invalid 14 SLT with MSG Wait Lamp for DTMF Invalid 15 SLT with MSG Wait Lamp for Pulse Invalid 16 ISDN phone Invalid TABLE 3.1.1 Button Configuration for Station ID (PGM 110) ITEM DEFAULT REMARK DSS/DLS MAP 1 First 12 Buttons Button 1 : Intrusion Button 2 : All Call Page Button 3 : Call Park 01 Button 4 : Station Group 1 Button 5 : Camp-On Button 6 : Internal All Call Page Button 7 : Call Park 02 Button 8 : Station Group 2 Button 9 : Grp Call Pickup Button 10 : External All Call Page Button 11 : Call Park 03 Button 12 : Station Group 3 DSS/DLS MAP 2 Station Ports 136 – 183 DSS/DLS MAP 3 Station Ports 184 – 231 (184-227 for ARIA-130) DSS/DLS MAP 4 Station Ports 232 – 279 ARIA-300 And ARIA-600 Only DSS/DLS MAP 5 Station Ports 280 – 327 DSS/DLS MAP 6 CO Line 01 – 48 DSS/DLS MAP 7 CO Line 49 – 96 DSS/DLS MAP 8 CO Line 97 – 144 TABLE 3.1.2 Initial Button Configurations for DSS/DLS Map (PGM 110)

Programming Manual 70 DGT ARIA-300, Aria-600 ARIA-130 ITEM DEFAULT ID ITEM DEFAULT ID 1 DKTU DKTU DKTU DKTU 2 DSS MAP 1 DKTU DSS MAP 1 DKTU 3 DSS MAP 2 DKTU DSS MAP 2 DKTU 4 DSS MAP 3 DKTU DSS MAP 3 DKTU 5 DSS MAP 4 DKTU ICM BOX ICM BOX 6 DSS MAP 5 DKTU WHTU WHTU 7 DSS MAP 6 DKTU SLT (DTMF) SLT (DTMF) 8 DSS MAP 7 DKTU SLT (PULSE) SLT (DTMF) 9 DSS MAP 8 DKTU SLT with MSG Wait Lamp for DTMF SLT (DTMF) 10 ICM BOX ICM BOX SLT with MSG Wait Lamp for Pulse SLT (DTMF) 11 WHTU WHTU ISDN Phone ISDN 12 SLT (DTMF) SLT (DTMF) 13 SLT (PULSE) SLT (DTMF) 14 SLT with MSG Wait Lamp for DTMF SLT (DTMF) 15 SLT with MSG Wait Lamp for Pulse SLT (DTMF) 16 ISDN Phone ISDN TABLE 3.1.3 Default Value of Station ID (PGM 110)

Programming Manual 71 3.2 STATION ATTRIBUTE – I (PGM 111) PROCEDURE STATION ATT 1 ENTER STA RANGE (1) [TRANS/PGM] + 111. 100-110 STATION ATT 1 PRESS FLEX_KEY (01-16) (2) Enter station range (Ex. 100-110). (3) To program, use the Flex. BTN as Table 3.2.1. Press Flex. BTN 1-15 for setting each value. After pressing one flex BTN, the revised value can be set by entered digit. 100-110 AUTO SPKER (1 : ON / 0 : OFF) : ON Ex) When pressing Flex. BTN 1, „Auto Speaker Selection‟ attribute value will be displayed. 100-110 AUTO SPKER (1 : ON / 0 : OFF) : OFF User can change value by pressing digit 0. LCD shows the changed attribute value. 100-110 AUTO SPKER (1 : ON / 0 : OFF) : OFF (4) Press the [HOLD/SAVE] button for updating database permanently. STATION ATT 1 PRESS FLEX KEY (01-19)  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN ITEM RANGE DEFAULT REMARK 1 Auto Speaker Selection ON/OFF ON Allowance to access a CO line or place a DSS call by pressing appropriate {CO} or {DSS} button without lifting handset or pressing the [MON] button. 2 Call Forward ON/OFF ON Enables Call Forward to be activated by the station. 3 DND ON/OFF ON Enables DND to be activated by the station. 4 Data Line Security ON/OFF OFF The allowance to protect from override and camp- on, when busy state. 5 Howling Tone to SLT ON/OFF ON The allowance to give howling tone to SLT 6 ICM Box Signaling ON/OFF OFF The allowance to receive ICM box signal. 7 No Touch Answer ON/OFF ON The allowance to connect the transferred CO line automatically when station mode is H/P. 8 Page Access ON/OFF OFF Allows access to paging by the station. 9 Ring Type 0 – 4 0 The station can give own ring type signal to another station in system through this field calling party centric. 10 Speaker Ring (1:S /2:H /3:BOTH) SPKR Station rings through Speaker, Headset or Both (speaker and headset). 11 Speakerphone ON/OFF ON Operate with speakerphone. 12 VMIB Slot 0-2 0 Assign VMIB logical slot with station base 13 ICM Group 01-15 (ARIA-300/600) 01-05 (ARIA-130) 01 Assign ICM Tenancy Group which is belonged to the station 14 Error Tone for TAD ON/OFF OFF With Answering Device instead of SLT, busy tone will be provided instead of error tone.

Programming Manual 72 BTN ITEM RANGE DEFAULT REMARK 15 SLT Flash Drop ON/OFF OFF In SLT, Pressing [FLASH] Key or Hook Flashing will drop the CO Call 16 Loop LCR Account Code ON/OFF OFF Check Account Code at Loop LCR 16 Loop LCR Account Code ON/OFF OFF Check Account Code at Loop LCR 17 VMIB Message Type FIFO/LIFO LIFO Priority to play VMIB message 18 Off-net Call Forward EN/DIS EN The possibility to enable/disable Off-net call forward 19 Forced HF Mode ON/OFF OFF A user with this feature turned ON is authorized to change a called party DKTU to hand-free mode. TABLE 3.2.1 Button Configuration (PGM 111) 3.3 STATION ATTRIBUTE - II (PGM 112) PROCEDURE STATION ATT 2 ENTER STA RANGE (1) [TRANS/PGM] + 112. 100-110 STATION ATT 2 PRESS FLEX_KEY (01-23) (2) Enter station range (Ex. 100-110). (3) To program, use the BTN as TABLE 3.3.1. Press Flex. BTN 1- 23 for setting each value. After pressing a Flex. BTN, the revised value can be set by entered digit. 100-110 CO WARN TN (1 : ON/ 0 : OFF ) : OFF Ex) When pressing Flex. BTN 1, „CO Warning Tone‟ attribute value will be displayed. 100-110 CO WARN TN (1 : ON/ 0 : OFF ) : ON  User can change value by pressing digit 1. LCD shows the changed attribute value. 100-110 CO WARN TN (1 : ON/ 0 : OFF ) : ON (4) Press the [HOLD/SAVE] button for updating database permanently. STATION ATT 2 PRESS FLEX_KEY (01-23)  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory.

Programming Manual 73 BTN ITEM RANGE DEFAULT REMARK 1 CO Warning Tone ON/OFF OFF The allowance to receive warning tone in order to remind the call elapse time in case of outgoing CO line conversation. (PGM 180-BTN 22) 2 Automatic Hold ON/OFF OFF While on a CO line, the station user seizes another CO line by depressing the {CO} button. The first CO line goes on hold automatically. (STA2: ON) 3 CO Call Time Restriction ON/OFF OFF If this flag is set to YES, station's outgoing CO call may be disconnected when CO call restriction timer (PGM 180-BTN 17) expires. 4 Ind CO Line Access ENABLE /DISABLE ENABLE The allowance to access individual CO line by dialing. 5 CO Line Queuing ENABLE /DISABLE ENABLE The allowance of queuing for a busy CO/group of lines. 6 CO PGM ENABLE /DISABLE DISABLE Determines that each station user can program CO button or not. 7 PLA ENABLE /DISABLE ENABLE The allowance to answer calls by simply lifting handset or pressing the [MON] button with the answering priority. (PGM173) 8 Prepaid Call ON/OFF OFF The allowance to use Prepaid CO Call feature. (Refer to PGM 180-BTN 16) 9 Speed Dial Access ENABLE /DISABLE ENABLE Allows access to system speed dial by the station. 10 Two-way Record ON/OFF OFF During incoming or outgoing Call, user can record the conversation. 11 Fax Mode ON/OFF OFF In Fax mode, single ring is provided and Attendant recall is not operated. 12 Off-net Call Mode EXT/ALL ALL ALL: Internal Off-net Call Fwd and External Off-net Call Fwd are allowed. EXT: External Off-net Call Fwd is only allowed 13 UCD Group Service ON/OFF OFF When DID/DISA call destination is STA, ON: ring to UCD Grp which the station belongs to. OFF: ring to the station. 14 Ring Group Service ON/OFF OFF When DID/DISA call destination is STA, ON: ring to Ring Grp which the station belongs to. OFF: ring to the station. 15 Stop Camp-on Tone ENABLE /DISABLE DISABLE Make Camp on Tone not to be heard. 16 Line Length Short/Long/ far Short N / A For Australia (South Africa only) 17 MSG SCRL SPD 0 - 7 3 Scroll speed for SMS or broadcasting notice message. (Only for LKD-30DH) 18 Block Back Call ON/OFF OFF If this value is ON, SLT recalling is blocked after pressing [FLASH] button. 19 I-Time RST ON/OFF OFF If this value is ON, the conversation time of incoming CO call is limited. 20 STA Account ON/OFF OFF If this value is ON, an authorized code is required when accessing a CO line. 21 CID Type 2 Service ON/OFF OFF If this value is ON, CLI Type 2 service applies for CID SLT. 22 Door Open ENABLE/ DISABLE DISABLE If this value is ON, the station can open the door using the door open code. 23 Dummy Station ON/OFF OFF Set ON to define this station as a Dummy Station for Hot-Desk use.

Programming Manual 74 TABLE 3.3.1 Button Configuration (PGM 112)

Programming Manual 75 3.4 STATION ATTRIBUTE - III (PGM 113) PROCEDURE STATION ATT 3 ENTER STA RANGE (1) [TRANS/PGM] + 113. 100-110 STATION ATT 3 PRESS FLEX_KEY (1-10) (2) Enter station range (Ex. 100-110). (3) To program, use the BTN as Table 3.4.1. Press flex BTN 1-10 for setting each value. After pressing one flex BTN, the revised values can be set by input digit. 100-110 ADMIN (1 : EN/ 0 : DIS ) : DISABLE Ex) Pressing Flex. BTN 1, „ADMIN‟ attribute value will be displayed on the LCD. 100-110 ADMIN (1 : EN/ 0 : DIS ) : ENABLE  User can select value by pressing digit 1, LCD shows the changed attribute value. 100-110 ADMIN (1 : EN/ 0 : DIS ) : ENABLE (4) Press the [HOLD/SAVE] button for updating database permanently. STATION ATT 3 PRESS FLEX KEY (1-10)  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory.

Programming Manual 76 BTN ITEM RANGE DEFAULT REMARK 1 Admin ENABLE /DISABLE DISABLE The allowance the station to program Admin Database. This feature is available at only DKTU. (STA 100 : Enable as default) 2 VMIB Access ENABLE /DISABLE DISABLE The allowance to access Digital Voice Unit. 3 Group Listening ENABLE /DISABLE DISABLE The allowance to use group listening (While you are talking on handset, by pressing the [MON] button, other people around you may hear the conversation through the speaker of the keyset.). 4 Override Privilege ENABLE /DISABLE DISABLE The allowance to override CO line to gain access to the conversation. 5 SMDR Hidden Dialed Digits ENABLE /DISABLE DISABLE The allowance to hide CO dialing number on SMDR printing. 6 Voice Over ENABLE /DISABLE DISABLE The allowance to use Voice Over feature 7 Warm Line HOT/WRM WARM This field is determined that Warm Line (OFF) or Hot Line (ON) in PGM 122. 8 DVU MSG Retrieve Password ON/OFF OFF When retrieving DVU Message, User must enter password or not 9 DVU MSG Retrieve Date/Time ON/OFF ON When retrieving DVU Message, Date and time will be heard or not 10 Alarm Attribute Flex BTN 1 ON/OFF OFF Alarm MISB (ARIA-300, Aria-600) Alarm MPB (ARIA-130) Flex BTN 2 ON/OFF OFF Alarm RAU Contact 1 (ARIA-300, Aria-600) Alarm MISB (ARIA-130) Flex BTN 3 ON/OFF OFF Alarm RAU Contact 2 : ARIA-300 Aria-600 TABLE 3.4.1 Button Configuration - III (PGM 113)

Programming Manual 77 3.5 ISDN STATION ATTRIBUTE (PGM 114) PROCEDURE STATION ATT 4 ENTER STA RANGE (1) [TRANS/PGM] + 114. 100-110 STATION ATT 4 PRESS FLEX_KEY (01-20) (2) Enter station range (Ex. 100-110). (3) To program, use the BTN as Table 3.5.1. Press Flex. BTN 1- 20 for setting each value. After pressing a Flex. BTN, the revised value can be set by input digit. 100-110 CLIP DISP (1 : ON / 0 : OFF ) : OFF Ex) Pressing Flex. BTN 1, „CLIP LCD Display‟ attribute value will be displayed. 100-110 CLIP DISP (1 : ON / 0 : OFF ) : ON User can change value by pressing digit 1, LCD shows the changed attribute value. 100-110 CLIP DISP (1 : ON / 0 : OFF ) : ON (4) Press the [HOLD/SAVE] button for updating database permanently. STATION ATT 4 PRESS FLEX_KEY (01-20  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN ITEM RANGE DEFAULT REMARK 1 CLIP LCD Display ON/OFF ON This field is determined that a station displays CLIP or not. 2 COLP LCD Display ON/OFF OFF This field is determined that a station displays COLP or not. 3 CLI / Redirect Display RED/CLI CLI To select original CLI or redirected CLI. ON: Original CLI, OFF: Redirected CLI 4 CLI MSG Wait ON/OFF OFF This field is determined that a station receives CO message wait or not. ON:YES, OFF:NO 5 EXT or CO ATD ATD/EXT EXT To select EXT(extension number) or CO ATD to make outgoing CLI or COLP information 6 Keypad Facility KEYPAD /DTMF DTMF This field determines that ISDN station sends digit in DTMF or keypad facility after connected. 7 Long/Short LONG /SHORT SHORT This field determines that ISDN station acts in Short passive mode or not.

Programming Manual 78 BTN ITEM RANGE DEFAULT REMARK 8 CPN Type 0-2 0 This field indicates how the CPN IE is filled in SETUP message. 0: Do not send CPN (Called Party Number) to S0. In this case, all S0 STAs of the S port will be ringing. 1: Send station number as CPN 2: Bypass CPN from the network. (In the case of 1 & 2, only one specific STA will be ringing) 9 S0 Sub Address 0-2 0 This field indicates how the sub-address used in SETUP message. 0: Station sub-address not used. 1: Sub-address is filled in the CPN field of SETUP message. 2: Sub-address is filled in the CPSN (Called Party Sub- address Number) field of SETUP. 10 Reserved - - - 11 CLI Name Display ON/OFF OFF If this field is ON, the system checks whether the received CLI is matched with the speed dial data or not. If it is matched, the speed dial name is displayed. 12 ISDN CLI STA Max. 4 digit Logical STA No. If outgoing CLI is active and CLI type is EXT, this field used when making outgoing CLI. 13 Progress Indication ON/OFF OFF If this field ON and a SLT seizes an ISDN line, the progress indication IE indicating the originator is non- ISDN device is made in SETUP message. 14 ISDN CLIR ON/OFF OFF If this field is ON, the system will not send CLI information and restrict PX send it. 15 ISDN COLR ON/OFF OFF If this field is ON, the system will not send COLI information and restrict PX send it. 16 DID Restriction ON/OFF OFF Restrict the DID Call. 17 DID Call Wait ON/OFF OFF New DID call waiting indicate. 18 CLI Type LNG/SRT SRT Long: Use station CLI with PGM114-BTN19. (max 12) Short: Use station CLI with PGM114-BTN12 (max 4) 19 Long Station CLI Max 12 digit Logical STA No. If outgoing CLI is active and CLI type is EXT, this field used when making outgoing CLI. 20 MSN Call Wait ON/OFF OFF Turn ON for this station to receive a MSN Call Wait TABLE 3.5.1 Button Configuration for ISDN Station Attributes (PGM 114)

Programming Manual 79 3.6 FLEX BUTTON ASSIGNMENT (PGM 115) Each Flex. Button in a key station can be assigned identified as one of the followings; No. Type RANGE REMARK ARIA-300 ARIA-130 Aria-600 01 User Button - - - User can program by button programming procedure. (empty) 02 {CO xx} Button 001 – 200 01 – 40 001 – 400 CO Line 03 {CO Grp xx} 01 – 72 01 – 24 01 – 72 CO Group 04 {LOOP} 05 {STAxxxx} 100 – 399 100 – 227 100 – 1599 Station No. 06 STA PGM Button 11 – 99 11 – 99 11 – 99 07 {STA SPDxx} 00 – 99 00 – 99 00 – 99 Station Speed Bin 08 {SYS SPDxxxx} 2000 –4999 2000 –3499 2000 –6999 System Speed Bin 09 Num Pln Button Num Plan Code 10 Net DSS Button When using Networking feature 11 MSN Button MSN Number MSN Number TABLE 3.6.1 Button Type for Flexible Button Assignment (PGM 115) PROCEDURE FLEX BUTTON ASSIGN ENTER STA RANGE (1) [TRANS/PGM] + 115. SELECT BTN RANGE D1:F01-F24 D2:F25-F48 Enter station range (Ex.100 –110), and then LCD shows to select button range. 100-110 BTN ASSIGN PRESS FLEX_KEY (25-48) ).Dial one digit “1” or “2” for button range. (Ex, dial “2”) 100-110 DIAL 01 – 12 BTN 01 = CO 001 To program Flexible Button, press the Flex. BTN which you want to program (Ex. BTN 1). The LCD will display current BTN assignment of the first station in the range, and LED of the BTN (Ex. BTN 1) will be lit. (See Table 3.6.3). And input one digit to choose type. If needed, enter data, then entered data will be displayed on the LCD. (See Table 3.6.3) SELECT BTN RANGE D1:F01-F24 D2:F25-F48 Press the [HOLD/SAVE] button for updating database permanently. SELECT BTN RANGE D1:F01-F24 D2:F25-F48 Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (2) without updating system memory.

Programming Manual 80 BTN 12-Button (Digital) 24-Button (Digital) 1 {CO 1} {CO 1} 2 {CO 2} {CO 2} 3 {CO 3} {CO 3} 4 {CO 4} {CO 4} 5 {CO 5} {CO 5} 6 {CO 6} {CO 6} 7 {CO 7} {CO 7} 8 {CO 8} {CO 8} 9 {CO 9} {CO 9} 10 {CO 10} {CO 10} 11 {CO 11} {CO 11} 12 {LOOP} {LOOP} 13 - 24 - TABLE 3.6.2 Initial Button Configuration (PGM 115) BTN TYPE DATA Button 01 - 24 1 - 24 01 : User Button 02 : CO 03 : CO GRP 04 : LOOP 05 : STA … 06 : STA PGM (11-99) 07 : SPD (00-99) 08 : SYS SPD 09 : Num Plan Code 10 : Networking DSS Button 11 : MSN Button 12 : Hunt Group Button - CO Line CO Group - Station No. Station Programming Code Speed Bin No. System Speed Bin No. Num Plan Code Networking DSS Number MSN Number Hunt Group Number TABLE 3.6.3 Button Configuration for Flexible Button Assignments (PGM 115)

Programming Manual 81 3.7 STATION COS (PGM 116) All stations‟ COS for day and night operation are 1 as default. For a particular call, the CO COS is combined with station COS to determine restriction. Each station must be assigned a class of service which governs that station's toll restriction for the day and night operation. The weekend COS is same as night COS. (Table 3.7.1 and Table 3.7.2) STA COS 1 No restrictions are placed at the station for dialing. STA COS 2 The assignments in the Exception Table A are monitored for allow and deny numbers. STA COS 3 The assignments in the Exception Table B are monitored for allow and deny numbers. STA COS 4 The assignments in both Exception Tables A & B are monitored for allow and deny numbers. STA COS 5 The leading digit dialed can not be a long distance code. The dialed digits can be longer than 7 digits. There is no restriction for the number in Canned Toll Table. STA COS 6 The leading digits can not be a Long Distance code. Only eight digits maximum can be dialed. There is no restriction for the number in Canned Toll Table. STA COS 7 Intercom and paging calls are allowed. No dialing allowed on CO lines. ICM boxes are assigned with this COS. STA COS 8 The assignments in the Exception Table C are monitored for allow and deny numbers. STA COS 9 The assignments in the Exception Table D are monitored for allow and deny numbers. TABLE 3.7.1 Station Class-Of-Service (PGM 116) CO COS 1 CO COS 2 CO COS 3 CO COS 4 CO COS 5 STA COS 1 No Restriction Applied No Restriction Applied No Restriction Applied Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. No restriction applied STA COS 2 Exception Table A governs the dialing Exception Table A governs the dialing No Restriction Applied Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. No restriction applied STA COS 3 Exception Table B governs the dialing No Restriction Applied Exception Table B governs the dialing Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. No restriction applied STA COS 4 Exception Table A&B governs the dialing Exception Table A governs the dialing Exception Table B governs the dialing Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. No restriction applied STA COS 5 Restricts Long Distance code. Restricts Long Distance code. Restricts Long Distance code. Restricts Long Distance code. Only within 7 digits. No restriction applied STA COS 6 Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. Restricts Long Distance code. Only within 7 digits. Possible to dial the number in Canned Toll Table. No restriction applied

Programming Manual 82 STA COS 7 In-house dialing only In-house dialing only In-house dialing only In-house dialing only In-house dialing only STA COS 8 Exception Table C governs the dialing Exception Table C governs the dialing Exception Table C governs the dialing Restricts Long Distance code. Only within 8 digits. Possible to dial the number in Canned Toll Table. No restriction applied STA COS 9 Exception Table D governs the dialing Exception Table D governs the dialing Exception Table D governs the dialing Restricts Long Distance code. Only within 8 digits. Possible to dial the number in Canned Toll Table. No restriction applied TABLE 3.7.2 Toll Checking Table (PGM 116) PROCEDURE STATION COS ENTER STA RANGE (1) [TRANS/PGM] + 116. 100-110 STATION COS DAY=1 NIGHT=1 (2) Enter station range (Ex. 100-110). (3) To program, use the BTNs as Table 3.7.3. To change the COS for day operation, press Flex. BTN 1 and dial COS (1 digit) and to change the COS for night operation, press Flex. BTN 2 and dial COS (1 digit). Then changed COS will be displayed on the LCD. (Ex. day = 5, night =3) 100-110 STATION COS DAY=5 NIGHT=3 (4) Press the [HOLD/SAVE] button for updating database permanently. STATION COS ENTER STA RANGE  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN DEFAULT RANGE REMARK 1 1 1 – 9 Day Class-Of-Service 2 1 1 – 9 Night / Weekend Class-Of-Service TABLE 3.7.3 Button Configuration for Station COS (PGM 116)

Programming Manual 83 3.8 CO LINE GROUP ACCESS (PGM 117) If you want to change CO line group access of some stations, program this item. Default gives to access CO Line Group 1 for all stations. PROCEDURE CO GROUP ACCESS ENTER STA RANGE (1) [TRANS/PGM] + 117. SELECT CO GROUP RANGE PRESS FLEX_KEY (1-3) (2) Enter station range (Ex 100-110). In case of ARIA-300 press the Flex. BTN 1~3 to program access authority of the CO line Group. (3) LEDs of BTN 01-24 show current CO line group 01-24 access of the first station in the range. To program CO line group 01-24 access authority, press BTN 01-24 for toggle setting at the CO line group 01-24 Access Programming mode. (LED ON: Station can access the CO line group. / LED OFF: Station cannot access the CO line group.) 100-110 CO GRP (01-24) PRESS FLEX_KEY (4) Press the [HOLD/SAVE] button for updating database permanently.  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN DEFAULT RANGE REMARK 1 - 1-24 CO line Group 01-24 (Toggle) 2 - 1-24 CO line Group 25-48 (Toggle) : ARIA-300 / 600 Only 3 - 1-24 CO line Group 49-72 (Toggle) : ARIA-300 / 600 Only TABLE 3.8.1 CO Line Group Access (PGM 117)

Programming Manual 84 3.9 INTERNAL PAGE ZONE (PGM 118) Each station is assigned to internal paging zone. A station can be in any or no zone at all. Internal all call is defined as the sum of all zones. If station is not in any internal zone, it will not receive any internal page announcement. In ARIA-300 (130) system supports 30(10) internal paging zones. Default assigns all stations to Internal Page Zone 1. PROCEDURE INTERNAL PAGE ZONE ENTER STA RANGE (1) [TRANS/PGM] + 118. SELECT PAGE ZONE RANGE F1: 1-24 F2: 25-30 (2) Enter station range (Ex 100-110). In case of ARIA-300 press the Flex. BTN 1~2 to program access authority of the Internal Page Group. Suppose BTN 1 pressed. 100-110 (ZONE 01-24) PRESS FLEX_KEY (01-24) (3) LEDs of BTNs show currently assigned page zones of the first station in range. To assign Internal page zone to the stations, press one of BTNs for toggle setting. Each button means Internal Page Zone 01-24. (LED ON: Stations are in the internal page zones. LED OFF: Stations are not in the internal page zones.) 100-110 (ZONE 01-24) PRESS FLEX_KEY (01-24) (4) Press the [HOLD/SAVE] button for updating database permanently.  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN DEFAULT RANGE REMARK 1 1 1 - 24 (ARIA-300, Aria-600) 1 - 10 (ARIA-130) Internal Page Zone 01 – 24(10) (Toggle) 2 - 1 - 6 Internal Page Zone 25 - 30 (Toggle) : ARIA-300, Aria-600 Only TABLE 3.9.1 Internal Page Zone Access (PGM 118)

Programming Manual 85 3.10 CONFERENCE PAGE ZONE (PGM 119) Each station is assigned to conference paging zone. A station can be in any or no zone at all. Aria-300, Aria-600 and Aria-130 support 5 conference paging zones. Default assigns all stations to None. PROCEDURE CONFERENCE PAGE ZONE ENTER STA RANGE (1) [TRANS/PGM] + 119. 100 - 110 ( ZONE 31 - 35 ) PRESS FLEX_KEY (1 – 5) (2) Enter station range (Ex 100-110). LEDs of BTNs show currently assigned page zones of the first station in range. In ARIA-130, ZONE 11-15 will be displayed instead of ZONE 31-35. (3) To assign Conference Page zone to the stations, press one of BTNs for toggle setting. Each button means Conference Page Zone 1-5. (LED ON: Stations are in the conference page zones. LED OFF: Stations are not in the conference page zones.) CONFERENCE PAGE ZONE ENTER STA RANGE (4) Press the [HOLD/SAVE] button for updating database permanently. CONFERENCE PAGE ZONE ENTER STA RANGE  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. BTN DEFAULT RANGE REMARK - 1-5 Conference Page Zone (Toggle) TABLE 3.10.1 Conference Page Zone Access (PGM 119)

Programming Manual 86 3.11 ICM TENANCY GROUP (PGM 120) A station belongs to only one ICM tenancy group. A station in ICM Tenancy Group (A) can call another station in other ICM Tenancy Group (B) if the station in the ICM Tenancy Group (A) is programmed to be allowed to access ICM Tenancy Group (B). ARIA-300 / 600 system supports 15 ICM Tenancy Groups and Tenancy ATDs. Aria-130 system supports 5 ICM Tenancy Groups and Tenancy ATDs. PROCEDURE ICM TENANCY GROUP ENTER GRP NUMBER(01-15) (1) [TRANS/PGM] + 120. In ARIA-130, the range will be 1-5. ICM TENANCY GRP 01 F1: ATD F2:ACCESS (2) Enter the group number (Ex. 01). (3) To program ICM Tenancy Group, use the buttons as Table 3.11.1. ICM TENANCY GRP 01 ATD : ….  To assign attendant station of the ICM tenancy group, press BTN 1 and enter the station number to be assigned as attendant, then assigned attendant station number will be displayed on the LCD. ICM TENANCY GRP 01 ENTER ACCESS GROUP(1-15)  To assign accessible ICM tenancy groups for the group, press BTN 2. Then the LCD will show the status and LEDs of BTNs show current accessible ICM tenancy groups. In ARIA-130, the range is 1-5. To change ICM tenancy groups access, press the Flex. BTN for toggle setting. (LED ON: stations have the authority to access the ICM tenancy group. LED OFF: stations have not the authority to access the ICM tenancy group.). Pressing the [CONF] button, the system will goes to step (2) without updating database. ICM TENANCY GRP 01 F1: ATD F2:ACCESS (4) Press the [HOLD/SAVE] button for updating database permanently. ICM TENANCY GRP 01 F1: ATD F2:ACCESS  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (2) without updating system memory. BTN DEFAULT RANGE REMARK 1 - STA No. Attendant station of assigned ICM tenancy group 2 GROUP 01 BTN 01-15 (ARIA-300, Aria-600) BTN 1-5 (ARIA-130) ICM tenancy groups allow to access for assigned group TABLE 3.11.1 Button Configuration of ICM Tenancy Group (PGM 120)

Programming Manual 87 3.12 PRESET CALL FORWARD (PGM 121) A station can be programmed so that incoming CO lines can be forwarded to a preset station or station group if the first station(or station group) does not answer after Preset Call Forward timer. No station is assigned as default. PROCEDURE CALL FWD PRESET ENTER STA NUMBER (1) [TRANS/PGM] + 121. (1:STN /2:HUNT GRP) FROM 101 TO .... (2) Enter the station number to which you want to forward (Ex.101). LCD shows current status of the station. Dial 1 if you want to forward the call to station, or dial 2 if want to forward to hunt group. (Ex. dial 2.) ENTER FWD HUNT GRP NO. FROM 101 TO HUNT .... (3) Enter the preset hunt group number which first station forward to. (Ex.620) CALL FWD PRESET FROM 101 TO HUNT 620  To clear the Preset Call Forward station, press the [SPEED] button. CALL FWD PRESET ENTER STA NUMBER (4) Press the [HOLD/SAVE] button for updating database permanently. CALL FWD PRESET ENTER STA NUMBER  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory.

Programming Manual 88 3.13 HOT LINE / WARM LINE (PGM 122) This feature lets a station perform a pre-assigned feature as soon as lifting handset or pressing the [MON] button as if a station selects the feature (Hot Line). On the other hand, Idle Line Selection for a station which is assigned to warm line, is activated when takes no action for Warm Line Timer after lifting handset or pressing the [MON] button (Warm Line). Warm line is programmable at PGM 113. By default, all stations are not assigned any Idle Line Selection. PROCEDURE IDLE LINE SELECTION ENTER STA RANGE (1) [TRANS/PGM] + 122. 100-110 IDLE LINE NOT ASSIGNED (2) Enter station range (Ex.100-110). User can enter one digit (1-4) and LCD shows the default value of idle line selection. (3) To program Idle Line Selection, use the Table 3.13.1. To assign Idle Line Selection, dial one digit (1-4) and enter related data. Then selected value and the related data will be displayed on LCD. Otherwise, to delete any Idle Line Selection, press the [SPEED] button, then Idle Line Selection assignment will be deleted. IDLE LINE SELECTION ENTER STA RANGE (4) Press the [HOLD/SAVE] button for updating database permanently. IDLE LINE SELECTION ENTER STA RANGE  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. DGT ITEM RANGE REMARK 1 Flex. BTN 01 - 44 To activate a feature on a flex button as if pressed. 2 CO Line 01 – 40 (Aria-130) 001 – 200 (Aria-300) 001 – 400(Aria-600) To seize a CO Line 3 CO Group 01 – 72 (Aria-300, Aria-600) 01 – 24 (Aria-130) To seize a CO Line Group 4 Station 100 – 227 (Aria-130) 100 – 399 (Aria-300) 1000 – 1599 (Aria-600) To call an another station TABLE 3.13.1 Button Configuration for Hot Line/Warm Line (PGM 122)

Programming Manual 89 3.14 CTI STATION ATTRIBUTE (PGM 123) This sets the features/modes used when CTIU8/30 or CTI module is connected at a key station. User can use a CTI keyset with PC when the CTI station mode is set to CTI mode. (Please refer to the User‟s Guide of TAPI-NT.) PROCEDURE CTI STATION ATT ENTER STA RANGE (1) [TRANS/PGM] + 123. CTI STATION ATT PRESS FLEX_KEY (1-2) (2) Enter station range (Ex.100 - 110). User can select Flex. BTN 1or 2. 100-110 CTI MODE (0-2) CTI MODE (2) (3) To program, use the Flex BTNs as Table 3.14.1. To program the CTI station's mode, press Flex. Button 1 and dial CTI mode 0-2. By default, CTI station's mode is CTI mode (1). 100-110 STA BAUD(0-2) 1200 (1) (4) To program the CTI station's baud rate, press Flex. Button 2 and dial baud rate 0-2. By default, CTI station's baud rate is 1200 (0). 100-110 STA BAUD(0-2) 1200 (1) (5) Press the [HOLD/SAVE] button for updating database permanently. CTI STATION ATT PRESS FLEX_KEY (1-2)  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (2) without updating system memory. BTN ITEM DEFAULT RANGE REMARK 1 CTI Station Mode 1 0-2 Determines the CTI keyset mode 0: Inactive, 1: CTI Mode, 2: At Mode 2 CTI Station's Baud Rate 0 0-2 Determines the baud rate of the CTI keyset 0: 1200, 1: 2400, 2: 4800 TABLE 3.14.1 Button Configuration for CTI Station Attribute (PGM 123)

Programming Manual 90 3.15 SMDR ACCOUNT GROUP (PGM 124) Stations can be assigned as member of call account group on SMDR. A station belongs to only one call account group. In ARIA-300 (130), system supports 99(23) SMDR Account Groups. All stations are not assigned as member of any Call Account Group by default. PROCEDURE SMDR ACCOUNT GROUP ENTER STA RANGE (1) [TRANS/PGM] + 124. 100-110 SMDR ACCT GRP (00 – 99) : 01 (2) Enter station range (Ex.100-110). LCD shows current account group status of the first station in the range. In ARIA-130, the range is 00-23. (3) To assign Call Account Group: enter group number, then assigned Call Account Group Number will be displayed on the LCD. Otherwise, to cancel assignment of Call Account Group, press the [SPEED] button then it will be displayed on the LCD. SMDR ACCOUNT GROUP ENTER STA RANGE (4) Press the [HOLD/SAVE] button for updating database permanently. SMDR ACCOUNT GROUP ENTER STA RANGE  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. PGM BTN ITEM RANGE DEFAULT REMARK 124 SMDR Account Group Assign 00 – 99(ARIA-300, Aria-600) 00 – 23(ARIA-130) 00 (Not Assigned)

Programming Manual 91 3.16 COPY DSS BUTTON (PGM 125) The assigned DSS button can be copied to another station or ICM group. PROCEDURE COPY DSS BTN FROM STA … (1) [TRANS/PGM] + 125. COPY DSS FROM STA 105 F1: TO STA F2: TO ICM GRP (2) Enter station number (Ex.105), and then LCD shows the dialed station. COPY DSS FROM STA 105 TO STA … (3) Chose the flexible button 1 or 2 according to destination – station or ICM group.(Ex FLEX 1) COPY DSS FROM STA 105 TO STA 110 (4) Enter the station number of destination (Ex. 110) COPY DSS FROM STA 105 F1: TO STA F2: TO ICM GRP Press the [HOLD/SAVE] button for updating database permanently. COPY DSS FROM STA 105 F1: TO STA F2: TO ICM GRP Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory. 3.17 DISPLAY STATION NUMBER BY COS (PGM 130) System can display stations by assigned Day or Night COS. PROCEDURE DISPLAY STA BY COS F1:DAY COS F2:NIGHT COS (1) [TRANS/PGM] + 130. DISPLAY STATIONS ENTER DAY COS NO (1-7) (2) Press the flexible button 1 or 2 (Ex, FLEX 1 for Day COS) 100 101 102 103 104 105 106 … Dial digit “1”, and then LCD shows stations which are assigned COS 1. DISPLAY STA BY COS F1:DAY COS F2:NIGHT COS Press the [CONF], then system goes to step (1).

Programming Manual 92 3.18 DISPLAY STATION NUMBER BY CO ACCESS GROUP (PGM 131) System can display stations by CO access group. PROCEDURE CO GRP ACCESS STATIONS ENTER CO GRP (01-72) (1) [TRANS/PGM] + 131. 100 101 102 103 110 111 … … (2) Dial one digit of COS (Ex, 1), and then LCD shows stations that are assigned to access CO group 1. DISPLAY STA BY COS F1:DAY COS F2:NIGHT COS Press the [CONF], then system goes to step (1).

Programming Manual 93 4 CO LINE PROGRAMMING If CO line features are to be changed, press the [TRANS/PGM] button and dial 140-144 in Admin Programming Mode. When programming, LCD and LEDs indicate current programmed data and programming status. If the programmer enters correct data, then LCD and LEDs show the entered data and the data is stored in the temporary buffer area. To save the data permanently, press the [HOLD/SAVE] button, then all data in the temporary buffer (same as LCD/LEDs show their status) are stored into system memory. 4.1 CO SERVICE TYPE (PGM 140) In this program mode, you can program the following items; PROCEDURE COL SERVICE ATT ENTER COL RANGE (1) [TRANS/PGM] + 140. 001-002 COL SVC F1:TYPE F2:SUB ATT (2) Enter CO line range. User can select COL Service Type by pressing Flex. BTN 1. 001-002 SVC TYPE (1-5) NORMAL CO (1) (3) To program, select the desired type as Table 4.1.2. Press digit 1-5 to select CO service type (Type 1-5 is exclusive and the default value is NORMAL CO.). 001-002 SVC TYPE (1-5) ISDN DID / MSN (3)  To change the type, press another digit (Ex. 3), then LCD displays the select type immediately. To save the current type, press the [HOLD/SAVE] button. 001-002 COL SVC PRESS FLEX_KEY (1-2) (4) To set the sub-attributes of the selected type, press Flex. BTN 2. See Table 4.1.2. 001-002 DISA ATT F1:DAY F2:NIGHT F3: WEND (5) In Normal CO type, user can set the 3 sub-attributes; Day, Night, or Weekend. Each attribute also has 3 sub attributes. At first, choose a Flex. BTN. (Day/Night/Weekend: 1, 2, 3) See Table 4.1.2. 001-002 DISA ATT F1: SVC F2: VMIB (6) User can set the DISA attributes by pressing Flex. BTN 1~2. Do this procedure for other attribute. See Table 4.1.2. 001-002 DISA SVC (1 : ON/ 0 : OFF) : OFF  Press Flex. BTN 1 to set DISA Service ON/OFF. After entering the desired value, press the [HOLD/SAVE] button to save the value. 001-002 VMIB ANNC VMIB MSG .. (00-70)  Press Flex. BTN 2 to select VMIB Announcement No.  When VMIB Announcement number is assigned and CCR table (PGM 228) matched with VMIB Announcement No is programmed, CCR feature is activated. COL SERVICE ATT ENTER COL RANGE (4) Press the [HOLD/SAVE] button for updating database permanently. COL SERVICE ATT ENTER COL RANGE  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory.

Programming Manual 94 ITEM REMARK Normal CO All lines are assigned as normal CO lines as default. Each CO line in the system can be programmed as DISA (Direct Inward System Access) line and the DISA types are as follows; - Flex BTN 1 (Day) / 2 (Night) / 3 (Weekend) - Each DISA type (BTN 1-3) has sub-attribute F1: DISA Service On/Off F2: VMIB Message No. (Voice announcement (VMIB Message) can be assigned (00-70 and it is not assigned (00) as default.) Analog DID Each CO line in the system can be programmed as DID (Direct Inward Dialing) line and the DID types are as follows; - 1(Immediate Start) / 2 (Wink Start) / 3 (Delayed Dial Start) (BTN 1-3 are exclusive) ISDN DID/ MSN If ISDN board (BRIB, PRIB) is assigned for operating with DID type. TIE TIE line types are as follows; - / 1 (RD) / 2 (LD) / 3 (EM-C) / 4 (EM-D) / 5 (EM-I) DCO DID If R2DCOB (E1 R2) board is assigned for operating with DID type. TABLE 4.1.1 CO Service Type (PGM 140) BTN TYPE FLEX BTN 2 DEFAULT SUB ATTR REMARK 1 Normal CO DISA Attributes -Flex BTN 1 (Day) -Flex BTN 2 (Night) -Flex BTN 3 (Weekend) For each Item; Flex BTN 1 - DISA Service: ON/OFF Flex BTN 2 – VMIB MSG (00- 70) (00: not assigned) 2 ANALOG DID Flex BTN 1 : (Signal Type) Flex BTN 2 : (INFO NO) - Signal Type –1: Immediate Start 2: Wink Start 3: Delayed Dial Start INFO NO : 00 – 70 (00: not assigned) N/A Australia 3 ISDN DID / MSN 4 TIE 1:RD 2:LD 3:EM-C 4:EM-D 5:EM-I RD - 1:RD: Korea 2:LD: India Enter digit 5 DCO DID N/A Australia TABLE 4.1.2 Button Configuration for CO Service Type (PGM 140)

Programming Manual 95 If CO Service type is Normal PGM BTN ITEM RANGE DEFAULT REMARK 140 1 CO Service Type 1-5 1 (Normal) 2 Detailed Attribute BTN DISA 1 Day DISA SVC ON /OFF OFF VMIB ANNC 00-70 00(NOT_ASG) 2 Night DISA SVC ON /OFF OFF VMIB ANNC 00-70 00(NOT_ASG) 3 W/end DISA SVC ON /OFF OFF VMIB ANNC 00-70 00(NOT_ASG) TABLE 4.1.3 Button Configuration for CO Service Type (PGM 140) If CO Service type is ISDN DID/MSN, PGM BTN ITEM RANGE VALUE REMARK 140 1 CO Service Type 1-5 3 ISDN DID/MSN 2 Detailed Attribute No Attributes Required TABLE 4.1.4 Button Configuration for CO Service Type (PGM 140) If CO Service type is TIE, PGM BTN ITEM RANGE VALUE REMARK 140 1 CO Service Type 1-5 TIE (4): 2 Detailed Attribute TIE Attribute TIE SIG 1-5 Not Assigned 1: RD 2: LD 3: EM-C 4: EM-D 5: EM-I TABLE 4.1.5 Button Configuration for CO Service Type (PGM 140)

Programming Manual 96 4.2 CO LINE ATTRIBUTE – I (PGM 141) PROCEDURE CO LINE ATT 1 ENTER COL RANGE (1) [TRANS/PGM] + 141. 001-002 CO LINE ATT1 PRESS FLEX_KEY (1-10) (2) Enter CO line range. (3) To program, press the Flex. BTN as Table 4.2.1. Press BTN 1- 10 and enter related data, then entered data will be displayed on the LCD. 001-002 DISA ACCT CODE (1 : ON/ 0 : OFF) : OFF (4) Press Flex. BTN 3 and assign DISA Account Code. 001-002 FLASH TYPE (1: GND/ 0: LOOP) : LOOP (5) To set Flash Type, press Flex. BTN 7. 001-002 FLASH TYPE (1: GND/ 0: LOOP) : LOOP (6) To alter Flash Type, dial 1-0 .(Ex. dial 1) 001-002 DISA ACCT CODE (1 : ON/ 0 : OFF) : OFF (7) Press the [HOLD/SAVE] button for updating database permanently. CO LINE ATT 1 ENTER COL RANGE  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory.

Programming Manual 97 BTN ITEM RANGE DEFAULT REMARK 1 CO Line Group 00-73 (Aria-300, Aria-600) 00-25 (Aria-130) 01 Groups should be assigned according to CO type and Class-Of-Service. (00:private, 73(25) : not used) 2 CO COS 1-5 1 -CO COS 1: no restriction -CO COS 2: Exception Table A governs -CO COS 3: Exception Table B governs -CO COS 4: restricts Long Distance Code -CO COS 5: overrides STA. COS 2,3,4 and 5, 6. 3 DISA Account Code ON/OFF OFF When accessed another CO line in the system by DISA line, you should enter authorization code if this flag is set. 4 CO Line Assign POL/LOOP LOOP Polarity Reverse, Loop Start 5 CO Line Type PBX/CO CO When marked PBX, a 1 or 2 digit dial code may be entered after which toll restriction is applied. 6 CO Line Signal Type DTMF/PULSE DTMF DTMF, Pulse 7 Flash Type GROUND/LOOP LOOP 8 UNA ON/OFF OFF The allowance of Universal Night Answer service 9 CO Line Group Account ON/OFF OFF 10 CO Tenancy Group 01-15(Aria-130, Aria-600) 01-10(Aria-130) 01 Tenancy Group of CO line. TABLE 4.2.1 Button Configuration for CO Attribute - I (PGM 141)

Programming Manual 98 4.3 CO LINE ATTRIBUTE – II (PGM 142) PROCEDURE CO LINE ATT 2 ENTER COL RANGE (1) [TRANS/PGM] + 142. CO LINE ATT 2 PRESS FLEX_KEY (01-15) (2) Enter CO line range. (3) To program, use the Flex. BTNs as Table 4.3.1. Flex. BTN 1, 4, 7-11,15 may set On/Off. Press BTN 2, 3, 5, 6, 12, 13 and enter related data for setting, then entered data will be displayed on the LCD. 001-002 CO DIST RING (0-4) : 3 (4) To assign CO Distinct Ring, press Flex. BTN 5. (Ex. To change Ring Type, dial 0-4. (Ex: dial 3)) 001-002 CO DIST RING (0-4) : 3 (5) Press the [HOLD/SAVE] button for updating database permanently. 001-002 MOH(00-15) INT MUSIC (1) (6) To change MOH type, press Flex. BTN 6, and dial 00-13. In ARIA-130, the range is 00-12 001-002 MOH(00-15) INT MUSIC (1) (7) Press the [HOLD/SAVE] button for updating database permanently. CO LINE ATT 2 PRESS FLEX_KEY (01-15)  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (2) without updating system memory. BTN ITEM RANGE DEFAULT REMARK 1 CO Line Name Display ON/OFF OFF If CO line name is assigned at BTN2, and this field is ON, CO name is displayed when a CO line call is received. 2 CO Line Name Assign Max 12 char - Max 12 characters 3 Metering Unit 00-06 00 There are 7 metering signal types: - 0 : None - 1 : 50 Hz - 2 : 12 KHz - 3 : 16 KHz - 4 : Singular Polarity Reverse (SPR) - 5 : Plural Polarity Reverse (PPR) - 6 : No Polarity Reverse (NPR) 4 Line Drop using CPT ON/OFF OFF If this field set to ON, CPT checks the incoming CO line when answered and if CPT detects dial tone, then system drops the line for toll restriction.

Programming Manual 99 BTN ITEM RANGE DEFAULT REMARK 5 CO Distinct Ring 0-4 0 The CO line can give his own ring type signal to station in system through this field. This ring type can be programmed at PGM 422. 6 CO Line MOH 00-13 (Aria-300, Aria-600) 00-12 (Aria-130) 1 00: Not assigned by this field. 01: Internal Music 02~04: External Music (04=MPB, Aria-600=LMUE) 05~06(07): VMIB MOH 07(08)-11(12): SLT MOH 12(13): Hold Tone 7 PABX CO Dial Tone YES/NO YES YES: PX or PABX provides dial tone. NO: PX or PABX does not provide dial tone and the ARIA system provides dial tone. 8 PABX CO Ring Back Tone YES/NO NO If R2 PX which does not give you tone for called party status exists, then the system provides tone according to cause value (This field is only when Cause means that Ring back is provided by PX.). YES: PX, NO: System 9 PABX CO Error Tone YES/NO NO If R2 PX which does not give you tone for called party status exists, then the system provides tone according to cause value (This field is only when Cause means that error tone is provided by PX.). YES: PX, NO: System 10 PABX CO Busy Tone YES/NO NO If R2 PX which does not give you tone for called party status exists, then the system provides tone according to cause value (This field is only when Cause means that busy tone is provided by PX.). YES: PX, NO: System 11 PABX CO Announce Tone YES/NO NO If R2 PX which does not give you tone for called party status exists, then the system provides tone according to cause value (This field is only when Cause means that announcement is provided by PX, but the system provides only error tone.). YES: PX, NO: System 12 CO Flash Timer 000 – 300 005 10msec base 13 Open Loop Detect Timer 00 - 20 00 100msec base 14 Line Length N / A For Australia (South Africa only) 15 DISA Ans Timer 1-9 5 TABLE 4.3.1 Button Configuration for CO Attribute - II (PGM 142)

Programming Manual 100 4.4 ISDN CO LINE ATTRIBUTE I (PGM 143) PROCEDURE COL ISDN ATT ENTER CO RANGE (1) [TRANS/PGM] + 143. 001-009 COL ISDN ATT PRESS FLEX KEY (01-11) (2) Enter CO line range. (3) To program, press the Flex. BTN as Table 4.4.1. BTN 6 can toggle for the value. Press other BTNs and enter related data for setting, then it will be displayed entered data on the LCD. 001-009 DID REMOVE NO (00-99) : 00 (4) To set DID Remove Number, press Flex. BTN 5. (Ex. To alter DID_RN dial number, dial 21.) 001-009 DID REMOVE NO (00-99) : 21 (5) Press the [HOLD/SAVE] button for updating database permanently. 001-009 COL ISDN ATT PRESS FLEX KEY(01-11)  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (2) without updating system memory.