AER Compact Slope Operation & User’s Manual

4 3. Controls and connections 5 3.1 Front side 5 3.2 Rear side 6 4. Starting up 7 4.1 Cabling and switching-on 7 4.2 Level adjustment 7 5. Functional characteristics 7 5.1 Equalization 7 5.2 Effects 8 5.3 Footswitch 8 5.4 Phantom powering 8 6. Technical specifications 9 7. Circuit diagram 10

Thank you for choosing the Compact Slope. The Compact Slope is a professional, compact and powerful amplifier system. Especially developed for the enhancement of acoustic instruments it is nonetheless suitable for other instruments, even electrical ones. Our design concept was focused on the singer-/ songwriter who requires outstanding reproduction of his instrument and vocals and prefers the sound source on the floor addressing him in an angle. (45°) The Compact Slope accomplishes this by combining well approved Compact 603 with a wedge design cabinet. All AER-systems are subtly dynamically controlled, which ensures absolute reliability in full load opera- tion despite strikingly small sizes and little weight. Read on and have fun using your Compact Slope!

The following guidelines shall help minimize the risk of injury through fire or electric shock. 1. Carefully read these safety notes before you use the device! 2. Keep these safety notes in a safe place. 3. Pay attention to all warnings, instructions and additional texts on the unit. 4. This device was only designed for operation under normal climatic conditions (temperate climate). 5. Do not install or use your amp in close proximi- ty to water or if you are wet yourself. 6. Do not subject your device to sudden and severe temperature changes. This could cause moisture condensation inside the unit, which could damage it. In the event of moisture condensation allow the device to dry out com- pletely before use. 7. Use your amp in a safe place where nobody can step on cables or trip over and damage them. 8. Pay attention to an unhindered air circulation around the amp, never obstruct the air vents or grilles. 9. Always pull the mains plug before cleaning your amp or when left unused for a long period of time. Use only a dry cloth for cleaning. Avoid the use of detergents and do not let any liquids seep into the unit. 10. Use only the right fuses with the same current rating and trigger characteristic as replace- ments. Never mend fuses! Pull the mains plug before replacing a fuse. Should a fuse blow again after a short while, the device needs to be checked. 11. Never install your amp close to devices with strong electromagnetic fields such as large mains transformers, revolving machines, neon illumination etc. Do not lay signal cables paral- lel to power current cables. 12. There are no user-serviceable components inside the unit. To avoid the risk of an electric shock, the unit must not be opened. All main- tenance, adjustment and repair works should be carried out by qualified staff only. Any unauthorized tampering will void the 2-year warranty. 13. In keeping with the EMV regulations screened cables with correctly fitted connectors must be used for all signal connections. 14. Always use an earthed power supply with the correct mains voltage. If you are in doubt about the power outlet ground, have it checked by a qualified technician. 15. Cable up your amp only when it is powered off. 16. This device should be installed near the socket outlet and disconnection of the device should be easily accessible. The mains plug of the powersupply shall remain readily operable. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus. 17. This product may cause permanent hearing loss. Do not operate for long periods of time at a high volume level or at any level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. 18. The product should be located away from heat sources such as radiators, heat registers or other products that produce heat. 19. Do not place any open sources of fire, like candles, on the device. 20. Care should be taken so that objects do not fall onto the device and liquids are not spilled into the enclosure through openings. Ensure that no objects filled with liquids, such as vases, are placed on the device. 21. Do not place this device on an unstable cart, stand, tripod, bracket or table. The device may fall, causing serious injury to you and serious damage to the device itself. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AT TENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR The lightning flash with the arrow head symbol within an equilateral triangle is intended to alert the user to the presence of unisolated ´dangerous voltage´ within this product´s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this product.

efx mains & master 3.1 Front side 1) input (ch. 1) signal input, socket for 6,3 mm mono jackplug 2) high/low input sensitivity switch, attenuator = off = on 3) clip overload indicator 4) gain input level control 5) colour tone colour fi lter activation switch = not active = active 6) bass bass frequency level control 7) middle middle frequency level control 8) treble treble frequency level control 9) input (ch. 2) signal input, combo-socket for 6,3 mm mono jackplug and XLR-connectors 10) line/mic signal source selector switch: line (only via jackplug) for instruments (pickup) and other line level sources, mic (only via XLR-connector) for microphones 11) pan eff ect signal distribution control 12) select eff ect select switch 13) level level control internal eff ect 14) power on/off status indicator 15) master master level control 3. Controls and connections IF_Compact603_20120529 Compact 603 1 2 3 3 4 4 5 6 6 7 8 8 9 10 11 12 13 14 15

DO NOT OPEN AT TENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Made in Germany by B Compact 603 twin channel acoustic amplifier tip = int. efx ring = ext. efx on/off 1 = gnd 2 = pos 3 = neg DI-out footswitch IB_Compact603_20120529 1 2 3 4 5 7 8 6 3.2 Rear side 1) line out The line out supplies a pre-amp signal taken after tone-control, eff ects and master for forwarding to other appliances. 2) headphones This output enables you to connect stereo head- phones and mutes the loudspeaker. !!!Warning: Only use headphones with stereo jackplugs in this output socket!!! 3) send Send is an output to connect to an external eff ect device and in conjunction with return (input) forms a loop here designed as external eff ect loop. The eff ect can be switched on or off via footswitch. 4) return Return as part of the eff ect loop operates as signal input from an external eff ect device (from output of the eff ect device). The eff ect can be switched on or off via footswitch. Return on its own can also be used as quasi auxiliary signal input (-10 dbV). 5) tuner The tuner output supplies a pre-master signal (-9 dbV) to connect an external tuner to the Compact Slope. 6) footswitch Connection socket for a double-footswitch (on-/ off -switch, tip = internal eff ect/ring = external eff ect on/off ). 7) DI-out Preamp-output with symmetrical signal, after tone- control, pre master, without eff ects. 8) power on Combined mains switch with mains socket and fuse holder.

4.1 Cabling and switching on Before connecting to mains, please ensure that your local mains voltage is suitable for the voltage of the device (e.g. 120V in the USA, 230V in Europe). The relevant specs and safety sym- bols are printed on the rear side of the unit. Connect all cables according to your application and switch the amplifi er on. The green power con- trol LED indicates operational readiness. 4.2 Level adjustment First ensure, that the master level control is zeroed (over to far left), so that when you are setting the sound level, the signal passes through the elect- ronics only and does not reach the loudspeaker. By pressing the high-/low- (attn.) resp. line-/mic- switches you can adapt the amplifi er to your signal sources (guitar pickups, microphone etc). Turn the gain control clockwise until the red clip indicator fl ashes momentarily when playing with a strong attack. Thus you make sure that your signal source (e.g. instrument) provides the input-stage of the amplifi er with the necessary input. colour bass middle treble colour bass middle treble Note: Level adjustment By setting the level correctly we mean the signal level in one or several devices in a signal chain is nei-ther too high nor too low. This applies equally to all circuits in a complete circuit design (EQs, preamps etc.) Consequently, care must be taken that no part of the circuit is overloaded or that distortion is unin- tentionally added to the signal. We have carefully designed the circuit to achieve this objective whilst also providing controls for „manual“ intervention. channel 1 IF_Compact603_20120529 Compac channel 2 Compact 603 The clip-LED indicates an overload. A short fl icker is of no danger to AER devices. During operation a short fl icker can be accepted, to be on the safe side you should reduce the gain slightly to achieve an optimal and distortion-free performance. Finally set the desired overall volume level with the master level control. 5. Functional characteristics 5.1 Equalization The triple-/dual-band equalizer of your Compact Slope provides you with an active and high quality sound interaction tool that supports the natural tone of instruments and voice whilst simultane- ously off ering you the possibility of a controlled accentuation. With all controls in mid position the fi lters are set to produce a very pleasing and natural sound impres- sion that you can „colour up“ by using the colour fi lter with the eff ect of lowering the mids and lifting the trebles. The tone becomes more open and light and is especially suited for fi ngerpicking techniques. The equalization can support or soften the eff ect of the colour fi lter and allows a diff erentiated mids- accentuation. A: with colour-fi lter (switch pressed) reduce treble to soften possible sharpness B: without colour-fi lter (switch not pressed) boost treble to brighten the sound Note: The active equalization of the Compact Slope eff ects the signal adjustment. If you spot an intensifi ed fl ickering of the clip indicator, level the signal level with the gain control (s. 4.2 Level adjustment).

can be plugged into the footswitch-socket on the rear side of the amplifier via stereo cable. By this footswitch the internal and external effects can be switched on and off. We wish you lots of fun playing your Compact Slope! P.S.: For questions or suggestions contact us: [email protected] 5.4 Phantom power Microphones requiring 48V phantom power can be connected to the XLR-socket of channel 2 directly. Factory-provided phantom power is activated but, if required, may be deactivated by an internal jumper. In contrary 9V phantom power, if required, can additionally be activated in channel 1 by an internal jumper. Please note: For both alterations the device must be opened, therefore only qualified service per- sonnel may carry out the modifications concer- ning the de-/activating of phantom power. General Note: Use of 48V or 24V phantom power (Phantom power = remote supply, here: powering an audio device via the connected audio line) Turn on the phantom power only if the unit connec- ted to an XLR socket is designed to handle it! In general, suitable units are e.g. condenser microphones, active DI-boxes and other special audio devices, whose power supply is drawn from the phantom power. Such devices are also labelled accordingly; please heed the permissible power consumption (max.10mA). High-quality dynamic microphones with a balanced signal need no phantom power, but can handle it anyway. Other devices, which have not been designed explicitly for phantom power operation, can suffer from considerable malfunctions and damage may result as well. Examples of devices that may be damaged by incorrect application of phantom power include: Low-cost dynamic microphones with a mono jack- plug (unbalanced signal) that were fitted afterwards with an XLR connector. Audio devices with a balanced XLR output (e.g. DI-boxes, effects devices, instrument preamps with a DI output etc.) which are not protected against phantom power applied to their XLR output. (The DI connectors on AER products are protected against applied phantom power.) Other audio devices (such as preamps, effects pedals etc.) whose unbalanced line output was replaced by an XLR socket. If in doubt please consult the manufacturer of the device you are using. 5.2 Effects The Compact Slope has a built-in (internal) digital effect processor, with the select-switch you can choose between 4 different effects: 1 = reverb 1 (short) 2 = reverb 2 (long) 3 = delay (320 ms) 4 = chorus The efx-level-control determines the intensity of the internal effects (left stop = no effect). Furthermore an additional effects unit (external ef- fect) may be connected to the Compact Slope. For this purpose use the send and return sockets on the rear side of the amplifier (send goes to input, return to the output of the external effects device). The intensity of the effect is adjusted at the external effects unit. With the efx-pan control the different effects are blended with the original signal. The efx-pan works as follows: left stop: internal effect on channel 1 external effect on channel 2 mid position: internal effects on channels 1 + 2 external effects on channels 1 + 2 right stop: internal effects on channel 2 external effects on channel 1

TD20150224 Technical data Technical data Technical data Technical data Inputs Inputs Inputs Inputs (notes 1, 2, 4) channel 1 channel 1 channel 1 channel 1 High impedance, unbalanced input for instruments (pick-ups) and line-level sources Mono jack socket, ¼” (6.35 mm) Sensitivity: 22 mV (–33 dBV) High/low (attenuator) switch: –10 dB Impedance: 2.2 Meg Equivalent input noise, A-weighted: 1 uV (–120 dBV) Phantom power (optional): 9 V DC / max. 100 mA, short-circuit protected Switchable instrument or microphone input Combo socket, XLR + jack ¼” (6.35 mm) line mode line mode line mode line mode High impedance, unbalanced input for instruments (pick-ups) and line-level sources Jack socket only Sensitivity: 27 mV (–31 dBV) Impedance: 1 Meg Equivalent input noise, A-weighted: 2.4 uV (–112 dBV) channel 2 channel 2 channel 2 channel 2 mic mode mic mode mic mode mic mode XLR (balanced), stereo jack (balanced), or mono jack (unbalanced) input Sensitivity: 3.3 mV (–50 dBV) Impedance (balanced mode): 1.2 k Impedance (unbalanced mode): 2.7 k Voice filter: –10 dB at 270 Hz (referred to 10 kHz) Equivalent input noise, A-weighted: 0.8 uV (–122 dBV) Phantom power (XLR only): 48 V, max. 10 mA, short-circuit protected clip clip clip clip indicators for ch. 1 and 2 Headroom: min. 8 dB return return return return Input from external parallel effect loop, or supplementary input, before master volume Mono jack, ¼” (6.35 mm) Sensitivity: 320 mV (–10 dBV) Impedance: 20 k (note: impedance changes to 5 k while external effect is switched OFF by footswitch) Outputs Outputs Outputs Outputs (note 3) phones phones phones phones Headphones output. When plugged in, internal speaker is muted. Stereo jack socket, L/R connected, ¼” (6.35 mm) Max. output power: 2 x 100 mW / 1000 ohm Input sensitivity for 2 x 50 mW / 1000 ohm: 23 mV (–33 dBV) at channel 1 input Impedance: 470 ohm (common for L and R) Note: Note: Note: Note: Suitable for headphones with stereo jack. Does not work with mono jacks. tuner tuner tuner tuner Tuner output Mono jack socket ¼” (6.35 mm) Output voltage: 340 mV (–9 dBV) line out line out line out line out Preamplifier output after tone controls, with effects, and after master volume Mono jack, ¼” (6.35 mm) Output voltage: 1.4 V (+3 dBV) DI DI DI DI----out out out out Balanced XLR output before master, after tone controls, without effects 1 = ground 2 = positive 3 = negative Differential output voltage: 140 mV (–17 dBV) send send send send Output to external parallel effect loop Before master, after tone controls Mono jack, ¼” (6.35 mm) Output voltage: 1.4 V (+3 dBV) Footswitch connector Footswitch connector Footswitch connector Footswitch connector footswitch footswitch footswitch footswitch Stereo jack socket ¼” (6.35 mm) for a dual footswitch Tip = internal effect on/off Ring = external effect on/off Sleeve = common (ground) Effect is OFF when the footswitch is ON. Tone controls Tone controls Tone controls Tone controls ch. 1 ch. 1 ch. 1 ch. 1 colour colour colour colour –3 dB at 700 Hz, +10 dB at 8 kHz bass bass bass bass ±8 dB at 100 Hz (shelf type) middle middle middle middle ±6 dB at 800 Hz treble treble treble treble ±8 dB at 10 kHz (shelf type) ch. 2 ch. 2 ch. 2 ch. 2 bass bass bass bass ±8 dB at 100 Hz (shelf type) treble treble treble treble ±11 dB at 10 kHz (shelf type) Effects Effects Effects Effects Internal effects Internal effects Internal effects Internal effects 1 Reverb 1 2 Reverb 2 3 Delay 4 Chorus External effect External effect External effect External effect Parallel effect loop (see also send send send send and return return return return). eff. eff. eff. eff. pan pan pan pan Blends both internal and external effects between channels 1 and 2, with reverse direction of rotation for the external effects. Power Power Power Power Power amp Power amp Power amp Power amp 60 W / 4 ohm, DMOS, monolithic I.C. Dynamic range, A-weighted: 92 dB (note 2) Limiter Limiter Limiter Limiter threshold threshold threshold threshold 50 W Analog signal Analog signal Analog signal Analog signal processing processing processing processing Dedicated equalizer, subsonic filter, adaptive peak limiter Speaker system Speaker system Speaker system Speaker system 8” (200 mm) twin cone full-range speaker, bass reflex enclosure Mains power Mains power Mains power Mains power Mains voltage (depending on model): 100, 120, 230, or 240 V AC, 50–60 Hz Power consumption: max. 120 W Mains fuse Mains fuse Mains fuse Mains fuse 5 x 20 mm T 1 A L / 250 V for 230 and 240 V models T 2 A L / 250 V for 100 and 120 V models General General General General Cabinet Cabinet Cabinet Cabinet 12 mm (0.47”) birch plywood Finish Finish Finish Finish Waterbased acrylic, black spatter finish (standard model) Dimensions Dimensions Dimensions Dimensions 259 mm (10.19“) high 331 mm (13.03“) wide 137 / 326 mm (5.39“ / 12.84”) deep Weight Weight Weight Weight 7.2 kg (15.87 lbs) Notes: Notes: Notes: Notes: 1. Sensitivity 1. Sensitivity 1. Sensitivity 1. Sensitivity Input sensitivities refer to 50 W into 4 ohm, full gain and master settings, neutral tone control settings, and 1 kHz sine-wave test signal. 2. Noise and dynamic range 2. Noise and dynamic range 2. Noise and dynamic range 2. Noise and dynamic range Equivalent input noise voltages are typical values obtained by measuring noise voltage at speaker output and dividing by the voltage gain of the amplifier for white noise. Full gain and master settings, neutral tone control settings, input shorted, measuring bandwidth 20 Hz – 20 kHz. Dynamic range of power amplifier: Ratio of between output signal at limiter threshold to A-weighted output noise with master master master master in zero position. 3. Output levels 3. Output levels 3. Output levels 3. Output levels Output levels refer to 50 mV / 1 kHz sine-wave test signal at channel 1 input, full gain and master settings, neutral tone control settings, send fully clockwise. 4. Options 4. Options 4. Options 4. Options Gain of channel 2 in mic mode can be decreased by 4.6 dB by an internal jumper. 48 V phantom power can be deactivated by an internal jumper. 9 V phantom power for channel 1 can be applied by an internal jumper to the “ring” terminal of the input jack. Caution: Caution: Caution: Caution: Use this option with care. Read the operating instructions. Specifications and appearance subject to change without notice.

B090216C_20110401 LINE MIC MIC LINE +9V GAIN COLOUR MIDDLE OFF/ON SUBSONIC LIMITER POWER AMP FX DUAL CONE SPEAKER TUNER TREBLE BASS BASS TREBLE CLIP Clip detect CLIP Clip detect SEND EFF. RETURN MASTER LINE OUT F/S RETURN PHONES 470R DI GAIN +48V PREAMP VOICE 6k8 6k8 EFFECT PAN PREAMP MIC GAIN H/L SELECT 9V Phantom Power 48V Phantom Power PAD CH 1 CH 2 T R T R T R 1 2 3 1 2 3 T R