Aaeon ACP-5185 Manual 

A C P - 5 1 8 5 ACP-5185 18.5” Intel® CoreTM i7/i5 Processor High Brightness Fanless Multi-Touch Panel PC ACP-5185 Manual 4th Ed January 2013

A C P - 5 1 8 5 i Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, nor for any infringements upon the rights of third parties, which may result from its use. The material in this document is for product information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, AAEON, assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users.

A C P - 5 1 8 5 ii Acknowledgments  Intel®, CoreTM are registered trademarks of Intel® Corporation.  Microsoft® Windows is a registered trademark of Microsoft® Corporation.  RTL is a trademark of Realtek Semi-Conductor Co., Ltd.  C&T is a trademark of Chips and Technologies, Inc.  UMC is a trademark of United Microelectronics Corporation.  ITE is a trademark of Integrated Technology Express, Inc. All other product names or trademarks are properties of their respective owners.

A C P - 5 1 8 5 iii Packing List Before you begin installing your Panel PC, please make sure that the following items have been shipped:  ACP-5185 Infotainment Multi-Touch Panel PC  HDD screws  Product DVD Contains User’s Manual (in PDF format), Drivers and Utilities If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.

A C P - 5 1 8 5 iv Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage. 7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS. 8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient over-voltage. 12. Never pour any liquid into an opening. This could cause fire or electrical shock. 13. Never open the equipment. For safety reasons, only qualified service personnel should open the equipment.

A C P - 5 1 8 5 v 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT. 16. External equipment intended for connection to signal input/output or other connectors, shall comply with relevant UL / IEC standard (e.g. UL 1950 for IT equipment and UL 60601-1 / IEC 60601 series for systems – shall comply with the standard IEC 60601-1-1, Safety requirements for medical electrical systems. Equipment not complying with UL 60601-1 shall be kept outside the patient environment, as defined in the standard. 17. When the temperature of CPU is higher than 35°C, the frequency of CPU will be adjusted automatically. For example, if the temperature of Intel Core i7 is 40°C, the frequency of the CPU will be between 1.8~1.3 GHz. Caution: It may cause the danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer.

A C P - 5 1 8 5 vi Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IPX0 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5. Type of protection against electric shock: Class I equipment

A C P - 5 1 8 5 vii FCC This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.

A C P - 5 1 8 5 viii UL Module Description ACP-5185 AC modules are developed to suitable for the Classification Mark requirement

A C P - 5 1 8 5 ix Safety Symbol Description The following safety symbols are further explanations for your reference. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1 Attention, consult ACCOMPANYING DOCUMENTS. Ground wire Protective Ground wire. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1

A C P - 5 1 8 5 x Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 中央处理器 与内存 × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述部件物质中央处理器、内存、硬盘、光驱、触控模块为选购品。

A C P - 5 1 8 5 xi Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification.............................................................. 1-4 1.4 General Information................................................... 1-7 Chapter 2 Hardware Installation 2.1 Safety Precautions .................................................... 2-2 2.2 A Quick Tour of the ACP-5185.................................. 2-3 2.3 2.5” Hard Disk Drive (HDD) Installation .................... 2-6 Chapter 3 AMI BIOS Setup 3.1 System Test and Initialization . ................................. 3-2 3.2 AMI BIOS Setup........................................................ 3-3 Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming the Watchdog Timer A.1 Programming .........................................................A-2 A.2 ITE8781 Watchdog Timer Initial Program..............A-6 Appendix B I/O Information B.1 I/O Address Map....................................................B-2 B.2 1st MB Memory Address Map ................................B-4

A C P - 5 1 8 5 xii B.3 IRQ Mapping Chart ..............................................B-5 B.4 DMA Channel Assignments...................................B-5 Appendix C Miscellanea C.1 General Cleaning Tips.......................................... C-2 C.2 Cleaning Tools...................................................... C-3 C.3 Scrap Computer Recycling ................................. C-5 C.4 Installing Accessories ........................................... C-6

A C P - 5 1 8 5 Chapter 1 General Information 1-1 General Chapter 1 Information

A C P - 5 1 8 5 Chapter 1 General Information 1-2 1.1 Introduction The ACP-5185 is a Multi-Touch Infotainment Panel PC with superior onboard Intel® Core™ i7/i5 processor-based computer. It is a PC-based system with 18.5” true color TFT LCD display, integrated multimedia functions make them the perfect platforms to build comprehensive lifestyle computing applications. The ACP-5185 includes all the features of a powerful computer into a slim and attractive chassis. The ACP-5185 has 300 nits TFT display with 1366 x 768 resolution. This model equips two-point Multi-Touch Window design and is easy to clean. Moreover, it is IPX1 100% water-proof that can be installed in harsh environments. Its front bezel is IP-65/NEMA4 for auxiliary water-proof protection. In addition, the ACP-5185 deploys 7H hardness Anti-Scratch Surface to avoid accidental damage. The ACP-5185 supports one 2.5” SATA Hard Disk Drive and one CompactFlash™ slot for the storage functions, and one Mini-Card expansion. Moreover, it supports Smart Card Reader, RFID, MSR, Bluetooth, Skype phone, and camera to fulfill the demands of versatile applications.

A C P - 5 1 8 5 Chapter 1 General Information 1-3 1.2 Features  18.5” WXGA (1366 x 768) Fanless TFT LCD Display  Easy-To-Clean: Multi-Touch Window Design (Two-Point)  Superior Intel® Core™ i7/i5 Processor  IPx1 100% Water-Proof  Anti-Scratch Surface (7H Hardness)  Smart Card Reader/ RFID/ MSR/ Bluetooth/ Skype Phone/ Camera Support (Optional)

A C P - 5 1 8 5 Chapter 1 General Information 1-4 1.3 Specification System  Processor Onboard Intel® Core̬ i7/i5 Processor  System Memory DDR3 SODIMM x 1, Max. 4 GB  LCD / CRT Controller Integrated graphics in Intel® QM57  I/O Port USB2.0 x 6 (2 on side; 4 on rear) RS-232 x 1 Line-out x 1 VGA x 1  Storage Disk Drive 2.5” SATA Hard Disk Drive x 1; CompactFlash™ slot x 1 (Internal)  Expansion Mini Card x 1  OS Support Windows® XP (T/S: Single point), Linux (T/S: Single point), Windows®7 (T/S: Multi-point) Mechanical  Construction IP-65/ NEMA4 for front bezel, IPX1 for chassis  Mounting VESA 100  Dimension 18.11”(W) x 12.2”(H) x 3.39”(D) (460mm x 310mm x 86mm)  Carton Dimension 26” x 8.11” x 19.53’’ (661mm x 206mm x 496mm)

A C P - 5 1 8 5 Chapter 1 General Information 1-5  Net Weight 15.4 lb (7 kg)  Gross Weight 19.8 lb (9 kg) Environmental  Operating Temperature 32oF~104oF (0oC~40oC) (Ambient With Airflow)  Storage Temperature -4oF~140oF (-20oC~60oC)  Storage Humidity 10%~95% @ 40oC, non-condensing  Vibration 1 g rms/ 5-500Hz/ Random Operation (HDD)  Shock 20 G peak acceleration (11 msec. duration)  EMC CE/FCC Class A Power Supply  DC Input 84W DC 12V, with AC power adapter with lock LCD  Display Type 18.5” TFT-LCD, CCFL  Max. Resolution 1366 x 768  Max. Colors 16.7 M colors (6/8-bit for R, G, B)  Luminance (cd/m2) 300 cd/m2  Viewing Angle 170º (H), 160º (V)  Backlight CCFL

A C P - 5 1 8 5 Chapter 1 General Information 1-6  Backlight MTBF (Hours) 50,000 Touchscreen  Type Projected Capacitive Multi-Touch (Windows® 7)  Light Transmission  Lifetime (times) 90% ---

A C P - 5 1 8 5 Chapter 1 General Information 1-7 1.4 General Information 1.3M Camera (Optional) LCD On/Off RFID (Optional) Brightness- Volume- Volume+ Brightness+

A C P - 5 1 8 5 Chapter 1 General Information 1-8 VESA 100 Mounting Holes Mounting Holes

A C P - 5 1 8 5 Chapter 1 General Information 1-9 RS-232 Power Input USB x 4 VGA Line-out USB x 2 Power Switch Smart Card Reader (Optional) LAN x 2 Antenna (Optional) Antenna (Optional)

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-1 Hardware Chapter 2 Installation

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-2 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times. Place all electronic components on a static-dissipative surface or in a static-shielded bag when they are not in the chassis

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-3 2.2 A Quick Tour of the ACP-5185 Front Rear

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-4 I/O Cable Cover (Optional) Note 1: You may turn on the power by cutting and destroying the protective cover as it shows below.

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-5 Note 2: The “Anti-Drop Kit” can help on preventing the cable drop from the connector

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-6 2.3 2.5” Hard Disk Drive (HDD) Installation Step 1: Unscrew the rear cover screws (15 screws) Step 2: Remove EMI Cover (5 screws)

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-7 Step 3: Remove HDD Bracket (4 screws) Step 4: Get the HDD and HDD Bracket ready

A C P - 5 1 8 5 Chapter 2 Hardware Installation 2-8 Step 5: Fasten the four screws to fix HDD Bracket and HDD Step 6: Connect the SATA and power cables to the HDD and fasten the four screws to fix the HDD Bracket

A E C - 5 1 8 5 3.1 System Test and Iinitialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM. If system configuration is not found or system configuration data error is detected, system will load optimized default and re-boot with this default system configuration automatically. There are four situations in which you will need to setup system configuration: 1. You are starting your system for the first time 2. You have changed the hardware attached to your system 3. The system configuration is reset by Clear-CMOS jumper 4. The CMOS memory has lost power and the configuration information has been erased. The AEC-5185 CMOS memory has an integral lithium battery backup for data retention. However, you will need to replace the complete unit when it finally runs down. Chapter 3 AMI BIOS Setup 3-2

A E C - 5 1 8 5 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements. Advanced Enable disable boot option for legacy network devices. Chipset Host bridge parameters. Boot Enables/disable quiet boot option. Security Set setup administrator password. Save & Exit Exit system setup after saving the changes. Chapter 3 AMI BIOS Setup 3-3

A E C - 5 1 8 5 Setup submenu: Advanced Options summary: Disabled Optimal Default, Failsafe Default Launch 82577 PXE OpROM Enabled En/Disable Legacy Boot Option for 82577. Disabled Optimal Default, Failsafe Default Launch 82574 PXE OpROM Enabled En/Disable Legacy Boot Option for 82574. Chapter 3 AMI BIOS Setup 3-5

A E C - 5 1 8 5 PCI Subsystem Setting Options summary: 32 PCI Bus Clocks Optimal Default, Failsafe Default 64 PCI Bus Clocks 96 PCI Bus Clocks 128 PCI Bus Clocks 160 PCI Bus Clocks 192 PCI Bus Clocks 224 PCI Bus Clocks PCI Latency Timer 248 PCI Bus Clocks Value to be programmed into PCI Latency Timer Register Chapter 3 AMI BIOS Setup 3-6

A E C - 5 1 8 5 ACPI Settings Options summary: Disabled Optimal Default, Failsafe Default Enable ACPI Auto Configuration Enabled Enables or Disables BIOS ACPI Auto Configuration Disabled Enable Hibernation Enabled Optimal Default, Failsafe Default Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS. Suspend Disabled S1 only (CPU Stop Clock) ACPI Sleep State S3 only (Suspend to RAM) Optimal Default, Failsafe Default Select the highest ACPI sleep state the system will enter, when the SUSPEND button is pressed. Chapter 3 AMI BIOS Setup 3-7

A E C - 5 1 8 5 S5 RTC Wake Settings (Fixed Time) Options summary: Disabled Optimal Default, Failsafe Default Wake system with Fixed Time Enabled En/Disable System wake on alarm event. When enabled, System will wake on the hr:min:sec specified Wake up day 0-31 Default 0 Select 0 for daily system wake up, 1-31 for witch day of the moth that you would like the system to wake up. Wake up day 0-23 Default 0 Select 0-23 For example enter 3 for 3am and 15 for 3pm Wake up day 0-59 Default 0 Select 0-59 Wake up day 0-59 Default 0 Select 0-59 Chapter 3 AMI BIOS Setup 3-8

A E C - 5 1 8 5 S5 RTC Wake Settings (Dynamic Time) Options summary: Disabled Optimal Default, Failsafe Default Wake system with Dynamic Time Enabled En/Disable System wake on alarm event. When enabled, System will wake on current time + Increases minutese(s) Wake up day 1-5 Default 1 Select 1-5 Chapter 3 AMI BIOS Setup 3-9

A E C - 5 1 8 5 CPU Configuration Options summary: Disabled Hyper-Threading Enabled Optimal Default, Failsafe Default Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled. Chapter 3 AMI BIOS Setup 3-10

A E C - 5 1 8 5 IDE Configuration (RAID) Options summary: Disable IDE Optimal Default, Failsafe Default AHCI SATA Mode RAID IDE: Configure SATA controllers as legacy IDE AHCI: Configure SATA controllers to operate in AHCI mode RAID: Configure SATA controllers to operate in RAID mode Disabled Serial-ATA Controller # Enhanced Optimal Default, Failsafe Default Enable/Disable Serial ATA Controller Disabled Optimal Default, Failsafe Default Port # Hot plog Enabled SATA Ports Hot Plug Support Disabled Optimal Default, Failsafe Default External SATA Port # Enabled eSATA Ports Support Chapter 3 AMI BIOS Setup 3-13

A E C - 5 1 8 5 Options summary: 128MB 256MB Optimal Default, Failsafe Default DVMT/FIXED Memory Maximum Select DVMT/FIXED Mode Memory size used by Internal Graphics Device VBIOS Default CRT LVDS IGD – Boot Type CRT + LVDS Optimal Default, Failsafe Default Select the Video Device which will be activated during POST. This has no effect if external graphics present. LCD Panel Type 1366x768 24-bit Optimal Default, Failsafe Default Select LCD panel used by Internal Graphics Device by selecting the appropriate setup item. No LVDS Active LFP Int-LVDS Optimal Default, Failsafe Default Select the Active LFP configuration. No LVDS: VBIOS does not enable LVDS. Int-LVDS: VBIOS enables LVDS driver by Integrated encoder. Chapter 3 AMI BIOS Setup 3-15

A E C - 5 1 8 5 USB Configuration Options summary: Auto Optimal Default, Failsafe Default Floppy Forced FDD Hard Disk Device Name (Emulation Type) CDROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex. ZIP drive) Chapter 3 AMI BIOS Setup 3-16

A E C - 5 1 8 5 Serial Port 1 Configuration Options summary: Disabled Serial Port Enabled Default Allows BIOS to En/Disable correspond serial port. Auto Default IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; Change Settings IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Allows BIOS to select serial port resource. Standard Serial Port Mode Default IrDA 1.0 (HP SIR) Mode Device Mode ASKIR Mode Change the serial port mode. Chapter 3 AMI BIOS Setup 3-18

A E C - 5 1 8 5 AMT Configuration Options summary: Disabled AMT Enabled Optimal Default, Failsafe Default Intel AMT Enable/Disable Disabled Optimal Default, Failsafe Default Unconfigure AMT/ME Enabled Perform AMT/ME unconfigure without password operation Disabled Optimal Default, Failsafe Default WatchDog Timer Enabled Enable/Disable WatchDog Timer OS WatchDog Timer 0~255 (0) Optimal Default, Failsafe Default Set OS WatchDog Timer BIOS WatchDog Timer 0~255 (0) Optimal Default, Failsafe Default Set BIOS WatchDog Timer Chapter 3 AMI BIOS Setup 3-20

A E C - 5 1 8 5 CompactFlash Controller Configuration Options summary: Disabled ATA Controller IDE Mode Optimal Default, Failsafe Default Select an operative mode for ATA controller Chapter 3 AMI BIOS Setup 3-21

A E C - 5 1 8 5 Serial Port Condole Redirection Options summary: Disabled Optimal Default, Failsafe Default Console Redirection Enabled Console Redirection Enable/Disable Chapter 3 AMI BIOS Setup 3-22

A E C - 5 1 8 5 Options summary: 64M Optimal Default, Failsafe Default Low MMIO Align 1024M Low MMIO resource align at 64MB/1024MB IGD PCI/IGD PCI/PEG PEG/IGD Optimal Default, Failsafe Default Initiate Graphic Adapter PEG/PCI Select which graphics controller to use as the primary boot device Graphics Turbo IMON Current 14~31(31) Optimal Default, Failsafe Default Graphics turbo IMON current values supported Disabled Optimal Default, Failsafe Default VT-d Enabled Check to enable VT-d function on MCH Disabled Optimal Default, Failsafe Default PCI Express Compliance Mode Enabled PCI Express Compliance Testing Mode Disabled Isoch Enabled Optimal Default, Failsafe Default Isoch Enable/Disable Disabled Optimal Default, Failsafe Default MarginRanks Enable Enabled MarginRanks Enable/Disable Disabled Enabled PCI Express Port Auto Optimal Default, Failsafe Default PCI Express Enable/Disable Disabled 32M Optimal Default, Failsafe Default 64M IGD Memory 128M UGD Share Memory Size Disabled Optimal Default, Failsafe Default PAVP Mode Enabled Select PAVP Mode used by Internal Graphics Device Disabled Optimal Default, Failsafe Default PEG Force Gen1 Enabled PCI Express Port Force Gen1 Chapter 3 AMI BIOS Setup 3-25

A E C - 5 1 8 5 Options summary: Disabled 82577 SMBus Controller Enabled Optimal Default, Failsafe Default 82577 SMBus Controller Enable/Disable Disabled 82577 GbE Controller Enabled Optimal Default, Failsafe Default 82577 GbE Controller Enable/Disable Disabled 82577 Wake on LAN from S5 Enabled Optimal Default, Failsafe Default 82577 Wake on LAN from S5 Enable/Disable Power Off Optimal Default, Failsafe Default Power On Restore AC Power Loss Last State Select AC power state when power is re-applied after a power failure. Disabled SLP_S4 Assertion Stretch Enable Enabled Optimal Default, Failsafe Default Select a minium assertion width of the SLP_S4# signal 1 - 2 Seconds 2 - 3 Seconds 3 - 4 Seconds SLP_S4 Assertion Width 4 - 5 Seconds Optimal Default, Failsafe Default Select SLP_S4 assertion width Disabled Azalia Enabled Optimal Default, Failsafe Default Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled; Enabled = Azalia will be unconditionally enabled Chapter 3 AMI BIOS Setup 3-27

A E C - 5 1 8 5 ME Subsystem Options summary: Disabled ME Subsystem Enabled Optimal Default, Failsafe Default ME Subsystem Enable/Disable Disabled End of Post Message Enabled Optimal Default, Failsafe Default End of Post Message Enable/Disable Disabled Execute MEBx Enabled Optimal Default, Failsafe Default Execute MEBx Enable/Disable Chapter 3 AMI BIOS Setup 3-28

A E C - 5 1 8 5 Options summary: Disabled Optimal Default, Failsafe Default Quiet Boot Enabled En/Disable showing boot logo. Setup Prompt Timeout 1~65535 (1) Optimal Default, Failsafe Default Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. On Optimal Default, Failsafe Default Bootup NumLock State Off Select the keyboard NumLock state Upon Request Optimal Default, Failsafe Default GateA20 Active Always UPON REQUEST – GA20 can be disabled using BIOS services. ALWAYS – Do not allow disabling GA20; This option is useful when any RT code is executed above 1MB. Force BIOS Optimal Default, Failsafe Default Option ROM Messages Keep Current Set display mode for Option ROM. Chapter 3 AMI BIOS Setup 3-30

A E C - 5 1 8 5 Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. A second dialog box asks you to retype the password for confirmation. Press Enter after you have retyped it correctly. The password is required at boot time, or when the user enters the Setup utility. Removing the Password Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection. Chapter 3 AMI BIOS Setup 3-32

A C P - 5 1 8 5 Chapter 4 Driver Installation 4-1 Driver Chapter 4 Installation

A C P - 5 1 8 5 The ACP-5185 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install ME Driver Step 5 – Install Audio Driver Step 6 – Install Touch Driver (For Windows® XP only) Step 7 – Install Smart Card Reader Driver (Optional) Step 8 – Install WiFi & Bluetooth Driver (Optional) Step 9 – Install RAID & AHCI Driver Please read instructions below for further detailed installations. Chapter 4 Driver Installation 4-2

A C P - 5 1 8 5 4.1 Installation: Insert the ACP-5185 DVD-ROM into the DVD-ROM drive. Then install the drivers from Step 1 to Step 9 in order. Step 1 – Install Chipset Driver 1. Click on the Step1–CHIPSET folder and double click on the infinst_autol(9.1.1.1020).exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step2–VGA folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 3 – Install LAN Driver 1. Click on the Step3–LAN folder and double click on the Autorun.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Chapter 4 Driver Installation 4-3

A C P - 5 1 8 5 Step 4 –Install ME Driver 1. Click on the Step4–ME folder and double click on the Setup.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 5 – Install Audio Driver 1. Click on the Step5–AUDIO folder double click on the SETUP.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 6 – Install Touch Driver (For Windows® XP only) 1. Click on the Step6–Touch folder and double click on the ModifyDBArea file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 7 – Install Smart Card Reader Driver (Optional) 1. Click on the Step7–SMART CARD READER folder and select the OS folder your system is 2. Double click on the setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Chapter 4 Driver Installation 4-4

A C P - 5 1 8 5 Step 8 – Install WiFi & Bluetooth Driver (Optional) 1. Click on the Step8–WIFI&BLUETOOTH folder and select the OS folder your system is 2. Double click on the .exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 9 – Install RAID & AHCI Driver Setting RAID OS installation to setup RAID Mode Step 1: Copy the files below from “Driver CD ->Step7- RAID & AHCI” to Disk Chapter 4 Driver Installation 4-5

A C P - 5 1 8 5 Step 2: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 3: The setting procedures “In BIOS Setup Menu” B: Advanced -> Launch Storage OpROM -> Enabled Chapter 4 Driver Installation 4-6

A C P - 5 1 8 5 Step 4: The setting procedures “In BIOS Setup Menu” C: Boot -> Boot Option #1 -> DVD-ROM Type Step 5: The setting procedures “In BIOS Setup Menu” D: Save & Exit -> Save Changes and Exit Chapter 4 Driver Installation 4-7

A C P - 5 1 8 5 Step 6: Press Ctrl-I to enter MAIN MENU Step 7: Choose “1.Create RAID Volume” Chapter 4 Driver Installation 4-8

A C P - 5 1 8 5 Step 8: RAID Level -> RAID0(Stripe) Step 9: Choose “Create Volume” Chapter 4 Driver Installation 4-9

A C P - 5 1 8 5 Step 10: Choose “Y” Step 11: Choose “5. Exit” Chapter 4 Driver Installation 4-10

A C P - 5 1 8 5 Step 12: Choose “Y” Step 13: Setup OS Chapter 4 Driver Installation 4-11

A C P - 5 1 8 5 Step 14: Press “F6” Step 15: Choose “S” Chapter 4 Driver Installation 4-12

A C P - 5 1 8 5 Step 16: Choose “Intel(R) Mobile Express Chipset SATA RAID Controller” Step 17: It will show the model number you select and then press “ENTER” Chapter 4 Driver Installation 4-13

A C P - 5 1 8 5 Step 18: Setup is starting Windows Setting AHCI OS installation to setup AHCI Mode Step 1: Copy the files below from “Driver CD -> Step7- RAID & AHCI” to Disk Chapter 4 Driver Installation 4-14

A C P - 5 1 8 5 Step 2: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 3: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Chapter 4 Driver Installation 4-15

A C P - 5 1 8 5 Step 4: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 5: Setup OS Chapter 4 Driver Installation 4-16

A C P - 5 1 8 5 Step 6: Press “F6” Step 7: Choose “S” Chapter 4 Driver Installation 4-17

A C P - 5 1 8 5 Step 8: Choose “Intel(R) 7 Series Chipset Family SATA AHCI Controller” Step 9: It will show the model number you select and then press “ENTER” Chapter 4 Driver Installation 4-18

A C P - 5 1 8 5 Chapter 4 Driver Installation 4-19 Step 10: Setup is loading files

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-1 Appendix A Programming the Watchdog Timer

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-2 A.1 Programming ACP-5185 utilizes ITE 8781 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized programs to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8781 enters the normal mode with all logical devices disabled except KBC. The initial state (enable bit ) of this logical device (KBC) is determined by the state of pin 121 (DTR1#) at the falling edge of the system reset during power-on reset.

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-3 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step. (2) Modify the Data of the Registers All configuration registers can be accessed after entering the MB PnP Mode. Before accessing a selected register, the content of Index 07h must be changed to the LDN to which the register belongs, except some Global registers. (3) Exit the MB PnP Mode Set bit 1 of the configure control register (Index=02h) to 1 to exit the MB PnP Mode.

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-4 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them. Watch Dog Timer 1, 2, 3 Control Register (Index=71h,81h,91h Default=00h)

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-5 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h)

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-6 A.2 ITE8781 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second. mov al, 0C0H mov cl, 72h call Superio_Set_Reg

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-7 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-8 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-9 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.Set_Logic_Device proc near Set_Logic_Device proc near

A C P - 5 1 8 5 Appendix A Programming the Watchdog Timer A-10 push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . . 03h: IRQ3 02h: not valid 01h: IRQ1 00h: no interrupt selected

A C P - 5 1 8 5 Appendix B I/O Information B - 5 B.3 IRQ Mapping Chart B.4 DMA Channel Assignments

A C P - 5 1 8 5 Appendix C Miscellanea C-1 Miscellanea A ppendix C

A C P - 5 1 8 5 Appendix C Miscellanea C-2 C.1 General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. 1. Never spray or squirt the liquids directly onto any computer component. If you need to clean the device, please rub it with a piece of dry cloth. 2. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor. 3. Turn the system off before you start to clean up the component or computer. 4. Never drop the components inside the computer or get circuit board damp or wet. 5. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of cleaning. Some individuals may be allergic to the ingredients. 6. Try not to put any food, drinks or cigarettes around the computer.

A C P - 5 1 8 5 Appendix C Miscellanea C-3 C.2 Cleaning tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals. Keep in mind that some components in your computer may only be able to be cleaned using a product designed for cleaning that component, if this is the case it will be mentioned in the cleaning tips.  Cloth - A piece of cloth is the best tool to use when rubbing up a component. Although paper towels or tissues can be used on most hardware as well, we still recommend you to rub it with a piece of cloth.  Water or rubbing alcohol – You may moisten a piece of cloth a bit with some water or rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the plastics parts.  Vacuum cleaner - Absorb the dust, dirt, hair, cigarette particles, and other particles out of a computer can be one of the best methods of cleaning a computer. Over time these items can restrict the airflow in a computer and cause circuitry to corrode.