GLP IMPRESSION WWC STATIC Instruction Manual

(Instruction version 1.00) e-mail: [email protected] Internet: http://www.glp.de W W WW W WC CC & & & C CCC CCW W W SSStttaaatttiiiccc

(Instruction version 1.00) / from software version 1.00/30) 2 Preface This manual serves for both systems the IIM MPPRREESSSSIIO ONN W WW WCC as well as the IIM MPPRREESSSSIIO ONN CCCCW W.. The two systems differ from each other only by the number of cold- respectively warm- white LEDs. WWC version: 30x LEDs cold white, 60x LEDs warm white CCW version: 60x LEDs cold white, 30x LEDs warm white Notes:

(Instruction version 1.00) / from software version 1.00/30) 3 Table of content 1 Description of Device.............................................................................................. 4 1.1 Safety Instructions ............................................................................................ 5 2 Preparation and Installation ................................................................................... 6 2.1 Mounting ........................................................................................................... 6 2.1.1 Mounting on the Floor (Upright) ........................................................... 7 2.1.2 Mounting in hanging Position (Head first) ............................................ 7 2.1.3 Mounting in sidewise Position .............................................................. 8 2.2 Secure the Device ............................................................................................ 9 2.3 Connections ...................................................................................................... 9 2.3.1 Power Supply....................................................................................... 9 2.3.2 DMX ..................................................................................................... 9 3 The Menu Field ...................................................................................................... 10 4 DMX Channel Selection (DMX Protocol) ............................................................. 11 55 Maintaining and Cleaning the IIM MPPRREESSSSIIO ONN ....................................................... 14 5.1 Safety regulations ........................................................................................... 14 5.2 Circumference and Interval (rule-of-thumb) .................................................... 14 6 Technical Specifications ...................................................................................... 15 7 Index ....................................................................................................................... 16

(Instruction version 1.00) / from software version 1.00/30) 4 1 Description of Device 1. Moving head (actively and passively cooled) 2. Arm with various cooling vents 3. LCD-Display/Menu (data entry) 4. Base with various connectors and Camlock mounting system 1 2 3 4 5 ba se sid e 1 6 base side 2 7 8 9 10 10 FUSE T4A 5. Power On/Off 6. DMX- Output (3 pole) 7. DMX- Input (3 pole) 8. Micro-fuse 5x20mm, T4A 9. Mains supply (Powercon) 10. 2x Safety eyes

(Instruction version 1.00) / from software version 1.00/30) 5 1.1 Safety Instructions The IIM MPPRREESSSSIIO ONN is a High-Tech Product. To guarantee a smooth operation, it is necessary to respect the following rules. The manufacturer of this device will not take responsibility of damages through any disregard of the information in this manual. Warranty claims also will be cancelled in case the system casing is opened. 1. Make sure before putting the system into operation, that the fan and the air inlets are clean and not blocked by anything. 2. It must be assured that the system-head can rotate unhindered throughout his complete rotating range. A safety distance of at least 0.5 m to any easily inflammable material (e.g. decoration material) must be adhered. 3. Attention! Don’t touch the device during the operation. This can cause injuries or damages. 4. The system doesn’t contain any maintainable parts. Don’t open it! 5. It is necessary to wait at least 15 minutes after disconnecting the AC before changing the optical carrier. Pay attention to possibly hot parts of the system. -- Danger of BURNING -- 6. Never look directly into the beam of light or one of the LEDs. Never use optical apertures with a distance less than 0.5 m to observe the beam of light. LED Class 2M. You'll risk a serious injury of your eyes and in particular of your retina. Attention: LED Class 2M can cause injuries of your eyes even without optical instruments in front of them or within a distance of less than 0.5m and short exposure time. Hence: Avoid direct radiation of your eyes! 7. To allow a secure operation, follow also the Installation guide described in chapter 2. Operating the IIM MPPRREESSSSIIO ONN without suitable safety aids like Safety cables or clamps/hooks can increase the risk of an accident. 8. Repair-, maintenance- and installation work shall be done by qualified or GLP certified staff only. You need to pay attention to the common rules of technology that are not explicit mentioned in this manual. 9. Use only original spare parts. Any structural modification on the system will terminate all warranty claims.

(Instruction version 1.00) / from software version 1.00/30) 6 2 Preparation and Installation 2.1 Mounting The IIM MPPRREESSSSIIO ONN is fully operational whether it hangs or is mounted to the wall. It can also be operated while standing on the floor. Keep a safety distance of 0.5 m towards any easily inflammable materials (decoration etc.). Pay attention to the regulations of: BGV C1 (former VBG 70) and DIN VDE 0711-217. The installation shall be done by qualified staff only. For the various mounting positions of the IIM MPPRREESSSSIIO ONN (standing on the floor, sideways or hanging) different accessories kits are available. Through this a safe and firm installation is assured. You'll find special connectors on the bottom side of the system which are put to use here. In addition the front side of the system is marked with (FRONT) as this is important for a even orientation during installation.

(Instruction version 1.00) / from software version 1.00/30) 7 1x M10 (length max.16mm) 2x Camlock quick release fasteners front side of the fixture 2.1.1 Mounting on the Floor (Upright) To operate the IIM MPPRREESSSSIIO ONN in an upright position, please use the dedicated tripod which is mounted to the bottom side of the system. It is fixed with fasteners called Camlock quick-release connectors. Turn the two fasteners both 90° to lock them. Do the opposit e to release them again. On both sides you'll find eyelets to pull though a fixing strap. This allows an additional bracing of the system during the upright operation. 2x Camloc k 2x eyelets 2.1.2 Mounting in hanging Position (Head first) To operate the IIM MPPRREESSSSIIO ONN in an hanging position, please use a half- coupler (clamp) which is mounted directly to the bottom side of the system. It is fixed centrically with a M10x16 mm thread bolt.

(Instruction version 1.00) / from software version 1.00/30) 8 M10x16 2.1.3 Mounting in sidewise Position To operate the IIM MPPRREESSSSIIO ONN in a sidewise position, please use an addition mounting bar. Also this is fixed by two Camlock quick-release connectors. Two half-couplers (clamps) are now used to mount the system to a standard truss bar. This technique is necessary to cope with the torque which accrues in this mounting position. In addition it allows a concentrically position between two truss belts. Never use the "Mounting in hanging Position" technique described above to fasten the system in the sidewise position. A safe and sound installation can not be assured in this way. This can also damage the system base. 2x 90° Half-coupler (clamp) 1 Half-coupler (clamp) 2

(Instruction version 1.00) / from software version 1.00/30) 9 without mounting bar 2.2 Secure the Device Regardless of the mounting method of the IIM MPPRREESSSSIIO ONN you'll have to use a stipulated safety wire. Therefore you have to pull the safety wire through to two provided holes on the bottom side of the system and connect it with the truss- support. Pay attention to a safe and proper fastening. Install a safety wire that can hold at least 10 times the weight of the fixture. Never use the carrying handles for this purpose. The safety wire must be attached in a way that the height of drop is minimised. A height of drop of more that 0.2m is strictly forbidden (    BGI 810-3). 2.3 Connections 2.3.1 Power Supply ~100-240 Volt AC, 50-60 Hz, earth contact type plug - Powercon Connected load 350 VA (W) <=> T4A (micro-fuse 5x20mm) Please see printing on the case for the right electronic supply! Disconnect from the mains supply for changing the fuse and use only the above described micro-fuse type. 2.3.2 DMX USITT DMX-512 Standard input/output in 3 pole connectors. 3 pole: Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+] The DMX- Addressing starts at the DMX- Address [001].

(Instruction version 1.00) / from software version 1.00/30) 10 3 The Menu Field You’ll find the control board on the side part of the arm. It allows you to make all necessary adjustments of the IIM MPPRREESSSSIIO ONN.. With the Mode- key you get into the main menu. Afterwards you can navigate through the menu with the Up/Down-keys. Push the Enter-key to get in the next menu level or to confirm your settings. Make them and set functions ON/OFF with the Up/Down-keys. Confirm and save it with the Enter-key (the display shows OK). Push the Mode-key to cancel the entry and go back to the main menu. Mode Down Enter Up     MODE - ENTER     Level1 Level 2 Level 3 Level 4 Remark DMX Start Address Define the DMX start address Special Manual DMX Manual control of all system functions Special Activate the White- or Full-Power Mode; see also DMX table Dimmer Manual control for Dimmer     DOWN - UP     Shutter Manual control for Shutter 1/3 White Manual control for 1/3 white, 30x LEDs (either warm- or cold white depending on the system) 2/3 White Manual control for 2/3 white, 60x LEDs (either warm- or cold white depending on the system) Display Contrast Adjustment for the Display contrast Default Set Resetting all functions to original values Set Dimmer Frequency Changes PMW frequency between 600Hz and 1200Hz Adjust Key code xxxx Use the code for entering the calibration menu (for authorized persons only) Clear EEPROM Erase EEPROM memory Diagnose Diagnose functions Anz Ti0-Int- Err Internal data and function diagnosis Dimmerwert für DIM1 Internal data and function diagnosis Dimmerwert für DIM2 Internal data and function diagnosis Dimmerwert für DIM3 Internal data and function diagnosis PFC Voltage Shows the present PFC voltage Temperature Arm Indicates the arm temperature Temperature Head Indicates the head temperature DMX Hold Defines whether the last DMX signal is stored or the lamp is switched OFF in case of signal interruption Position Feedback Automatically position feedback (correction) for Pan/Tilt movement Set DMX Image Stores the Scene currently sent to the unit

(Instruction version 1.00) / from software version 1.00/30) 11 DMX input Monitor Indicates the presently received DMX signal per DMX channel Special Current value for Special Dimmer Current value for Dimmer Shutter Current value for Shutter 1/3 White Current value for 1/3 White, 30x LEDs (either warm- or cold white depending on the system) 2/3 White Current value for 2/3 White, 60x LEDs (either warm- or cold white depending on the system) Self Test Performs an automatic self-test Live time Indicates the overall operation time of the system Display Adjust the display Blackout ON/OFF: Display OFF Select DMX Mode Please select the desired DMX Mode Compressed Only 5 DMX channels are being used if this Mode is activated Normal 4 DMX channels are being used if this Mode is activated High- Resolution 7 DMX channels are being used if this Mode is activated. Dimmer operates at 16 bit. Reset RESET and new calibration for all functions 4 DMX Channel Selection (DMX Protocol) Normal-Mode 5 DMX channels Channel Function Time and Value DMX HEX % 1) White 2/3 White Color, 60x LEDs (either warm- or cold white depending on the system) 0 - 100% 0..255 00..FF 0..100 2) White 1/3 White Color, 30x LEDs (either warm- or cold white depending on the system) 0 - 100% 0..255 00..FF 0..100 3) Shutter Shutter closed 0..15 00..0F 0..5,5 Random Pulse effect slow - fast 16..47 10..2F 6..18,5 Up-dimming then Shutter closing (random patterns) slow - fast 48..79 30..4F 19..31 Shutter open then down-dimming (random patterns) slow - fast 80..111 50..6F 32..43 Up-dimming then down-dimming (random patterns) slow - fast 112..143 70..8F 44..56 Strobe effect, stop break 5 sec. - 1 sec. 144..199 A0..C7 57..77 Strobe effect, slow - fast 1 Hz .. 10 Hz 200..239 C8..EF 78..94 Shutter open 240..255 F0..FF 95..100 4) Dimmer Dimmer 0 - 100% 0..255 0..FF 0..100 5) Special Fan min. as long as temp. < 60°C 224..249 E0..E5 88..89,5 RESET (Normal Mode) 250..255 FA..FF 98..100

(Instruction version 1.00) / from software version 1.00/30) 12 Compress-Mode 4 DMX channels Channel Function Time and Value DMX HEX % 1) White 2/3 White Color, 60x LEDs (either warm- or cold white depending on the system) 0 - 100% 0..255 00..FF 0..100 2) White 1/3 White Color, 30x LEDs (either warm- or cold white depending on the system) 0 - 100% 0..255 00..FF 0..100 3) Shutter Shutter closed 0..15 00..0F 0..5,5 Random Pulse effect slow - fast 16..47 10..2F 6..18,5 Up-dimming then Shutter closing (random patterns) slow - fast 48..79 30..4F 19..31,5 Shutter open then down-dimming (random patterns) slow - fast 80..111 50..6F 32..43 Up-dimming then down-dimming (random patterns) slow - fast 112..143 70..8F 44..56 Strobe effect, stop break 5 sec. - 1 sec. 144..199 A0..C7 57..77 Strobe effect, slow - fast 1 Hz .. 10 Hz 200..239 C8..EF 78..94 Shutter open 240..249 F0..F9 95..97,5 RESET Min. 3 Sec. 250 FA 98 4) Dimmer Dimmer 0 - 100% 0..255 0..FF 0..100 High Resolution (Extended)- Mode 11 DMX Channels Channel Function Time and Value DMX HEX % 1) White 2/3 coarse White Color, 60x LEDs (either warm- or cold white depending on the system) 0 - 100% 0..255 00..FF 0..100 2) White 2/3 fine White - fine/low 0..255 00..FF 0..100 3) White 1/3 coarse White Color, 30x LEDs (either warm- or cold white depending on the system) 0 - 100% 0..255 00..FF 0..100 4) White 1/3 fine White - fine/low 0..255 00..FF 0..100 5) Shutter Shutter closed 0..15 00..0F 0..5,5 Random Pulse effect slow - fast 16..47 10..2F 6..18,5 Up-dimming then Shutter closing (random patterns) slow - fast 48..79 30..4F 19..31,5 Shutter open then down-dimming (random patterns) slow - fast 80..111 50..6F 32..43 Up-dimming then down-dimming (random patterns) slow - fast 112..143 70..8F 44..56 Strobe effect, stop break 5 sec. - 1 sec. 144..199 A0..C7 57..77 Strobe effect, slow - fast 1 Hz .. 10 Hz 200..239 C8..EF 78..94 RESET Min. 3 Sec. 250 FA 98 6) Dimmer- coarse Dimmer - coarse/high 0 - 100% 0..255 0..FF 0..100 7) Dimmer- fine Dimmer - fine/low 0..255 0..FF 0..100

(Instruction version 1.00) / from software version 1.00/30) 13 Locking and unlocking the Control Panel Please lock and unlock the control panel by pressing the menu keys MODE & ENTER & UP at the same time. Additional features during switching-ON the system a) 1200Hz Mode (Hold down the UP- button during power ON) After switching ON the system the LEDs will be operated with a Pulse Width Modulation (PWM) of 1200Hz. In addition all standard setting will be loaded (DMX start address [001] and Normal Mode. b) 600Hz Mode (Hold down the DOWN- button during power ON) After switching ON the system the LEDs will be operated with a Pulse Width Modulation (PWM) of 600Hz. In addition all standard setting will be loaded (DMX start address [001] and Normal Mode. c) Standard Mode (Hold down the ENTER- button during power ON) After switching ON the system the DMX start address will be set to [001]. All other setting remain unchanged. Additional Display Indication As a default you'll find the following additional information in the first row of the LCD display: XX/X/XX 06 = 600Hz / 12 = 1200Hz N = Normal Mode / C = Compressed Mode / H = High Res. Mode N = Tilt normal / I = Tilt inverted N = Pan normal / I = Pan inverted

(Instruction version 1.00) / from software version 1.00/30) 14 55 Maintaining and Cleaning the IIM MPPRREESSSSIIO ONN The IIM MPPRREESSSSIIO ONN is a system of very low maintenance. It is only necessary to clean the air in- and outlets as well as the optical LED lenses from time to time. For a safe operation it is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not built up on or within the fixture. Otherwise the fixture's light-output will be significantly reduced or damages can occur. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to operate reliably throughout its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recom- mended, under no circumstances should alcohol or solvents be used! 5.1 Safety regulations • Pull out the main plug! • Wait min. 15 minutes after the last operation to cool down the fixture. 5.2 Circumference and Interval (rule-of-thumb) The contamination of the fixture depends on the environment details. Hence no general guidelines can be given. The intervals given below are only suggestions from our practice experience. Position Interval In this way LED reflector and optical system weekly soft brush /lint-free cloth Fan and air channel monthly vacuum cleaner, airbrush, etc. Attention: • Never let optical parts come into contact with oil or fat. • Before running the fixture wait until all parts are dried up. • Never tough lenses with bare fingers.

(Instruction version 1.00) / from software version 1.00/30) 15 6 Technical Specifications Power supply Power consumption 350 VA (Watt) Power Input ~100-240 V AC, 50-60 Hz (wide range input) Fuse protection Micro-fuse 5x20 mm, T4A Operational Parameters Max. Ambient Temperature 45°C (integrated overheating switch) Mounting Position Any (see chapter mounting) Lighting System - Additive Color mixing (8/16 Bit) LED Type 90x Luxeon K2 High-power- LEDs Lifetime 50.000 h     CCW version: 60x LEDs cold white, 30x LEDs warm white     WWC version: 30x LEDs cold white, 60x LEDs warm white Optical System High efficient Collimator cluster Exchangeable optical carrier with 10° light distrib ution angle (25° optional) Scattering light aperture Shutter / Dimmer (8 Bit) Strobe- Effect with variable speed between 1 - 10 flashes per second, Random-Strobe, Pulse- Effects Continuous Dimmer 0 - 100% DMX Control Standard USITT DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1. Die DMX- Addressing starts at the DMX channel [001]. Pan / Tilt (8/16 Bit) Pan- movement 660° in min. 3,2 seconds (Position Feedback) Tilt- movement 300° in min. 1,5 seconds (Position Feedback) Weights and Measures Width of the base 340 mm Length of the base 145 mm height (head vertical) 370 mm Weight (net) 7,5 kg

(Instruction version 1.00) / from software version 1.00/30) 16 7 Index 1 1200Hz Mode ................................................ 13 6 600Hz Mode .................................................. 13 B BGI 810-3 ........................................................ 9 BGV C1............................................................ 6 C Camlock ........................................................... 7 CCW version .................................................. 2 Circumference ............................................... 14 Cleaning......................................................... 14 Cold white LEDs .............................................. 2 Compress-Mode .......................................... 12 D Danger of BURNING ...................................... 5 Description of Device ....................................... 4 DIN VDE 0711-217 .......................................... 6 DMX ................................................................. 9 DMX Protocol ................................................ 11 E e-mail ............................................................... 1 Enter-key ....................................................... 10 Eyelets ............................................................. 7 H Half-couplers (clamps) ..................................... 8 I Instruction Version ........................................... 1 Internet............................................................. 1 L LED Class 2M ................................................. 5 Locking the Control Panel .......................... 13 Luxeon K2 ..................................................... 15 M Maintenance ................................................. 14 Menu Field .................................................... 10 Micro-fuse ....................................................... 9 Mode-key ...................................................... 10 Mounting ........................................................ 6 Mounting in hanging Position .......................... 7 Mounting in sidewise Position ......................... 8 Mounting on the Floor ..................................... 7 N Normal-Mode ............................................... 11 O Optical parts ................................................ 14 P Pan- Movement ............................................. 15 Power Supply ................................................ 9 Powercon ........................................................ 4 S Safety distance ............................................... 6 Safety Instructions .......................................... 5 Secure the Device ......................................... 9 Software Version ............................................. 1 T Technical Specifications ............................ 15 Tilt- Movement .............................................. 15 U Up/Down-keys .............................................. 10 V VBG 70 ........................................................... 6 W Warm white LEDs ........................................... 2 Warranty claims .............................................. 5 Weights and Measures ................................. 15 WWC version ................................................. 2

(Instruction version 1.00) / from software version 1.00/30) 17