Aria Child W488AC Owner's Manual

1. Disconnect the red battery connector (A) from the red engine connector (B) 2. Loosen and remove the screw 3. Unfasten the battery from the strap 4. Remove the battery. Note: It is not necessary to remove the battery for charging. However, if the battery does not reach the outlet, it can be removed for charging. Screw Battery Strap Battery B A ...

condition. • Regularly inspect the charger, cord, plug, and other related parts for damage. • Remove any damaged parts and immediately contact Customer Service for replacement parts. See Service and Repairs on Page 24 for more information. • DO NOT operate the vehicle if there are any damaged parts. • Carefully clean the vehicle with a damp cloth and mild soap. Do not get water in or near any electrical parts. Do not wash the vehicle with a hose. • Store the vehicle indoors or use a tarp to cov ...

1. Slide the right rear wheel (17) onto right rear wheel axle. The side with gear teeth faces inward. (Note: the gear teeth must engage with the gear box.) 2. Slide the rear flat washer (19) onto the right rear axle. 3. Slide the snap pin (20) into the hole on the right rear axle until firmly attached. 4. Snap the rim (21) onto the right wheel. 5. Snap the hub cap (22) onto the completed wheel assembly. Assemble the Right Rear Wheel Helpful Tip: 1. If you encounter trouble fitting both wheels onto the rear axle, then your rear wheel axle may need to be realigned. 2. ...

condition. • Regularly inspect the charger, cord, plug, and other related parts for damage. • Remove any damaged parts and immediately contact Customer Service for replacement parts. See Service and Repairs on Page 24 for more information. • DO NOT operate the vehicle if there are any damaged parts. • Carefully clean the vehicle with a damp cloth and mild soap. Do not get water in or near any electrical parts. Do not wash the vehicle with a hose. • Store the vehicle indoors or use a tarp to cov ...

Left Rear Wheel: 1. Slide the rear thick washer (18) onto the left rear axle. 2. Slide the orientation sleeve onto the left rear wheel axle. 3. Slide the left rear wheel (17) onto the left rear axle. The side with the gear teeth faces inward. 4. Slide the rear flat washer (19) onto the left rear axle. 5. Slide the snap pin (20) into the hole on the left rear axle until firmly attached. 6. Snap the rim (21) onto the left wheel assembly. 7. Snap the hub cap (22) onto the completed left wheel assembly. 18 17 19 20 21 22 ...

1. Slide the front thick washer (18) onto the front axle. 2. Slide the front wheel (16) onto the front axle. 3. Slide the front flat washer (19) onto the front axle. 4. Slide the snap pin (20) into the hole on the front axle until firmly attached. Tip: Pliers may be helpful when removing the snap pin. 5. Snap the rim (21) onto the wheel. 6. Snap the hub cap (22) onto the completed wheel assembly. 7. Repeat steps 1-6 for the remaining front wheel. 18 16 19 20 21 22 Helpful Tip: 1. Using pliers will make it easier to remove the snap pin from the wheel axle ...

1. Remove the screw and nut from the steering wheel assembly before attaching 2. Insert the steering wheel (10) into the steering rod, and match the screw holes of the steering wheel with the screw holes on the steering rod 3. Insert the screw into the hole and fasten the nut to secure Steering wheel requires 2 x 1.5v AA/LR06 batteries 1. Open the battery compartment cover with the screwdriver 2. Insert the two batteries into the battery compartment 3. Replace the battery compartment cover and securely close with the screw Note: If steering wheel sounds become d ...

To Charge the Battery: 1. Ensure the car is stopped and turned off. 2. Unlock and remove the seat. 3. Unplug the red battery connector (A) from the red engine connector (B). 4. Connect the red battery connector (A) to the red battery charger connector (C) and plug (D) into a 120 V outlet. To Unplug the Battery: 1. Unplug the battery charger (D) from the outlet. 2. Unplug the red battery connector (A). 3. Reconnect the red battery connector (A) to the red engine connector (B). 4. Replace the seat and tighten lo ...