Wacker Neuson GV 6600A Operator's Manual

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot see or smell. If you can smell the generator exhaust, you are breathing CO. But even if you cannot smell the exhaust, you could be breathing CO. • NEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or opening windows and doors does NOT supply enough fresh air. • ONLY use a generator outside and far away from windows, doors, and vents. These openings can pull in generator exhaust. Even when you use a generator correctly, CO may leak into the home. ALWAYS use a battery-powered or battery-backup CO alarm in the home. If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh air RIGHT AWAY. See a doctor. You could have carbon monoxide poison.

wc_bo0170814en_003TOC.fm 3 1. Foreword 5 2. Safety Information 6 2.1 Laws Pertaining to Spark Arresters ...................................................... 6 2.2 Operating Safety .................................................................................. 7 2.3 Operator Safety while using Internal Combustion Engines .................. 9 2.4 Service Safety .................................................................................... 10 2.5 Label Locations .................................................................................. 11 2.6 Safety and Operating Labels .............................................................. 12 3. Operation 15 3.1 Determining Power Requirements ..................................................... 15 3.2 Installation .......................................................................................... 16 3.3 Installing Spark Arrester ..................................................................... 16 3.4 Generator Derating ............................................................................. 17 3.5 Grounding the Generator ................................................................... 18 3.6 Operating Heavy Loads ...................................................................... 18 3.7 Use of Extension Cords ...................................................................... 19 3.8 Control Panel ...................................................................................... 20 3.9 Ground Fault Interrupt (GFI) ............................................................... 21 3.10 Main Circuit Breaker ........................................................................... 21 3.11 Voltage Selection ............................................................................... 22 3.12 Engine Auto Idle ................................................................................. 22 3.13 Before Starting ................................................................................... 23 3.14 To Start ............................................................................................... 24 3.15 To Stop ............................................................................................... 25

GV 6600A wc_bo0170814en_003TOC.fm 4 4. Maintenance 26 4.1 Engine Maintenance ............................................................................26 4.2 Periodic Maintenance Schedule ..........................................................26 4.3 Engine Oil ............................................................................................27 4.4 Servicing Air Cleaner ...........................................................................28 4.5 Spark Plug ...........................................................................................29 4.6 Cleaning the Sediment Cup ................................................................30 4.7 Storage ................................................................................................31 4.8 Transport .............................................................................................32 4.9 Troubleshooting ...................................................................................33 5. Technical Data 34 5.1 Generator ............................................................................................34 5.2 Engine .................................................................................................35 5.3 Electrical Schematic ............................................................................36 5.4 Schematic Components ......................................................................37

Engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 1. Foreword This manual provides information and procedures to safely operate and maintain this Wacker model. For your own safety and protection from injury, carefully read, understand and observe the safety instructions described in this manual. Keep this manual or a copy of it with the machine. If you lose this manual or need an additional copy, please contact Wacker Corporation. This machine is built with user safety in mind; however, it can present hazards if improperly operated and serviced. Follow operating instructions carefully! If you have questions about operating or servicing this equipment, please contact Wacker Corporation. The information contained in this manual was based on machines in production at the time of publication. Wacker Corporation reserves the right to change any portion of this information without notice. All rights, especially copying and distribution rights, are reserved. Copyright 2007 by Wacker Corporation. No part of this publication may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission from Wacker Corporation. Any type of reproduction or distribution not authorized by Wacker Corporation represents an infringement of valid copyrights and will be prosecuted. We expressly reserve the right to make technical modifications, even without due notice, which aim at improving our machines or their safety standards. WARNING

NOTE callouts which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE: Used without the safety alert symbol, NOTICE indicates a hazardous situation which, if not avoided, could result in property damage. Note: Contains additional information important to a procedure. 2.1 Laws Pertaining to Spark Arresters Notice: State Health Safety Codes and Public Resources Codes specify that in certain locations spark arresters be used on internal combustion engines that use hydrocarbon fuels. A spark arrester is a device designed to prevent accidental discharge of sparks or flames from the engine exhaust. Spark arresters are qualified and rated by the United States Forest Service for this purpose. In order to comply with local laws regarding spark arresters, consult the engine distributor or the local Health and Safety Administrator. DANGER WARNING CAUTION

exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use this generator inside a home or garage, EVEN IF doors and windows are open. Only use this generator OUTSIDE and far away from windows, doors, and vents. BACKFEED FROM THE GENERATOR INTO THE PUBLIC POWER DISTRIBUTION SYSTEM CAN CAUSE SERIOUS INJURY OR DEATH TO UTILITY WORKERS! Improper connection of generator to a building’s electrical system can allow electrical current from the generator to backfeed into utility lines. This may result in electrocution of utility workers, fire, or explosion. Connections to a building’s electrical system must be made by a qualified electrician and comply with all applicable laws and electrical codes. If connected to a building’s electrical system the generator must meet the power, voltage, and frequency requirements of the equipment in the building. Differences in power, voltage, and frequency requirements may exist and improper connection may lead to equipment damage, fire, and personal injury or death. Familiarity and proper training are required for the safe operation of the machine. Machines operated improperly or by untrained personnel can be dangerous. Read the operating instructions contained in both this manual and the engine manual and familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive instruction from someone familiar with the machine before being allowed to operate it. 2.2.1 NEVER operate the generator when open containers of fuel, paint, or other flammable liquids are near. 2.2.2 NEVER operate the generator, or tools attached to the generator, with wet hands. 2.2.3 NEVER use worn electrical cords. Severe electrical shock and equipment damage may result. 2.2.4 NEVER run the electrical cords under the generator, or over vibrating or hot parts. 2.2.5 NEVER enclose or cover the generator when it is in use or when it is hot. 2.2.6 NEVER overload the generator. The total amperage of the tools and equipment attached to the generator must not exceed the load rating of the generator. DANGER DANGER WARNING

2.2.8 NEVER allow untrained personnel to operate or service the generator. The generator set should be set up by a trained electrician. 2.2.9 NEVER stand on the machine. 2.2.10 DO NOT stand under the machine while it is being hoisted or moved. 2.2.11 DO NOT attach equipment to the machine when it is suspended. 2.2.12 ALWAYS store the equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children. 2.2.13 ALWAYS position and operate the generator on a firm, noncombustible, level surface. 2.2.14 ALWAYS transport the generator in an upright position. 2.2.15 ALWAYS keep the machine far away from structures, buildings, and other equipment during use. 2.2.16 ALWAYS keep the area immediately surrounding and underneath the machine clean, neat, and free of debris and combustible materials. Make sure that the area overhead is clear of debris that could fall onto or into the machine or exhaust compartment. 2.2.17 ALWAYS remove all tools, cords, and other loose items from the generator before starting it. 2.2.18 ALWAYS make certain the machine is well-grounded and securely fastened to a good earthen ground per national and local regulations.

Internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. Failure to follow the warnings and safety guidelines could result in severe injury or death. 2.3.1 NEVER use this generator inside a home or garage, EVEN IF doors and windows are open. Only use OUTSIDE and far away from windows, doors, and vents. Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell. 2.3.2 NEVER use a generator inside an enclosed area such as a tunnel or a trench. 2.3.3 DO NOT smoke while operating the machine. 2.3.4 DO NOT smoke when refueling the engine. 2.3.5 DO NOT refuel a hot or running engine. 2.3.6 DO NOT refuel the engine near an open flame. 2.3.7 DO NOT spill fuel when refueling the engine. 2.3.8 DO NOT run the engine near open flames. 2.3.9 DO NOT start the engine if fuel has spilled or a fuel odor is present. Move the generator away from the spill and wipe the generator dry before starting. 2.3.10 ALWAYS refill the fuel tank in a well-ventilated area. 2.3.11 ALWAYS replace the fuel tank cap after refueling. 2.3.12 ALWAYS check the fuel lines and the fuel tank for leaks and cracks before starting the engine. Do not run the machine if fuel leaks are present or the fuel lines are loose. DANGER

for the equipment to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. If the generator is experiencing problems or is being serviced, attach a “DO NOT START” sign to the control panel to notify other people of its condition. 2.4.1 DO NOT use gasoline or other types of fuels or flammable solvents to clean parts, especially in enclosed areas. Fumes from fuels and solvents can become explosive. 2.4.2 DO NOT attempt to clean or service the machine while it is running. 2.4.3 DO NOT modify the machine without the express written approval of the manufacturer. 2.4.4 DO NOT allow water to accumulate around the base of the machine. If water is present, move the machine and allow the machine to dry before servicing. 2.4.5 DO NOT service the machine if your clothing or skin is wet. 2.4.6 DO NOT allow untrained personnel to service this equipment. Only trained electrical technicians should be allowed to service the electrical components of this equipment. 2.4.7 ALWAYS keep the machine clean and labels legible. Replace all missing and hard-to-read labels. Labels provide important operating instructions and warn of dangers and hazards. 2.4.8 ALWAYS replace the safety devices and guards after repairs and maintenance. 2.4.9 ALWAYS let the engine cool before transporting or servicing it. 2.4.10 ALWAYS keep hands, feet, and loose clothing away from the moving parts on the generator and engine. 2.4.11 ALWAYS turn the engine off before servicing the machine. If the engine has electric start, disconnect the negative terminal on the battery before servicing the machine. 2.4.12 ALWAYS keep the fuel lines in good condition and properly connected. Leaking fuel and fumes are extremely explosive. WARNING

Wacker machines use international pictorial labels where needed. These labels are described below: Label Meaning DANGER! No sparks, flames or burning objects near machine. Shut off the engine before refueling. WARNING! Hot surface! Improper connection of generator to a building’s electrical system can allow electrical current from the generator to backfeed into utility lines. This may result in electrocution of utility workers, fire, or explosion. Connections to a building’s electrical system must be made by a qualified electrician and comply with all applicable laws and electrical codes. Close main circuit breaker. CAUTION! Use only clean, filtered gasoline fuel. Check the fuel level.

Close the choke. Turn the engine switch to the ON position. Pull the rewind starter. Open the choke. Open main circuit breaker. Turn the engine switch to “OFF”. Close the fuel flow valve. Label Meaning

carbon monoxide. This is a poison you cannot see or smell. NEVER use inside a home or garage, EVEN IF doors and windows are open. Only use OUTSIDE and far away from windows, doors, and vents. This equipment does not meet California EVP emission regulations for small off-road engines. A nameplate listing the model number, item number, revision number, and serial number is attached to each unit. Please record the information found on this plate so it will be available should the nameplate become lost or damaged. When ordering parts or requesting service information, you will always be asked to specify the model number, item number, revision number, and serial number of the unit. Label Meaning A MADE IN USA MADE IN USA Model Model Item No. Item No. Rev. Rev. Serial No. Serial No. kg kg V kW Max kW Max lbs lbs Ø P.F. P.F. 164329 164329 hz hz

This generator is designed to operate single-phase, 60 Hz appliances running at 120 VAC. Check the nameplate or label provided on tools and appliances to make sure their power requirements match the power output of the generator. Some appliances and tools require a surge of current when starting. This means that the amount of power needed to initially start the equipment is larger than the power required to keep it running. The generator must be capable of supplying this “surge” current. Other types of appliances require more power than is actually stated on their nameplate. The information in “Approximate Starting Power Requirements” is offered only as a general guideline to help you in determining power requirements for different types of equipment. Check with your nearest Wacker Dealer, or contact the manufacturer or dealer of the tool or appliance, with questions regarding its power requirements. NOTICE: If a tool or appliance does not reach full speed within a few seconds when switched on, turn it off immediately to avoid damage. Approximate Starting Power Requirements • Incandescent lights and appliances such as irons and hot plates, which use a resistive-type heating element, require the same wattage to start and run as is stated on their nameplates. • Fluorescent and mercury lamps require 1.2–2 times their stated wattage to start. • Electrical motors and many types of electrical tools often require a large starting current. The amount of starting current depends on the type of motor and its use. • Most electrical tools require 1.2–3 times their stated wattage for starting. • Loads such as submersible pumps and air compressors require a very large force to start. They need as much as 3–5 times the wattage stated on the nameplate in order to start. If the wattage is not given for a particular tool or appliance, it can be calculated by multiplying its voltage and amperage requirements: Single Phase: VOLTS x AMPS = WATTS Three Phase: VOLTS x AMPS x 1.732 x 0.8 = WATTS

snow, or direct sunlight. Make sure it is positioned on firm, level ground, so it will not slide or shift. Position the engine exhaust away from areas where people may be present. The surrounding area must be free from water and moisture. All components must be protected from excessive moisture. Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use this generator inside a home or garage, EVEN IF doors and windows are open. Only use this generator OUTSIDE and far away from windows, doors, and vents. NEVER install a generator in an enclosed area such as a tunnel or a trench. Using a generator in a tunnel or a trench CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use this generator inside a tunnel or a trench. 3.3 Installing Spark Arrester A spark arrester is available as an accessory for this machine. Install the spark arrester prior to using the machine in areas where spark arresters are required. To install spark arrester: 3.3.1 Position the spark arrester (a) on the engine exhaust pipe (b). 3.3.2 Secure the spark arrester with screw (c) included with spark arrester. DANGER DANGER DANGER

Internal combustion engines, unless modified, run less efficiently at higher altitudes due to the reduction of air pressure. This translates into a lack of power and thus reduction in generator output. Temperature affects both engine and generator performance. As temperature increases, an engine will run less efficiently and more resistance will be found in electrical components. Therefore, as the temperature increases, the output of the generator decreases. Altitude also affects the cooling capacity of air—the higher the altitude the less dense the air is and thus the lower its ability to transfer heat. For every increase in altitude of 500 m (1650 ft.) above 1000 m (3300 ft.), the output of the generator will be reduced by 3%. For every increase of 5° C (9° F) in ambient temperature above 40° C (104° F), the output of the generator will be reduced by 3%. Use the tables shown for altitude and temperature deration factors. It may be necessary to consider both altitude and ambient temperature deration factors to determine true generator output. Ambient Temp. °C (°F) Derate Factor 45 (113) 3 % 0.97 50 (122) 6 % 0.94 55 (131) 9 % 0.91 60 (140) 12 % 0.88 Altitude m (ft.) Derate Factor 1500 (4900) 3 % 0.97 2000 (6600) 6 % 0.94 2500 (8200) 9 % 0.91 3000 (9900) 12 % 0.88 3500 (11500) 15 % 0.85 4000 (13100) 18 % 0.82

A ground connection (a) is located on the generator frame. For proper operating safety, this ground terminal must be connected to a good ground source. This ground connection must comply with National Electrical Code standards, and state and local regulations. 3.6 Operating Heavy Loads Limit operations requiring the maximum rated output of 6600 Watts to 20–30 minutes. For continuous operation, do not exceed the continuous rated output of 6000 Watts. NOTICE: DO NOT exceed the current limit specified on the control panel for any receptacle. a

When a long extension cord is used to connect an appliance or tool to the generator, a voltage loss occurs—the longer the cord, the greater the voltage loss. This results in less voltage being supplied to the appliance or tool and increases the amount of current draw or reduces performance. A heavier cord with a larger wire size will reduce the voltage loss. Damaged extension cords can cause electrical shock, resulting in serious injury or death. DO NOT use worn, bare, or frayed cords. Replace damaged cords immediately. Use the chart below as a guide for selecting proper cable size. Use only extension cords rated for outdoor use and equipped with a third-wire ground. NOTICE: Operating equipment at low voltage can cause it to overheat. Current Load in Watts Maximum Cable Length in Feet (Amps) 120V 240V #10 #12 #14 #16 2.5 300 600 1000. 600 375 250 5 600 1200 500 300 200 125 7.5 900 1800 350 200 125 100 10 1200 2400 250 150 100 - 15 1800 3600 150 100 65 - 20 2400 4800 125 75 50 - WARNING

b Auto idle switch g GFI test button c Twist-lock receptacle—125/250V h GFI reset button d Main circuit breaker i Twist-lock receptacle—125V e Voltage Selector Switch (VSS) - ---

See Graphic: wc_gr003960 Each of the 125V, 20 Amp receptacles (f) is equipped with a ground fault circuit interrupt (GFI). The GFI shuts off power to the receptacle when a ground fault occurs to a piece of equipment attached to the generator. The GFI should be tested for proper operation every time the generator is used. To test the GFI: 3.9.1 Disconnect all equipment from the generator. 3.9.2 Start the generator. 3.9.3 Push the TEST button (g) on the receptacle in. Pushing the TEST button in shuts off power to the receptacle and causes the RESET button (h) to pop out. If the RESET button does not pop out, the GFI is not working. Do not operate the generator until the problem can be corrected. 3.9.4 Push the RESET button in to restore power to the receptacle. If the RESET button pops out during operation, stop the generator and check the equipment attached to the generator for defects. 3.10 Main Circuit Breaker See Graphic: wc_gr003960 The generator is protected by a two-pole, 15-Amp per pole, main circuit breaker (d) located on the control panel. The main circuit breaker protects the generator from severe overloads or short circuits. If the main circuit breaker opens, turn the engine off immediately and determine the cause before restarting. Check the appliances and tools attached to the generator for defects and make sure their power requirements do not exceed the power rating of the generator or the current limit of the receptacles.

The voltage selector switch (VSS) (e) switches the generator output between the single-voltage mode (120V) and the dual-voltage (120/ 240V) mode. In single-voltage mode, the full rated power of the generator is shared between the two 125V GFI duplex receptacles and the 125V twist-lock receptacle. In dual-voltage mode, generator power is shared between the 125/ 250V twist-lock receptacle, the 125V GFI duplex receptacles, and the 125V twist-lock receptacle. To achieve full power, use only the 125/ 250V twist-lock receptacle. Note: Only use the 125/250V twist-lock receptacle (j) when the VSS is in the 120V/240V position. NOTICE: NEVER change the position of the VSS when the main breaker is in the ON position. This can cause arcing and can damage the generator. Turn all tools and appliances off and place the main circuit breaker (d) in the OFF position before changing the position of the voltage selector switch. 3.12 Engine Auto Idle See Graphic: wc_gr003960 The auto idle switch (b) automatically reduces engine speed after all appliances or tools attached to the generator have been turned off. The engine automatically returns to full speed when a tool or appliance is turned back on. To turn the auto idle feature on, push the auto idle switch to “AUTO”. The AUTO setting is recommended while the generator is running to minimize fuel consumption. To avoid extended engine warm-up periods, keep switch set to “OFF” when starting the engine and until the engine reaches operating temperature.

at the beginning of this manual 3.13.2 Inspect the generator for any signs of damage which may affect operation or pose a safety hazard. 3.13.3 Check: • oil level in engine • fuel level • condition of air cleaner • tightness of external fasteners • condition of fuel lines. Note: The engine is equipped with an oil alert system. If the oil level in the engine drops too low, the engine will not start. 3.13.4 Fill the fuel tank with fresh, regular, unleaded grade gasoline. DO NOT use an oil/gas mixture. The use of gasohol or any fuel containing more than 10% ethanol is not recommended. Consult the engine owner's manual for complete fuel specifications.

operating instructions in this manual. 3.14.1 Disconnect all loads from the generator and place the main breaker in the "OFF" position (a2). 3.14.2 Set the Auto Idle Switch (c) to "OFF". 3.14.3 Open the fuel valve (d1). Note: If the engine is cold, move the choke lever to the closed position (e2). If the engine is hot, set the choke to the open position (e1). 3.14.4 Turn the engine switch to "ON" (b1). 3.14.5 Pull the starter rope (f). Note: If the oil level in the engine is low, the engine will not start. If this happens, check the oil level and add oil as needed. 3.14.6 As the engine warms up, move the choke lever to the OPEN position (e1). 3.14.7 Allow the engine to warm up for a few minutes before placing the main breaker in the "ON" position (a1) and attaching loads. IDLE OFF AUTO MAIN BREAKER a2 a1 b2 b1 c

generator. 3.15.2 Place main circuit breaker in the "OFF" position (a2). 3.15.3 Turn the engine switch to "OFF" (b2). 3.15.4 Close fuel valve (d2). Note: To stop the engine quickly in an emergency, turn the engine switch to "OFF" (b2).

the engine manufacturer’s Operator’s Manual for additional information on engine maintenance. 4.2 Periodic Maintenance Schedule Daily before starting After first 20 hrs. Every 50 hrs. Every 100 hrs. Every 300 hrs. Check the fuel level. „ Check the engine oil level. „ Inspect the air filter. Replace as needed. „ Check external hardware. „ Check condition of the fuel line. Replace when necessary. „ Clean the air cleaner element.* „ Inspect the shockmounts for damage. „ Change the engine oil.* „ „ Clean the sediment cup or fuel strainer. „ Check and clean the spark plug. „ Check and adjust the valve clearance. „ Clean the fuel tank.* „ *Service more frequently in dusty conditions.

4.3.2 Remove the oil filler plug (a) and the drain plug (b) to drain the oil. Note: In the interests of environmental protection, place a plastic sheet and a container under the machine to collect any liquid that drains off. Dispose of this liquid in accordance with environmental protection legislation. 4.3.3 Install the drain plug. 4.3.4 Fill the engine crankcase with the recommended oil up to the level of the plug opening (c). See Technical Data for oil quantity and type. 4.3.5 Install the oil filler plug.

Service the air cleaner frequently to prevent carburetor malfunction. NOTICE: NEVER run the engine without the air cleaner. Severe engine damage will occur. NEVER use gasoline or other types of low flash-point solvents for cleaning the air cleaner. A fire or explosion could result. To service: 4.4.1 Remove the air cleaner cover (a). Inspect the element (b) for holes or tears. Replace the element if it is damaged. 4.4.2 Wash the foam element (b) in a solution of mild detergent and warm water. Rinse it thoroughly in clean water. Allow the element to dry thoroughly. Soak the element in clean engine oil and squeeze out excess oil. WARNING wc_gr002815

Refer to the engine owner’s manual. The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Do not touch the muffler while it is hot. Note: Refer to the Technical Data for the recommended spark plug type and the electrode gap setting. 4.5.1 Remove the spark plug and inspect it. 4.5.2 Replace the spark plug if the insulator is cracked or chipped. 4.5.3 Clean the spark plug electrodes with a wire brush. 4.5.4 Set the electrode gap (a). 4.5.5 Tighten the spark plug securely. NOTICE: A loose spark plug can become very hot and may cause engine damage. WARNING

4.6.1 Turn the fuel valve off. 4.6.2 Remove the sediment cup (a) and the O-ring (b). 4.6.3 Wash both thoroughly in a nonflammable solvent. Dry and reinstall them. 4.6.4 Turn the fuel valve on and check for leaks. wc_gr000029 b a

4.7.1 Close the fuel valve and remove and empty the sediment cup or fuel strainer. 4.7.2 Disconnect the fuel line from the carburetor. Place open end of fuel line into a suitable container and open fuel valve to drain fuel from tank. Gasoline is extremely flammable. Drain the fuel tank in a well- ventilated area. DO NOT drain the fuel tank in an area with flames or sparks. 4.7.3 Loosen the drain screw on the carburetor and drain any remaining fuel from the carburetor. 4.7.4 Change the engine oil. 4.7.5 Remove the spark plug and pour approximately 30 ml (1 ounce) of clean engine oil into the cylinder. Crank the engine a few turns to distribute the oil to the inside of the cylinder walls. 4.7.6 Pull the starter rope slowly until resistance is felt and leave the handle in this position. This ensures that the intake and exhaust valves are closed. 4.7.7 Store the generator in a clean, dry area. WARNING

indoors, to avoid burns or fire hazards. When transporting the generator: 4.8.1 Turn the engine fuel valve to the OFF position. 4.8.2 Position the generator level to prevent fuel from spilling. 4.8.3 Secure the generator by tying it down with a suitable rope. When transporting the machine by hand, be sure to employ manpower commensurate with the weight of the machine. To avoid back injury when lifting the machine, bend the knees to pick it up rather than bending your back only. WARNING WARNING

Reason / Remedy If engine doesn't start, check that: • Engine switch is on "Start". • Fuel valves under fuel tank and on engine are open. • Fuel tank has fuel. • Choke lever is in correct position. Choke should be closed when starting a cold engine. • All loads are disconnected from generator. • Spark plug is in good condition. • Spark plug cap is tight. • Engine oil level is adequate. If engine starts but there is no power at receptacles, check that: • Circuit breaker is closed. • Connector from generator to control panel is tight.

AC voltages available Volts phase 120/240 1 Frequency Hz 60 Power factor cos ø 1.0 AC receptacles: 125V GFI duplex (2) 125/250V twist lock 125V twist lock Amp Amp Amp 20 30 30 Main circuit breaker (two pole) Amp 15 per pole L x W x H mm (in.) 710 x 550 x 515 (28.0 x 21.6 x 20.3) Weight (dry) kg (lbs.) 80 (176.4)

Operating power (max.) kW (Hp) 9.7 (13) Spark plug BPR6ES (NKG) Electrode gap mm (in.) 0.7–0.8 (0.028–0.031) Operating speed (max.) rpm 3600 Air cleaner type Oil-wetted foam Engine lubrication oil grade SAE 10W30 service class SF or SG Engine oil capacity l (qts.) 1.1 (1.2) Fuel type Regular unleaded gasoline Fuel tank capacity l (gal.) 21 (5.5) Fuel consumption l (qts.)/hr. 3.9 (4.1) Running time - continuous load hrs. 5.4

Technical Data GV 6600A wc_td000208gb.fm 36 5.3 Electrical Schematic A B 15 16 17 24 18 6 6 5 3 14 1 9 8 19 20 10 11 21 13 12 4 2 22 23 C

13 Spark plug 2 Secondary winding 14 Slip ring 3 Rotor winding 15 Auto idle unit 4 Automatic voltage regulator 16 Voltage selector switch 5 Main circuit breaker 17 Twist lock receptacle—125/250V 6 GFI duplex receptacle—125V 18 Auto idle switch 7 --- 19 Idle solenoid 8 Engine ON-OFF switch 20 Capacitor 9 Oil alert module 21 Fuel stop solenoid 10 Oil level switch 22 Auxiliary winding 11 Ignition coil 23 DC rectifier 12 Ground terminal 24 Twist lock receptacle—125V

Wacker Corporation · P.O. Box 9007 · Menomonee Falls, WI 53052-9007 · Tel. : (262) 255-0500 · Fax: (262) 255-0550 · Tel. : (800) 770-0957 Wacker Asia Pacific Operations · Skyline Tower, Suite 2303, 23/F · 39 Wang Kwong Road, Kowloon Bay, Hong Kong · Tel. +852 2406 60 32 · Fax: +852 2406 60 21