SAVEO SAVEO-SCAN-PKT-RCCD-BT Manual 

Please switch on and charge your scanner for 3~4 hours before frst use. Exit window Scan/Power On Button Power Saving button: Press the button for 2~3 seconds to enter power saving mode Mini USB port with protective cover Charge the pocket scanner with mini USB cable. LED Indicator Please note: LED indicator will remain red until scanner has been paired with a device. (For iOS Devices ONLY) Button to raise and lower ON-Screen Keyboard Operating Elements SAVEO-SCAN-PKT-RCCD-BT Connecting via Bluetooth Enable Bluetooth on your device Go to your phone’s homescreen and fnd “Settings”, then “Bluetooth” and turn Bluetooth on. Scan Profle barcodes A1 A2 Demo %H%I%D Demo %B%R%C After you scan the Bluetooth profle barcodes below, your scanner will become visible to Bluetooth enabled devices within range. HID Profle Please note: The scanner should only be paired with one device at a time. Before you pair your scanner to another device, please frst unpair it from the device in use. Otherwise it will appear on your list of “Available Devices” but will not connect. In this case, please refer to “Unpairing your device” in this guide. Search for devices Your phone will automatically search for devices, Saveo Scan will appear as an external keyboard with a unique identifer number (R-xxxxxx). Select R-xxxxxx to connect Please note: devices only need to be paired once. When they are within Bluetooth range they will automatically attempt to connect to each other. If you wish to pair to another device it is recommended you frst unpair this device. You are now connected. Start scanning. Select scanner from “Available Devices” and wait for pairing process to complete. Devices are now paired Once “Connected” is displayed, your device is paired to the scanner. Your scanner is now ready to use.

for 3-4 seconds to unpair from device. Using the scanner to unpair Unpairing on your phone Unpairing your device Before connecting the scanner to another device it is recom- mended you frst unpair from the current device. This can be done on the scanner or through the system menu on your smartphone/tablet. To unpair using the scanner, press and hold the left button (as illustrated) for 3-4 seconds. You will hear a notifca- tion sound and the LED will turn red to indicate it is not paired to any device. Go to the Bluetooth menu on your phone and select the option menu for scanner from list of paired devices. Choose “Forget this Device”/”Unpair” 5 There are two operating modes on the scanner, Data transmis- sion mode and Data Storage Mode. Scan the appropriate barcodes when switching between these two modes. Please note: Switching between modes will wipe the scanner’s internal memory. Operating Modes Data Transmission Mode (Default) Our Default setting is Data Transmission mode. In this mode data will be sent to smartphone/tablet directly. To enter Data Transmission Mode please scan the follwing barcodes. Demo %E%R%A Demo %M%A%F Enter Data Transmission Mode Green/Orange LED fashes followed by 3 beeps. Demo %M%A%N Data Storage Mode In this mode, data will be saved directly to scanner’s memory. Scan Transmit Memory Data to receive data stored on scanner’s internal memory. Enter Data Storage Mode Green/Orange LED fashes followed by 3 beeps. Demo %E%R%A To enter Data Storage Mode please scan the follwing barcodes. Demo %E%R%A Clean Memory Data Green/Orange LED fashes followed by 3 beeps. Demo %R%E%C Transmit Memory Data Green/Orange LED fashes followed by 3 beeps. Transmit Memory Data Scan the following barcode to receive data stored in the scanner’s internal memory.. After data is transmitted to your device it remains on the scanner’s internal memory. Scan the following barcode to clear the memory if you do not wish to send this data again. When the battery power is too low, the Orange LED will fash and beep once. Scanner should be charged immediately. If scanner shuts down it is recommended to charge it fully then power it back on. Under power-saving mode, there will not be an LED indication when charging. Orange LED ON Full charged Orange LED (Flashing) Charging / Low battery Red LED ON Ofine / Out of Range Green LED ON Good read Orange LED ON Good read (Batch mode) LED Indicator Information LED Indicator Demo Current Battery Level Scan to receive the current battery level Scan the following barcode to send battery level information to your device. The format is outlined in the table below. %^4^% 80% - 100% %^3^% 55% - 80% %^2^% 30% - 55% %^1^% 10% - 30% %^0^% under 10% Battery Level Status

scanner to sleep after 1 minutes inactivity. To wake up the scanner press the trigger. Demo %P%D%T00 Disable Scan to disable power saving mode Demo %P%D%T01 Below are the barcodes to disable/enable power saving mode. Power Saving Mode 1 Minute Enter Power Saving Mode after 1 minutes inactivity 5 Minute Enter Power Saving Mode after 5 minutes inactivity 15 Minute Enter Power Saving Mode after 15 minutes inactivity 30 Minute Enter Power Saving Mode after 30 minutes inactivity Reset to Defaults Reset Confguration to Defaults (scan from A1to A6) HID Profle Transmission Speed Transmission speed is dependent on your device. In order not to lose data please choose the correct speed. Mid Speed is the default. Mid Speed Transmission (Default) High Speed Transmission Low Speed Transmission Demo %B%T%H Demo Demo %B%T%L Sound Settings Scan the barcodes below in order (A1 - A2, B1 - B2) to select whether or not the decoder issues a beep signal after a good decode. If selecting Do Not Beep after Good Decode, beeper signals are issued during parameter menu scanning and to indicate errors. Beep after good decode Do not beep after good decode A1 A2 A3 A4 A5 A6 Demo !" #$%& Demo !" #$%& Demo !" # Demo !" # Demo !" #$%& Demo %D%F%T A1 A2 A3 Demo +%-$.2 Demo +%-$.4 A1 A2 A3 Demo +%-$.2 Demo +%-$.4