AER COMPACT 60 2 Operating Manual

Thank you for choosing the Compact 602. You have chosen a profes- sional, powerful and compact amplifier system for acoustic instru- ments in superb quality with AER‘s typical authentic, transparent and self-asserting sound performance. Two channels make it possible to operate a microphone and an instrument independently of each other. The dynamically controlled power amplifier and the broad- sprectrum loudspeaker system guarantee distortion-free repro- duction even at high volumes. We wish you hours of happy playing with your Compact 602! Acoustic Solutions Compact 602 Operating Manual Contents: 1. Introduction 2. Safety Precautions 3. Controls and Connections 4. Operation Summary 5. Technical Data 6. Block Diagram 7. Effects Table 8. Manufacturer‘s Declaration

The following guidelines shall help minimize the risk of injury through fire or electric shock. 1. Carefully read these safety notes before you use the device! 2. Keep these safety notes in a safe place. 3. Pay attention to all warnings, instructions and additional texts on the unit. 4. Do not install or use your amp in close proximity to water or if you are wet yourself. 5. Use your amp in a safe place where nobody can step on cables or trip over and damage them. 6. Pay attention to an unhindered air circulation around the amp, ne- ver obstruct the air vents or grilles. 7. Always pull the mains plug before cleaning your amp. Use only a dry cloth for cleaning. Avoid the use of detergents and do not let any liquids seep into the unit. channel 1 input 6.3 mm stereo jack socket high/low Input sensitivity selector switch pressed = lower sensitivity clip This indicator lights up when overload is imminent in the respective channel. gain Input level control colour This switch activates the midrange contour filter. Boosts presence and slightly cuts midrange frequencies. bass Bass control middle Midrange control treble Treble control input CCompact 602 input clip clip select power line mic high low colour channel 1 channel 2 gain gain bass effect eff. pan return master treble bass middle treble channel 2 input XLR/6.3 mm jack plug combi socket line/mic Signal source selector switch. line: For instruments (pickups), only via jack plug. mic: For microphones with a jack or an XLR connector. clip This indicator lights up when overload is imminent in the respective channel. gain Input level control bass Bass control treble Treble control eff. pan panorama control to distribute the effects between the channels. left: internal effect on channel 1 & external effect on channel 2 mid: internal & external effect on channel 1 and channel 2 right: internal effect on channel 2 & external effect on channel 1 select push button for selection of four effects, indicated by the LEDs between return and master. return level control for the internal effects power This LED indicates that your amplifier is ready to use master Adjusts the overall volume level 3. Controls and Connections Front panel top (from left to right):   8. Use only the right fuses with the same current rating and trigger characteristic as replacements. Never mend fuses! Pull the mains plug before replacing a fuse. Should a fuse blow again after a short while, the device needs to be checked.   9. Never install your amp close to devices with strong elec­ tromagnetic fields such as large mains transformers, revolving machines, neon illumination etc. Do not lay signal cables parallel to power current cables. 10. There are no user-servicable components inside the unit. To avo- id the risk of an electric shock, the unit must not be opened. All maintenance, adjustment and repair works should be carried out by qualified staff only. Any unauthorized tampering will void the 2-year warranty. 11. In keeping with the EMV regulations screened cables with cor- rectly fitted connectors must be used for all signal connections. 12. Always use an earthed power supply with the correct mains volta- ge. If you are in doubt about the power outlet‘s ground, have it checked by a qualified technician. 13. Cable up your amp only when it is powered off.

6.3 mm stereo jack socket. Never use mono jack plugs, otherwise the amp could be damaged! tuner Output to an external tuner. 6.3 mm mono jack socket. line out preamplifier output after the master control. 6.3 mm mono jack socket. DI-out Balanced preamp output, pre master, post EQ, with return and effects. XLR socket send Output to the input of an external effects unit. 6.3 mm mono jack socket. return Input for the output signals of an external effects processor. 6.3 mm mono jack socket. footswitch connection to a double footswitch to switch internal and external effect on and off. (Tip = internal Effect, Ring = external Effect on/off). 6.3 mm stereo jack socket. power on Combined power switch with fuse holder and IEC mains socket Back panel (from left to right): Caution: Risk of electric shock. Do not open! No user serviceable parts inside. Refer servicing to qualifed personnel. Made in Germany by AER. Compact 602 twin channel acoustic amplifier

• Cabling and startup Check if your local mains voltage (e.g. 120 V in the USA, 230 V in Euro­ pe) complies with the required operating voltage for your amplifier. The proper mains voltage is printed on the rating plate on the rear panel of the unit, e.g. AC 230V (AC means alternating current). Please take care that the master, return and all gain controls are set to zero (left stop) and all other controls to their center positions. The pushbuttons should be switched off (not pressed). Then make all the necessary cable connections (mains, instrument etc.). Now you may turn on your amplifier with the power on switch loca- ted on the rear. The green power control LED will indicate operational readiness. • Level adjustment Using the gain controls, high/low and line/mic switches you can ad- apt the amplifier to your signal sources (guitar pickups, microphone etc.) to achieve the best possible signal-to-noise ratio (SNR). First adjust the line/mic switch according to your signal source: mic is suitable for microphones, line for pickups and other signal sources. Turn the gain control clockwise until the red clip indicator flashes momentarily when playing with a strong attack. Now lower the gain control (and also the instrument‘s volume control) again slightly to get some headroom for an undistorted reproduction. The clip control LED should now only rarely flash. In case you find the level setting difficult because the input signal is too strong, press the high/low switch as well. If the input signal is too weak, the gain control must be increased accordingly. With signal sources with a sufficient input si- gnal strength the gain control should be adjusted between the ‘ 9:00 and 11:00 o‘clock‘ position. Finally set the desired overall volume level with the master control. • Equalization The three-band equalizer with individual bass, middle and treble control of your Compact 602 has been designed in such a way that it both complies with the special requirements of acoustic instruments and also with the more general demands of other sources. The colour switch activates a midrange contour filter which is especially useful for picking techniques. One more note: Adjusting the EQ controls can also affect the level setting. Whenever you see the clip indicator flashing frequently, you should slighty correct your gain setting (see ‚Level adjustment‘). • Effects The Compact 602 has a built-in (internal) digital effect processor. The return control determines the intensity of the internal effects (left stop = no effect). Furthermore an additional effects unit (external ef- fect) may be connected. For this purpose please use the send and return sockets located on the back of the amplifier (send goes to In- put, return is connected to the output of the external effects device). The intensity is then adjusted at the external effects unit. The external effects loop works in ‚parallel‘ mode, i.e. the effect signal is blended with the original signal. A standard double footswitch can be connected to the footswitch socket on the rear of the amp with a stereo cable. This switch can be used to turn the internal and external effects on and off. We wish you hours of happy playing with your Compact 602!

Inputs Input (channel 1) Stereo jack ¼” (6.35 mm) High impedance, unbalanced jack input for instruments (pick-ups) and line-level sources. high/low switch: –10 dB attenuator Impedance: 2.2 Meg Input (channel 2) Combo socket, XLR jack ¼” (6.35 mm) line mode: High impedance, unbalanced jack input for instruments (pick-ups) and line-level sources. Sensitivity: 38 mV Impedance: 1 Meg mic mode: XLR (balanced), stereo jack (balanced), or mono jack (unbalanced) input. Voice Filter 24 V-Phantom-Power through 6.8 kohms to XLR socket Clip indicator: Headroom 6 dB Return Return from external parallel effect loop Sensitivity: 430 mV Clip Headroom: 15 dB Attack Time: 4 ms Outputs (note 3) Phones Headphones output. When connected, internal speakers are muted. Stereo jack, ¼” (6.35 mm) Output power: 100 mW Caution: For stereo headphones with stereo jack plug only. Do not connect mono plugs. Tuner Tuner output. Mono jack, ¼” (6.35 mm) Output voltage: 310 mV Line out Line output after tone controls, with return and effects. Mono jack, ¼” (6.35 mm). Output Voltage: 1.3 V DI-out Line output after tone controls, with return and effects. Mono jack, ¼” (6.35 mm). Output Voltage: 1.3 V Send Send for parallel effect loop Mono jack, ¼” (6.35 mm) Output voltage: 1.3 V Tone controls Bass channel 1: ± 8 dB at 100 Hz channel 2: ± 8 dB at 100 Hz Middle channel 1: ± 6 dB at 800 Hz Treble channel 1: ± 8 dB at 10 kHz channel 2: ± 11 dB at 10 kHz Effects Internal effect digital effect processor with 4 factory presets 1 – warm hall 2 – bright hall 3 – chorus with reverb 4 – flanger External effect Parallel effect loop (see send and return) Power Power amp 60 W at 4 ohms, discrete bipolar transistor design Analog signal Subsonic filter, low distortion RMS limiter processing Speaker system 8” (200 mm) twin cone speaker Mains power AC 230 V, 50-60 Hz, max. 120 W (other mains voltage available) Mains fuse slow 1 A for 230-240 V slow 2 A for 115 V slow 2 A for 100 V General Cabinet 15 mm (0.6”) finnish birch plywood Finish Waterbased acrylic, choco spatter finish Dimensions 265 mm (10.4 “) high 330 mm (13 “) wide 235 mm (9.25 “) deep Weight 7,55 kg (16.65 lbs) Notes: Input levels refer to 50 Watts output. Output levels refer to 50 mV input at channel 1. Specifications and appearance subject to change without notice.

LINE MIC MIC LINE Option GAIN COLOUR MIDDLE OFF/ON SUBSONIC LIMITER POWER AMP FX DUAL CONE SPEAKER TUNER TREBLE BASS BASS TREBLE CLIP Clip detect CLIP Clip detect SEND EFF. RETURN MASTER SELECT LINE F/S RETURN PHONES DI GAIN PREAMP VOICE PREAMP EFFECT PAN T R +15V PAD CH 1 +24V T R CH 2 1 2 3 1 2 3 6. Block Diagram

The disposal of electronic equipment in household waste is not per- mitted. AER GmbH waste electrical and electronic equipment is not to be taken to public collection points for disposal. AER GmbH remains solely responsible for the disposal of AER GmbH waste electrical and electronic equipment labelled with a dustbin. To dispose of AER GmbH waste electrical and electronic equipment that is labelled with a dustbin symbol, please contact us; we will ensure correct and cost-neutral disposal. In the case of AER GmbH waste electrical and electronic equipment that is not labelled with a dustbin, the owner is responsible for cor- rect disposal in accordance with the law. However, we are also happy to help in this case and we can present you with the options of where to dispose of these electrical goods. The telephone number of AER GmbH: +49 (0)2361 891789 Here, we will provide you with qualified information on the disposal of AER GmbH waste electrical and electronic equipment. Declaration The EU directive on the disposal of waste electrical and electronic equipment (WEEE, 2002/96/EC) has been changed to the electrical and electronic equipment act. All AER electrical equipment affected by WEEE has been labelled with the symbol of a crossed out dustbin since 13.08.2005. This symbol indicates that the disposal of the equipment is not per- mitted with household waste. It has been circulated in this form since 13.08.2005. In the German registration department EAR, AER GmbH has been registered under WEEE registration number DE26301529. www.aer-amps.com 20090701 7. Effects Table Nummer Bezeichnung Art LED Description Type 01 warm hall reverb 02 bright hall reverb 03 chorus with reverb chorus/reverb 04 flanging flanger European Union, Norway, Iceland and Lichtenstein The disposal of electronic equipment in household waste is not permitted. All AER electrical equipment affected by WEEE has been labelled with the symbol of a crossed out dustbin since 13.08.2005. This is also ap- plicable for Norway, Iceland and Liechtenstein. This symbol indicates that the disposal of the equipment is not per- mitted with household waste. It has been circulated in this form since 13.08.2005. The European directives of WEEE are anchored in different respecti- ve national laws in all European states. As such, we are unfortunately unable to provide you with one standard disposal solution. The distributor or importer for the respective state is responsible for the observance of the laws of that state and must ensure the disposal of the waste electrical and electronic equipment in accordance with national regulations. Other Countries For correct disposal of the electrical goods, please ask the local dealer or the appropriate authority.