Ambirad Vision VS Assembly, Installation & Servicing

MANUAL FOR AMBIRAD VISION® VS RANGE OF RADIANT TUBE HEATERS INDEX Section Introduction and Document Index Installation Requirements -------------------------------------------------1 Assembly Instructions------------------------------------------------------2 Commissioning Instructions----------------------------------------------3 Servicing Instructions ------------------------------------------------------4 Spare Parts-------------------------------------------------------------------5 Fault Finding Guide --------------------------------------------------------6 Replacing Parts -------------------------------------------------------------7 User and Operating Instructions ----------------------------------------8 WARNINGS AmbiRad equipment must be installed and maintained in accordance with the relevant provisions of the Gas Safety (Installations and Use) Regulations 1998 for gas fired products. Due account should also be taken of any obligations arising from the Health and Safety at Works Act 1974 or relevant codes of practice. In addition the installation must be carried out in accordance with the current IEE wiring regulations (BS 7671), BS 6896:2005 (Industrial & Commercial) and any other relevant British Standards and Codes of Practice by a qualified installer. All external wiring MUST comply with the current IEE wiring regulations.

1.1 Health & Safety 1.2 Model Definitions 1.3 Heater Suspension 1.4 Wall Mounting 1.5 Herringbone Systems 1.6 Clearance to Combustibles 1.7 Gas Connection & Supply Details 1.8 Electrical Connections 1.9 Ventilation Requirements 1.9.1 Unflued Radiant Heater Mechanical Ventilation Natural Ventilation 1.9.2 Flued Radiant Heater Mechanical Ventilation Natural Ventilation 1.10 Flue & Combustion Air Inlet Options 1.11 Technical Details 2 Assembly Instructions 2.1 Tools Required 2.2 Assembly Notes 2.2.1 Tubes 2.2.2 Turbulators 2.2.3 Brackets 2.2.4 U Bends 2.2.5 Couplers 2.2.6 Reflectors 2.2.7 End Caps 2.2.8 Burner Assembly 2.2.9 Fan Assembly 2.2.10 DL Condensate Box Assembly 2.2.11 HB Damper Assembly 2.2.12 HB Manifold Assembly 2.2.13 Detailed Assembly Drawings 3 Commissioning Instructions 3.1 Tools Required 3.2 Balancing the Herringbone System 3.3 Balancing a DL System 3.4 Commissioning Chart for VS Unitary Heaters 4 Servicing Instructions 4.1 Tools Required 4.2 Burner Description 4.3 Burner Removal 4.4 Burner Gas Injector Servicing 4.5 Burner Head and Electrode Servicing 4.6 Combustion Fan Assembly Induced Burner 4.7 Combustion Fan Assembly Forced Burner 4.8 Radiant Tube Servicing 4.9 Reflector Servicing 4.10 Inspection of Flue 4.11 Re-commissioning after Service 5 Spare Parts 6 Fault Finding Guide 7 Replacing Parts 7.1 Burner Controller Replacement 7.2 Air Pressure Switch Replacement 7.3 Gas Valve Replacement 8 User and Operating Instructions 8.1 To Start Heater 8.2 To Switch Off Heater 8.3 Routine Maintenance Between Service Intervals 8.4 Frequency of Servicing at height regulations are adhered to at the mounting heights specified. PLEASE READ this document prior to installation to familiarise yourself with the components and tools you require at the various stages of assembly. All Dimensions shown are in mm unless otherwise stated. The manufacturer reserves the right to alter specifications without prior notice. Welcome to the new range of high efficiency AmbiRad Vision radiant tube heaters. Local regulations may vary in the country of use and it is the installers responsibility to ensure that such regulations are satisfied All installation, assembly, commissioning and service procedures must be carried out by suitable qualified competent persons to the statutory regulations in the country of use. When assembling, installing, commissioning and servicing is undertaken on radiant tube heaters specified in these instructions, due care and attention is required to ensure that working 1. Installation Requirements. Isolate any electrical supply to the heater and controller before proceeding. obligations arising from the Health and Safety at Works Act 1974 or relevant codes of practice. In addition the installation must be carried out in accordance with the current IEE wiring regulations (BS 7671), BS 6896:2005 (Industrial & Commercial) and any other relevant British Standards and Codes of Practice by a qualified installer. Isolate all electrical supplies to the heater & controller before proceeding. 1.1 Health and Safety AmbiRad heaters must be installed in accordance with the relevant provisions of the Gas Safety (Installations and Use) Regulations 1998. Due account should also be taken of any

safety boots and leather faced gloves when handling sharp or heavy items. The use of protective eye wear is also recommended. 1.2 Model Definitions VSUT = AmbiRad Vision U Tube heater with painted induced burner, stainless steel reflector & end caps. VSUH = AmbiRad Vision U Tube heater in Herringbone manifold configurations with painted induced burner, stainless steel reflector & end caps. VSLI = AmbiRad Vision Single Linear heater with painted induced burner, stainless steel reflector & end caps. VSLF = AmbiRad Vision Single Linear heater with painted Forced burner, stainless steel reflector & end caps. (Nat Gas ONLY) VSLH = AmbiRad Vision Linear heater in Herringbone manifold configurations with painted induced burner, stainless steel reflector & end caps. VSDL = AmbiRad Vision Double Linear heater with painted induced burner, stainless steel reflector & end caps. VSAUT, VSAUH, VSALI, VSALF, VSALH & VSADL = As above except: aluminised reflector with no end caps. 1.3 Heater Suspension See fig 3b. Attachment to the heater support lugs should be made by a ‘speed link’, D shackle or in the case of drop rods, a closed formed hook. The hanging attachments to overhead steelwork etc. must be purpose made to good sound engineering practice or of a proprietary type fixing. They must be adequately fixed and designed to carry the whole weight of the heater. In the event of suitable roof steelwork being unavailable, additional steelwork should be fitted to enable vertical hangers to be used for suspending the heaters. These methods are illustrated in Figure 3.b. If there are any doubts as to the strength or suitability of roof steelwork to which heaters are to be suspended, please refer to a Consultant, Architect or owner of the building. The recommended mounting heights for AmbiRad heaters are given in the table above. 1.4 Wall Mounting These radiant tube heaters can be wall mounted using the appropriate bracket (AmbiRad part no WMB-13-22-38). When using the wall mounting brackets the heater must be inclined at an angle between 30° and 45°. Table 1 Angle Mounting Figure 3.a. Angle Mounting using the Wall mounting bracket U Tube Linear Heater Size Required angle Chain length Eyebolt position Chain length Eyebolt position 15 - 30 30-35° 10 links 2 7 links 1 45° 13 links 2 9 links 1 35 - 50 30-35° 12 links 3 8 links 1 45° 16 links 3 10 links 1 Model Horizontal Inclined / wall mounted 15 4.0 - 5.0m 3.5 - 4.5m 20 4.5 - 7.0m 3.5 - 5.0m 25 5.0 - 8.0m 4.0 - 5.0m 30 5.5 - 9.0m 4.0 - 6.0m 35 6.0 - 10.0m 4.5 - 6.5m 40 6.5 - 11.0m 5.0 - 7.0m 45 7.0 - 12.0m 5.5 - 8.0m 50 7.5 - 13.0m 6.0 - 9.0m Recommended Mounting Height (m) 1. 2. 3. E

Where chain supports have an angle of inclination greater than 15° an equal and opposite support is recommended. Vertical suspension chain ideal. Where supports are inclined, maximum recommended angle of inclination is 15°. Shackle method of attachment. Pin must be tightened by pliers. Drop rod with formed hook. note. hook or eyebolt must be closed tight. 15° max. ON U TUBE VARIANTS THE HEATER SHOULD SLOPE DOWNWARDS TOWARDS THE RETURN BEND AND ON LINEAR VARIANTS SHOULD SLOPE DOWNWARDS TOWARDS BURNER BY APPROX. 10mm FOR BOTH HORIZONTAL AND WALL MOUNTED INSTALLATIONS. Typical Speedlink attachment. * These angles to be equal and not more than 45°. Vertical or inclined suspension on this plane is acceptable. * * U TUBE SUSPENSION * * ** Alternative suspension for Linear via single chain. SINGLE LINEAR SUSPENSION **

The manifold system should be arranged to fall slightly in the direction of the vacuum fan. This ensures that any condensation formed in the manifold on cold start and cool down is not trapped or allowed to drain back into the heater unit. This allows condensate to flow towards the condensate trap located at the vacuum fan end of the manifold system. (See figure 4a below for condensate trap arrangement). The manifold should be supported by chain, stainless steel flexible wire, or other flexible means from the roof structure to allow movement caused by thermal expansion. For 100mm diameter manifold the maximum distance between supports is 2.4m and 3.0m for 150mm diameter. Flexible couplers (supplied by AmbiRad) must be inserted within the manifold system to allow linear expansion to take place and prevent stress and strain on the system. The exhaust flue should be adequately supported from the building structure and installed in accordance with the British Standard Code of Practice BS 5440: Part 1:2000 – Installation and maintenance of flues and ventilation for gas appliances of rated input not exceeding 70kW net (1st, 2nd and 3rd family gases) A condensate trap assembly must be provided at the end of the manifold system before the hot gas vacuum fan. The minimum depth of the condensate collecting chamber shall be 305mm and the minimum depth of the condensate drain pipe ‘U’ trap shall be 457mm deep. The end cap of the collecting chamber to be fitted with a flush flanged tank connector. Any protrusion to be removed leaving the inside flush with end cap. The end cap should be sealed with silicon jointing compound and pop riveted in position. All condensate drains from the flue collecting chamber to the disposal point shall be corrosion-resistant material of not less than 22mm internal diameter. Copper or copper based alloy shall not be used for condensation drains. See reference BS 6896:2005. Condensate drain pipes must be protected against the effects of freezing. The Type ‘0’ and Type ‘2’ vacuum fans have bottom horizontal discharge with rectangular connections (flanged on the type 0) and must be mounted in that position by means of the fan support stool onto a suitable platform or brackets fixed to the building structure. For details of the fan outlet fixing holes see below. 305.0 457.0 Figure 4a. Condensate Trap Arrangement Figure 4c. Type ‘O’ Fan Outlet Dimensions Figure 4d. Type 2 Fan Outlet Dimensions 190 213 Figure 4b. Collecting Chamber Arrangement The manifold must be supported either side of the flexible coupler.

down holes see figure 5. Figure 4e. Conventional Flue Arrangement Roof Exit. Figure 4f. Conventional Flue Arrangement Wall Exit. Figure 4g. Stainless Steel Telescopic Through The Wall Arrangement (available for Type ‘O’ and Type ‘2’ fans) Where a conventional flue is to be installed, AmbiRad supply an aluminium transformation piece to which a 150mm (6ins) diameter flue must be attached. The length of flue which may be connected to the fan outlet must be adequately supported from the building structure. Figure 4h. Typical Low Fan Arrangement 305.0

2.6 0.8 Voltage 230V 1ph 230V 1ph Figure 5. Vacuum fan mounting details (Type ‘O’ fan illustrated) Hole Centers Hole Centers

Dos and don'ts of herringbone system Dos Don’ts Check for corrosive industrial process in proposed building - e.g. cleaning, electroplating, printers using sugar powder etc. Install system with extra 90° bends without asking AmbiRad if the system will operate correctly. Drain all flue ducts and seal all joints. Install flue with vertical rise without firstly fitting a drain point at it’s lowest level. Secure joints with pop rivets as well as sealing compound (refer to assembly instructions). Fit fan with outlet vertical or with top horizontal discharge. Fit drain traps before and after fans (see figs 4). Fit damper upside down or on it’s side. Fit expansion joints before fan and at intermediate points on the herringbone system. Fit damper wrong way round. (see fig14 page 31.) Run drains in galvanised steel or plastic pipes. Follow guide to combined flue heating system. Check design pressure drop. Run drains in copper or mild steel pipework.

The minimum clearances to combustible materials are given in the tables below. These minimum distances MUST be adhered to at all times. Figure 7.a Diagram illustrating the clearance to combustibles (U tube shown) VSUT / VSAUT 15/20 25/30 35/40 45/50 Above Reflector (VSUT NG ONLY) A 180 180 180 180 Above Reflector (VSAUT and ALL LPG ONLY) A1 280 280 280 280 Above Burner / Heater Outlet B 500 500 500 500 To the Sides C 900 1000 1100 1100 Below Tubes D 1500 1700 2100 2100 Horizontally from Heater Outlet (UNFLUED) E 1200 1200 1200 1200 End Wall (VSUT ONLY) F 500 500 500 500 A/A1 C E F D B

15/20 25/30 35/40 45/50 Above Reflector (VSLI/LF/LH/DL NG ONLY) A 150 150 150 150 Above Reflector (VSALI/LF/LH/DL NG and ALL LPG ONLY) A1 280 280 280 280 Above Burner B 500 500 500 500 To the Sides C 750 750 750 750 Below Tubes D 1500 1700 2100 2100 Horizontally from Heater Outlet (UNFLUED) E 1200 1200 1200 1200 End Wall F 500 500 500 500 Above Heater Outlet (FLUED) G 150 150 150 150 Above Heater Outlet (UNFLUED) G1 500 500 550 550 Figure 7.b Diagram illustrating the clearance to combustibles (VSLF shown) A/A1 B E F G/G1 C C D

force to the internal controls. A flexible hose is installed to allow safe linear expansion of the heater without creating undue stress on the gas supply pipe work. It is therefore important that a tested and certified hose assembly made to ISO 10380 2003, supplied with ½” BSP female cone seat adapters, is installed as per these instructions. It is also important to ensure that expansion is taken up in the body of the flexible hose, and not on its attachment to the pipe work. The cone seat adapter supplied on one end of the flexible gas hose provides a `swivel` action, and must be fitted on the burner using a ½” BSP barrel nipple to provide ease of disconnection for future servicing. This assumes that the heater and fixed gas supply to the isolating valve have been installed. The installation layout described below is the only method recommended by the institute of gas engineers, the hose manufacturer, and AmbiRad and must only be carried out by a qualified/competent gas engineer. fig.a fig.c Arrow denotes direction of expansion. Depending on the specific installation, the flexible gas hose may be routed to the gas cock at any of the following angles in relation to the burner: Vertical (fig.a) 45° angle (fig.b) 90° angle (fig.c) Any other position in between these angles is acceptable. A clearance distance ‘x’ of min 200mm must be observed to allow side door access . Care must be taken to observe the minimum pipe bend diameter (minimum 250mm, maximum 350mm) & pipe expansion distance (minimum 30mm, maximum 70mm) as shown in fig.e. Maximum bend diameter for the 1000mm hose is 450mm. The correct installation as shown will allow for approx 100mm of movement due to expansion. x x fig.b fig.d 1.7 Gas Connection and Supply Before installation, check that the local distribution conditions, nature of gas and pressure, and adjustment of the appliance are compatible. A competent or qualified engineer is required to either install a new gas meter to the service pipe or to check that the existing meter is adequate to deal with the rate of gas supply required. Installation pipes should be fitted in accordance with BS 6896:2005, so that the supply pressure, as stated in Table 4 will be achieved. It is the responsibility of the competent engineer to ensure that other relevant Standards and Codes of Practice are complied with in the country of installation. Pipes of smaller size than the heater inlet gas connection must not be used. The complete installation must be tested for soundness as described in the country of installation. The gas union service cock MUST be fitted in the gas supply close to the heater, but not onto the burner itself. Take care when making a gas connection fig.e 300 +/- 50mm Burne 50 +/- 20mm Figure 8. Correct Installation of Flexible Gas Connection

Supply 230V 50Hz single phase. Standard heater 116W. Herringbone 16W. Current rating 0.55 amp max (inductive). Fuse: external 3 amp. All electrical work should be carried out to IEE standards by a competent electrician. The electrical connection to the heater is made by means of a three pin plug-in power connector. Live, neutral and earth connections should be made via a flexible supply cable to the power connector and routed clear of the heater or tubes. The flexible supply cables should be of 0.5mm² and comply with BS 6500:2000. The wires in the mains lead are coloured in accordance with the following code: Green & Yellow Earth; Blue Neutral; Brown Live It is recommended the heater or group of heaters are controlled by thermostats, a time switch and if required manual control switches and a frost thermostat. We recommend use of AmbiRad approved controls. Please refer to control manual for siting and installation details. Where alternative manufactures controls are used, please refer to their instructions for their siting and installation details. Table 4 Gas Supply Pressures Gas Category I2H I3P Gas Type Natural Gas (G20) Propane (G31) Max Supply Pressure (mbar) 25 45 Min Supply Pressure (mbar) 17 25 Nominal Pressure (mbar) 20 37 Gas Supply Connection R½ ½in BSP Internal Thread Figure 9.a Typical VSUT/VSAUT Wiring Connections Fan plugs into burner Fused Spur fig.f fig.g The methods shown in fig.f and fig.g are unacceptable, due to undue stress on the hose & fittings. Fused Spur Figure 9.b Typical VSLF/VSALF Wiring Connections Fan plugs into burner

Fused Spur Figure 9.d Typical VSDL Wiring Connections Fused Spur Fused Spur Figure 9.c Typical VSLI/VSALI Wiring Connections Fan plugs into burner via plug/socket supplied. Extension wiring by others Fused Spur MAIN GREY YELLOW WHITE FLAME SENSOR IGNITOR 8 7 9 11 10 12 1 3 2 4 BLACK PURPLE WHITE LAMPS ON MAINS YELLOW GREY BLACK GRN/YEL BROWN SOLENOID GREEN/YELLOW SWITCH N.C. N.O. C. GREY EMC FILTER MAINS L N FAN N L ON BURNER BLUE BLUE BLUE VACUUM BROWN VALVE J.S.T. INPUT BLACK 1 3 2 VALVE J.S.T. BLUE GREEN/YELLOW

AmbiRad tube heaters can be operated as flued or unflued appliances in accordance with the relevant national requirements in the country of installation. 1.9.1 Unflued Radiant Heater Radiant tube heaters can be operated as unflued appliances so that the concentration of Carbon Dioxide (CO2) at positions where the air will be inhaled does not exceed 0.28%. BS EN 13410:2001 is a guide to achieving this requirement. If the building air change rate exceeds 1.5 per hour or if the heat input is less than 5W/m³, no additional ventilation is required. In addition to the ventilation requirements, con- sideration needs to be given to the possibility of condensation forming on cold surfaces. It should be noted that the clearance distance around the burner increases when the unit is operated unflued (see section 1.6). It should be ensured that the combustion gases do not impinge on any combustible materials. Mechanical Ventilation Mechanical ventilation must be installed to meet a minimum of 1.5 air changes per hour using appropriately sized fans and interlocked with the heaters. Natural Ventilation BS EN 13410:2001 should be used to size air vents to provide adequate ventilation, an example of this calculation is given below: Site Details: 20°c Internal Operating Temperature 0°c Outside Air Temperature 5m between high and low level vents Following the sizing procedure in BS EN 13410:2001 gives an air exit velocity of 1.6m/s. This equates to a free area vent at both high level and low level of 17.36cm²/kW free area. 1.9.2 Flued Radiant Heater In buildings having an air change rate of less than 0.5 per hour, additional mechanical or natural ventilation is required. For detailed information, please see BS6896:2005 section 5.2.2.2.1 Mechanical Ventilation Mechanical ventilation must be installed to meet a minimum of 0.5 air changes per hour using appropriately sized fans and interlocked with the heaters. Natural Ventilation Low level ventilation openings with a free area of at least 2cm²/kW shall be provided. See section 5.2.2.2.2.1. 1.10 Flue and Combustion Air Inlet - Options Induced Burners without Heat Exchangers Please refer to Figure 12 for options. Burner 2 Burner 1 Burner 3 1 phase Isolator Tail Pipe 1 phase 230V Exhaust Fan 230V 50Hz 13A Mains Supply Controller 0.75mm² Screened Cable Isolator Sensor Zone A Isolator Isolator Isolator Figure 11. Typical VSLH/VSALH Wiring Connections

A 127mm (5ins) Twin Wall Flue System B Fan Adaptor 7177-SUB (2501/2507 fan) or 7176-SUB (2506 fan) C Fan 2501/2507 or 2560 D Optional Ducted Air Intake. VSI-DA E Standard Air Intake (supplied as standard) Ventilation requirements are as detailed in section 1.9 Ducted air must be used in locations where there is airborne dust or where there is a polluted atmosphere e.g. Chlorinated Vapours. Maximum length = 9m Minimum diameter = 100mm Maximum no of bends = 2 Maximum flue length = 9.5m @ Ø125mm Maximum no of bends = 2 All flues must terminate vertically. For further information on flue runs, please refer to BS 5440 pt.1 2000 For non-flued installations, delete items A and B and rotate fan outlet to the HORIZONTAL position away from the burner. Products of Combustion Products of combustion Firing tube Ducted Air Intake D E A B C

A 127mm (5ins) Twin Wall Flue System B Tube to Flue Adaptor 75mm 201881 100mm 201882 C Flue Bend 7166 D Forced Burner E Standard end terminal (unflued) Ventilation requirements are as detailed in section 1.9 Ducted air must be used in locations where there is airborne dust or where there is a polluted atmosphere e.g. Chlorinated Vapours. Maximum length = 9m Minimum diameter = 100mm Maximum no of bends = 2 Products of Combustion Firing tube D B C A E Flued Installation For unflued installation, fit standard terminal supplied using grub screw provided Maximum flue length = 9.5m @ Ø125mm Maximum no of bends = 2 All flues must terminate vertically. For further information on flue runs, please refer to BS 5440 pt.1 2000

Tables 5a/b/c/d & e - Natural Gas (G20) Heater Model Heat Input kW Gas Flowrate (m³/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Weight (Kg) Fan Rating (A) Fan Type Gross Nett VS(A)15UT4 15.8 14.2 1.5 11.1 1.3 260x2219x670 41 0.5 2501 VS(A)15UT 15.0 13.5 1.4 10.7 1.3 240x3417x500 43 0.5 2501 VS(A)20UT 19.5 17.6 1.9 10.8 1.5 240x4142x500 50 0.5 2501 VS(A)25UT 23.5 21.2 2.3 8.0 1.8 240x5066x500 60 1.0 2507 VS(A)30UT 29.5 26.5 2.8 9.5 2.0 240x6029x500 70 1.0 2507 VS(A)35UT 36.0 32.4 3.4 9.7 2.3 260x5709x670 92 1.0 2507 VS(A)40UT 40.0 36.0 3.8 12.2 2.3 260x5709x670 92 1.0 2507 VS(A)45UT 44.0 39.6 4.2 8.9 2.9 260x7471x670 121 0.5 2560 VS(A)50UT 48.0 43.2 4.6 9.1 2.5 260x7471x670 121 0.5 2560 No of Injectors 1 Gas Connection ½ in BSP Internal thread Flue Nominal Bore mm (in) 125 (5) Unitary Fan Motor Details 230 volt 1 phase 50Hz Heater Model Gas Flowrate (m³/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Weight (Kg) Fan Rating (A) Fan Type Gross Nett VS(A)15LF6 13.8 12.4 1.3 9.8 1.3 390x5984x315 43 0.5 2501 VS(A)15LF8 13.8 12.4 1.3 9.8 1.3 390x8022x315 53 0.5 2501 VS(A)20LF7 19.5 17.6 1.9 12.0 1.5 390x6992x315 49 1.0 2507 VS(A)20LF10-5 19.5 17.6 1.9 12.0 1.5 390x10662x315 72 1.0 2507 VS(A)25LF8 23.5 21.2 2.3 9.5 1.8 390x8022x315 53 0.5 2501 VS(A)25LF10-5 23.5 21.2 2.3 9.5 1.8 390x10662x315 72 0.5 2501 VS(A)30LF10-5 29.5 26.6 2.8 11.5 2.0 390x10662x315 72 1.0 2507 VS(A)30LF12-5 29.5 26.6 2.8 11.5 2.0 390x12652x315 84 1.0 2507 VS(A)35LF10-5 36.5 32.9 3.5 11.5 2.3 390x10892x470 103 0.5 2501 VS(A)35LF13-5 36.5 32.9 3.5 11.5 2.3 390x13492x470 126 0.5 2501 VS(A)40LF13-5 40.0 36.0 3.8 12.5 2.4 390x13492x470 126 1.0 2507 VS(A)40LF16 40.0 36.0 3.8 12.5 2.4 390x16092x470 147 1.0 2507 VS(A)45LF13-5 45.0 40.5 4.3 11.0 2.9 390x13492x470 126 1.0 2507 VS(A)45LF16 45.0 40.5 4.3 11.0 2.9 390x16092x470 147 1.0 2507 VS(A)50LF13-5 50.0 45.0 4.8 13.6 3.0 390x13492x470 126 1.0 2507 VS(A)50LF16 50.0 45.0 4.8 13.6 3.0 390x16092x470 147 1.0 2507 Heat Input kW

Gas Flowrate (m³/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Weight (Kg) Fan Rating (A) Gross Nett VS(A)15LI8 15.0 13.5 1.4 10.7 1.3 390x7917x315 53 0.5 2501 VS(A)20LI7 19.5 17.6 1.9 10.8 1.5 390x6907x315 49 0.5 2501 VS(A)20LI10-5 19.5 17.6 1.9 10.8 1.5 390x10537x315 72 0.5 2501 VS(A)25LI8 23.5 21.2 2.3 8.0 1.8 390x7917x315 53 0.5 2501 VS(A)25LI10-5 23.5 21.2 2.3 8.0 1.8 390x10537x315 72 0.5 2501 VS(A)30LI10-5 29.5 26.6 2.8 9.5 2.0 390x10537x315 72 1.0 2507 VS(A)30LI12-5 29.5 26.6 2.8 9.5 2.0 390x12567x315 84 1.0 2507 VS(A)35LI10-5 36.0 32.4 3.4 9.6 2.3 390x10787x470 103 1.0 2507 VS(A)35LI13-5 36.0 32.4 3.4 9.6 2.3 390x13387x470 126 1.0 2507 VS(A)40LI13-5 40.0 36.0 3.8 12.2 2.3 390x13387x470 126 1.0 2507 VS(A)40LI16 40.0 36.0 3.8 12.2 2.3 390x16006x470 147 1.0 2507 VS(A)45LI13-5 44.0 39.6 4.2 8.9 2.9 390x13387x470 126 1.0 2507 VS(A)45LI16 44.0 39.6 4.2 8.9 2.9 390x16006x470 147 1.0 2507 VS(A)50LI13-5 50.0 45.0 4.8 10.0 2.5 390x13387x470 126 0.5 2560 VS(A)50LI16 50.0 45.0 4.8 10.0 2.5 390x16006x470 147 1.0 2507 Fan Type Heater Model Heat Input kW Gas Flowrate (m³/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Gross Nett VS(A)15LH6 15.0 13.5 1.4 10.7 1.3 390x5725x315 42 VS(A)15LH8 15.0 13.5 1.4 10.7 1.3 390x7763x315 52 VS(A)20LH7 19.5 17.6 1.9 10.8 1.5 390x6733x315 48 VS(A)20LH10-5 19.5 17.6 1.9 10.8 1.5 390x10363x315 71 VS(A)25LH8 23.5 21.2 2.3 8.0 1.8 390x7763x315 52 VS(A)25LH10-5 23.5 21.2 2.3 8.0 1.8 390x10363x315 71 VS(A)30LH10-5 29.5 26.6 2.8 9.5 2.0 390x10363x315 71 VS(A)30LH12-5 29.5 26.6 2.8 9.5 2.0 390x12393x315 83 VS(A)35LH10-5 36.0 32.4 3.4 9.6 2.3 390x10633x470 101 VS(A)35LH13-5 36.0 32.4 3.4 9.6 2.3 390x13233x470 124 VS(A)40LH13-5 40.0 36.0 3.8 12.2 2.3 390x13233x470 124 VS(A)40LH16 40.0 36.0 3.8 12.2 2.3 390x15832x470 145 VS(A)45LH13-5 44.0 39.6 4.2 8.9 2.9 390x13233x470 124 VS(A)45LH16 44.0 39.6 4.2 8.9 2.9 390x15832x470 145 VS(A)50LH13-5 50.0 45.0 4.8 10.0 2.5 390x13233x470 124 VS(A)50LH16 50.0 45.0 4.8 10.0 2.5 390x15832x470 145 Weight (Kg)

Flowrate (l/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Weight (Kg) Gross Nett VS(A)15UH 15.2 13.7 2.16 23.7 1.2 240x3417x500 42 VS(A)20UH 19.2 17.3 2.73 26.1 1.0 240x4142x500 49 VS(A)25UH 23.5 21.3 3.34 10.8 1.3 240x5066x500 59 VS(A)30UH 28.0 25.2 3.98 16.2 1.3 240x6029x500 69 VS(A)35UH 36.0 32.4 5.12 22.4 1.4 260x5709x670 91 VS(A)40UH 40.0 36.0 5.68 18.4 1.5 260x5709x670 91 VS(A)45UH 44.0 39.6 6.25 14.9 1.7 260x7471x670 120 VS(A)50UH 48.0 43.2 6.82 14.3 1.8 260x7471x670 120 Heater Model Heat Input kW Gas Flowrate (m³/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Weight (Kg) Gross Nett VS(A)15UH4 15.8 14.2 1.5 11.1 1.3 260x2219x670 40 VS(A)15UH 15.0 13.5 1.4 10.7 1.3 240x3417x500 42 VS(A)20UH 19.5 17.6 1.9 10.8 1.5 240x4142x500 49 VS(A)25UH 23.5 21.2 2.3 8.0 1.8 240x5066x500 59 VS(A)30UH 29.5 26.5 2.8 9.5 2.0 240x6029x500 69 VS(A)35UH 36.0 32.4 3.4 9.7 2.3 260x5709x670 91 VS(A)40UH 40.0 36.0 3.8 12.2 2.3 260x5709x670 91 VS(A)45UH 44.0 39.6 4.2 8.9 2.9 260x7471x670 120 VS(A)50UH 48.0 43.2 4.6 9.1 2.5 260x7471x670 120 Tables 6a/b/c & d. Technical Details - Propane Gas (G31) Heater Model Heat Input kW Flowrate (l/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Weight (Kg) Fan Rating (A) Fan Type Gross Nett VS(A)15UT 15.2 13.7 2.16 23.7 1.2 240x3417x500 43 0.5 2501 VS(A)20UT 19.2 17.3 2.73 26.1 1.0 240x4142x500 50 1.0 2507 VS(A)25UT 23.5 21.3 3.34 10.8 1.3 240x5066x500 60 1.0 2507 VS(A)30UT 28.0 25.2 3.98 16.2 1.3 240x6029x500 70 1.0 2507 VS(A)35UT 36.0 32.4 5.12 22.4 1.4 260x5709x670 92 0.5 2560 VS(A)40UT 40.0 36.0 5.68 18.4 1.5 260x5709x670 92 0.5 2560 VS(A)45UT 44.0 39.6 6.25 14.9 1.7 260x7471x670 121 0.5 2560 VS(A)50UT 48.0 43.2 6.82 14.3 1.8 260x7471x670 121 0.5 2560

Gas Flowrate (l/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Weight (Kg) Fan Rating (A) Gross Nett VS(A)15LI6 15.2 13.7 2.16 23.7 1.2 390x5879x315 43 0.5 2501 VS(A)15LI8 15.2 13.7 2.16 23.7 1.2 390x7917x315 53 0.5 2501 VS(A)20LI7 19.2 17.3 2.73 26.1 1.0 390x6907x315 49 0.5 2501 VS(A)20LI10-5 19.2 17.3 2.73 26.1 1.0 390x10537x315 72 0.5 2501 VS(A)25LI8 23.5 21.2 3.34 10.8 1.3 390x7917x315 53 1.0 2507 VS(A)25LI10-5 23.5 21.2 3.34 10.8 1.3 390x10537x315 72 1.0 2507 VS(A)30LI10-5 28.0 25.2 3.98 16.2 1.3 390x10537x315 72 1.0 2507 VS(A)30LI12-5 28.0 25.2 3.98 16.2 1.3 390x12567x315 84 1.0 2507 VS(A)35LI10-5 36.0 32.4 5.12 22.4 1.4 390x10787x470 103 1.0 2507 VS(A)35LI13-5 36.0 32.4 5.12 22.4 1.4 390x13387x470 126 1.0 2507 VS(A)40LI13-5 40.0 36.0 5.68 18.4 1.5 390x13387x470 126 1.0 2507 VS(A)40LI16 40.0 36.0 5.68 18.4 1.5 390x16006x470 147 1.0 2507 VS(A)45LI13-5 44.0 39.6 6.25 14.9 1.7 390x13387x470 126 0.5 2560 VS(A)45LI16 44.0 39.6 6.25 14.9 1.7 390x16006x470 147 0.5 2560 VS(A)50LI13-5 48.0 43.2 6.82 14.3 1.8 390x13387x470 126 0.5 2560 VS(A)50LI16 48.0 43.2 6.82 14.3 1.8 390x16006x470 147 0.5 2560 Fan Type Heater Model Heat Input kW Gas Flowrate (l/hr) Injector Pressure (mbar) Injector Size (mm) Size (h x l x w) Gross Nett VS(A)15LH6 15.2 13.7 2.16 23.7 1.2 390x5879x315 42 VS(A)15LH8 15.2 13.7 2.16 23.7 1.2 390x7917x315 52 VS(A)20LH7 19.2 17.3 2.73 26.1 1.0 390x6907x315 48 VS(A)20LH10-5 19.2 17.3 2.73 26.1 1.0 390x10537x315 71 VS(A)25LH8 23.5 21.2 3.34 10.8 1.3 390x7917x315 52 VS(A)25LH10-5 23.5 21.2 3.34 10.8 1.3 390x10537x315 71 VS(A)30LH10-5 28.0 25.2 3.98 16.2 1.3 390x10537x315 71 VS(A)30LH12-5 28.0 25.2 3.98 16.2 1.3 390x12567x315 83 VS(A)35LH10-5 36.0 32.4 5.12 22.4 1.4 390x10787x470 101 VS(A)35LH13-5 36.0 32.4 5.12 22.4 1.4 390x13387x470 124 VS(A)40LH13-5 40.0 36.0 5.68 18.4 1.5 390x13387x470 124 VS(A)40LH16 40.0 36.0 5.68 18.4 1.5 390x16006x470 145 VS(A)45LH13-5 44.0 39.6 6.25 14.9 1.7 390x13387x470 124 VS(A)45LH16 44.0 39.6 6.25 14.9 1.7 390x16006x470 145 VS(A)50LH13-5 48.0 43.2 6.82 14.3 1.8 390x13387x470 124 VS(A)50LH16 48.0 43.2 6.82 14.3 1.8 390x16006x470 145 Weight (Kg)

Gasses (kg/s) Flue Pressure (Pa) Maximum Flue Resistance Flue Gas Temp (°C) VS(A)15UT4 0.0110 200 - 250 VS(A)15UT 0.0115 VS(A)20UT 0.0117 VS(A)25UT 0.0139 VS(A)30UT 0.0171 VS(A)35UT 0.0193 VS(A)40UT 0.0210 VS(A)45UT 0.0212 VS(A)50UT 0.0261 VS(A)15LI6 0.0098 19 - 30 210 - 270 VS(A)20LI7 0.0119 VS(A)25LI8 0.0131 VS(A)30LI10-5 0.0171 VS(A)35LI10-5 0.0207 VS(A)40LI13-5 0.0216 VS(A)45LI13-5 0.0249 VS(A)50LI13-5 0.0256 VS(A)15LI8 0.0100 25 -35 160 - 210 VS(A)20LI10-5 0.0120 VS(A)25LI10-5 0.0145 VS(A)30LI12-5 0.0174 VS(A)35LI13-5 0.0194 VS(A)40LI16 0.0214 VS(A)45LI16 0.0237 VS(A)50LI16 0.0237 VS(A)15LF6 0.0075 18 - 25 250 - 290 VS(A)20LF7 0.0106 VS(A)25LF8 0.0127 VS(A)30LF10-5 0.0130 VS(A)35LF10-5 0.0157 VS(A)40LF13-5 0.0168 VS(A)45LF13-5 0.0189 VS(A)50LF13-5 0.0206 VS(A)15LF8 0.0077 20 - 30 180 - 240 VS(A)20LF10-5 0.0105 VS(A)25LF10-5 0.0126 VS(A)30LF12-5 0.0136 VS(A)35LF13-5 0.0161 VS(A)40LF16 0.0167 VS(A)45LF16 0.0190 VS(A)50LF16 0.0207 15 - 31 Table 7. Flue details - Natural Gas

Gasses (kg/s) Flue Pressure (Pa) Maximum Flue Resistance Flue Gas Temp (°C) VS(A)15UT 0.0119 15 - 31 190 - 240 VS(A)20UT 0.0132 VS(A)25UT 0.0147 VS(A)30UT 0.0154 VS(A)35UT 0.0264 VS(A)40UT 0.0281 VS(A)45UT 0.0300 VS(A)50UT 0.0300 VS(A)15LI6 0.0105 19 - 30 190 - 240 VS(A)20LI7 0.0135 VS(A)25LI8 0.0126 VS(A)30LI10-5 0.0180 VS(A)35LI10-5 0.0210 VS(A)40LI13-5 0.0220 VS(A)45LI13-5 0.0280 VS(A)50LI13-5 0.0263 VS(A)15LI8 0.0109 25 - 35 160 - 200 VS(A)20LI10-5 0.0149 VS(A)25LI10-5 0.0137 VS(A)30LI12-5 0.0185 VS(A)35LI13-5 0.0210 VS(A)40LI16 0.0224 VS(A)45LI16 0.0268 VS(A)50LI16 0.0262 Table 8. Flue details - Propane

Model Cold HB Pressure Hot HB Pressure mm H2O mbar mm H2O mbar VS(A)15UH4 21.4 2.1 12.7 1.2 VS(A)15UH 21.4 2.1 16.3 1.6 VS(A)20UH 19.4 1.9 15.3 1.5 VS(A)25UH 24.5 2.4 20.4 2.0 VS(A)30UH 23.5 2.3 19.4 1.9 VS(A)35UH 25.5 2.5 15.3 1.5 VS(A)40UH 29.6 2.9 17.3 1.7 VS(A)45UH 33.0 3.2 23.5 2.3 VS(A)50UH 33.0 3.2 23.5 2.3 VS(A)15LH6/DL12 18.4 1.8 13.3 1.3 VS(A)15LH8/DL16 18.4 1.8 14.3 1.4 VS(A)20LH7/DL14 19.4 1.9 14.3 1.4 VS(A)20LH10-5/DL21 18.4 1.8 14.3 1.4 VS(A)25LH8/DL16 20.4 2.0 16.3 1.6 VS(A)25LH10-5/DL21 22.4 2.2 18.4 1.8 VS(A)30LH10-5/DL21 24.5 2.4 19.4 1.9 VS(A)30LH12-5/DL25 33.6 3.3 25.5 2.5 VS(A)35LH10-5/DL21 27.5 2.7 13.3 1.3 VS(A)35LH13-5/DL27 20.9 2.0 12.7 1.2 VS(A)40LH13-5/DL27 22.4 2.2 12.2 1.2 VS(A)40LH16/DL32 21.4 2.1 14.3 1.4 VS(A)45LH13-5/DL27 27.5 2.7 16.8 1.6 VS(A)45LH16/DL32 26.5 2.6 17.3 1.7 VS(A)50LH13-5/DL27 30.0 2.9 18.3 1.8 VS(A)50LH16/DL32 27.5 2.7 17.8 1.7 Type ‘O’ Type ‘2’ Power (W) 550 120 Running current (overload setting) (A) 2.6 0.8 Phase Single Single Voltage (V) 230 230 Fan type Table 9. Herringbone Vacuum Fan characteristics

Model Cold HB Pressure Hot HB Pressure mm H2O mbar mm H2O mbar VS(A)15UH 21.4 2.1 16.3 1.6 VS(A)20UH 21.4 2.1 16.3 1.6 VS(A)25UH 24.5 2.4 21.4 2.1 VS(A)30UH 26.5 2.6 17.3 1.7 VS(A)35UH 35.7 3.5 21.4 2.1 VS(A)40UH 38.7 3.8 23.5 2.3 VS(A)45UH 37.7 3.7 23.5 2.3 VS(A)50UH 38.7 3.8 24.5 2.4 VS(A)15LH6/DL12 21.4 2.1 14.3 1.4 VS(A)15LH8/DL16 19.4 1.9 15.3 1.5 VS(A)20LH7/DL14 22.4 2.2 15.3 1.5 VS(A)20LH10-5/DL21 21.4 2.1 16.3 1.6 VS(A)25LH8/DL16 22.4 2.2 17.3 1.7 VS(A)25LH10-5/DL21 20.4 2.0 16.3 1.6 VS(A)30LH10-5/DL21 28.6 2.8 19.4 1.9 VS(A)30LH12-5/DL25 28.6 2.8 20.9 2.0 VS(A)35LH10-5/DL21 24.5 2.4 18.4 1.8 VS(A)35LH13-5/DL27 21.4 2.1 17.3 1.7 VS(A)40LH13-5/DL27 22.4 2.2 18.4 1.8 VS(A)40LH16/DL32 30.6 3.0 20.9 2.0 VS(A)45LH13-5/DL27 34.7 3.4 24.5 2.4 VS(A)45LH16/DL32 34.7 3.4 23.5 2.3 VS(A)50LH13-5/DL27 33.6 3.3 21.4 2.1 VS(A)50LH16/DL32 30.6 3.0 20.4 2.0

2.2.2 Turbulators (where fitted) Insert turbulator(s) into tube(s) ensuring the correct length and quantity are inserted into their respective correctly identified tube(s) as detailed in the assembly drawings. 2.2.3 Brackets There can be three types of brackets supplied with these heaters: • Type ‘A’ are suspending brackets with reflector fixing points. • Type ‘B’ are suspending brackets with no fixing points. • Type ‘C’ is a centre bracket to retain the reflector. (certain models only) Slide the bracket assemblies along to the tubes to the marked positions in their correct order as detailed in the assembly drawings. Tighten clamping ‘U’ bolt arrangement to tubes ONLY WHERE STATED on the assembly drawings. 2.2 Assembly Notes. 2.2.1 Tubes Identify and position tubes on trestles. For aesthetics it is advisable to position the tube seam and coupling fastener so that these cannot be seen from beneath the heater. Mark out the position of the bracket centres from the dimensions shown on the assembly drawings. PLEASE READ this section prior to assembly to familiarise yourself with the components and tools you require at the various stages of assembly. Carefully open the packaging and check the contents against the parts and check list. The manufacturer reserves the right to alter specifications without prior notice. Please ensure that all packaging is disposed of in a safe environmentally friendly way. For your own safety we recommend the use of safety boots and leather faced gloves when handling sharp or heavy items. The use of protective eye wear is also recommended. Pozidrive Screwdriver Saw Trestles Leather Faced Gloves Silicone Sealant & Gun 4 & 5mm Allen Keys Pop Riveter & 3/16” Rivets Tape Measure 13mm Socket Wrench With Extension 10mm, 12mm & 13mm Spanners Herringbone Systems Only 2.1 Tools Required. The following tools and equipment are advisable to complete the tasks laid out in this manual. Suitable alternative tools may be used. Please read these assembly notes in conjunction with the correct assembly drawings (figs 14 to 28).

the reflector through the brackets until the locating slots are aligned with the type A bracket fixing points. Slide the next reflector through the brackets and overlap the existing reflector until the locating slots line up with the same bracket fixing points Secure overlapped reflectors to bracket using M6 nuts, bolts and flat mud washers. 2.2.7 End Caps. On VSUT models only, position the end cap with no tube holes beneath the reflector profile at the U bend end with the end cap flanges facing inwards. Fasten to reflector using M5 pozi set pin and ‘Z’ clips. Position the end cap with tube holes beneath the reflector profile at the burner end with the end cap flanges facing inwards. Fasten to reflector using M5 pozi set pin and ‘Z’ clips. On VS(A)LF, VS(A)DL & VS(A)LH models only, position ONE end cap beneath the reflector profile at the open/fan/damper end with the end cap flanges facing inwards. Fasten to reflector using ‘Z’ clips. Position the other end cap beneath the reflector profile at the burner end with the end cap flanges facing inwards. Fasten to reflector using ‘Z’ clips. 2.2.3.1 Tube alignment sections For VS(A)50UT Angle Mounted Installations ONLY. To allow for differential expansion of the tubes, a tube alignment assembly is fitted to the first bracket on the fan side radiant tube. Position U bolt tube alignment sections over the tube and through bracket prior to clamping. 2.2.4 U Bend. For VS(A) ‘U’ tube heaters only. Slide the ‘U’ bend onto the tube ends with the clamping bolts facing upwards until the predefined stop position. Tighten clamping bolt arrangement using 13mm socket and wrench. 2.2.5 Couplers. For VS(A)LF, VS(A)LH, VS(A)LI and VS(A) 45/50UT tube heaters only. For joining radiant tubes, locate and position tube couplers at the end of the tubes so that the socket heads are facing outwards. Tighten clamping bolt arrangement to secure ensuring the bolts are not over tightened. To avoid damaging the heater whilst installing we recommend the heater chassis be suspended prior to fitting reflectors. All reflectors must be positioned/ attached to the brackets exactly as detailed in the assembly drawings. Remove the protective plastic coating.

Secure with grub screws. Note: The damper assembly must be located with its damper blade vertical and left in the closed position. The manifold tube is to be sealed and secured (as described below) to the damper assembly. 2.2.12 Herringbone Manifold Assembly. HB Models ONLY. After fixing the heaters in the desired position, the manifold system requires fitting. After allowing for a minimum of 75mm (3in) of penetration of the fitting into the tube, cut the tubes to the lengths required and remove all burrs and wipe off any grease or oil with a clean rag. Method of jointing aluminium tube Using the applicator gun exude 4mm diameter bead of high temperature silicon jointing compound externally round the end of the fitting and internally round the end of the tube. 2.2.8 Burner Assembly. On VS(A)UT only, slide the burner assembly onto the RIGHT HAND TUBE when viewed from above, ensuring it is fully engaged. Secure with grub screws. On VS(A)LF, VS(A)DL & VS(A)LH models only, slide the burner assembly onto the inlet end of the tube ensuring it is fully engaged. Secure with grub screws. 2.2.9 Fan Assembly. On U Tube heaters only, slide fan onto the left hand tube ensuring it is fully engaged. The fan discharge should face vertically for individually flued or horizontally away from the burner if unflued. 2.2.10 Condensate Box Assembly. On VS(A)DL models only, slide the condensate box flange onto the outlet end of the tube ensuring it is fully engaged. Secure with grub screws. 2.2.11 Herringbone Damper Assembly. On VS(A)UH and VS(A)LH models only, slide the damper assembly flange onto the outlet 2 x ‘Z’ clips End Cap M5 set pin These holes - Burner end only Fitting Manifold External bead of jointing compound Internal bead of jointing compound Manifold Tube Vacuum Test Point Damper Blade Emitter Tube FLOW FLOW

rotating movement to spread the jointing compound uniformly until a penetration of 75mm (3in) is achieved. Note The silicon jointing compound remains workable after application for only 5 minutes. Secure the joint by drilling through the tube and fitting and fix with three pop rivets at 12 o’clock, 4 o’clock and 8 o’clock positions. 4.8mm (3/16in) diameter pop rivets are recommended. 2.2.13 Detailed Assembly Drawings The following pages show the technical dimensional details of the VSUT/VSAUT, VSUH/VSAUH and VSLF/VSLH/VSALH, VSDL/ VSADL range of heaters. Please note the heater type, length and reference number from the delivery/advice note before identifying the correct model drawing.

161 FIGURE 1 SEE FIGURE 1 FIGURE 2 FIGURE 3 NOTE: SWAGE THIS END

SEE FIGURE 1 FIGURE 2 FIGURE 3 FIGURE 1 FIGURE 1 M6

FIGURE 1 FIGURE 1 M6 FIGURE 2 FIGURE 3 SEE FIGURE 2 SEE FIGURE 1

FIGURE 1 FIGURE 1 M6 FIGURE 2 FIGURE 3 SEE FIGURE 1 SEE FIGURE 2

FIGURE 1 FIGURE 1 M6 FIGURE 2 FIGURE 3 SEE FIGURE 1 SEE FIGURE 2

SEE FIGURE 1 FIGURE 1 SEE FIGURE 1 FIGURE 2 FIGURE 3

SEE FIGURE 1 SEE FIGURE 1 SEE FIGURE 1 FIGURE 1 FIGURE 2 LOCATE PINS IN HOLES PROVIDED IN TUBES NOTE: ALSO REFER TO ASSEMBLY IN- STRUCTIONS SECT 2.2.3.1 FOR ANGLE MOUNED HEATERS. 7471 1760 1200 1760 1760 NB. ONLY USED ON NAT GAS VARIANTS

NB. VLSF ONLY USED ON NAT GAS VARIANTS FIGURE 2 FIGURE 1 VSLF - 5984 (5829 UNFLUED) VSLI - 5879 NB. VLSF ONLY USED ON NAT GAS VARIANTS IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR.

FIGURE 1 FIGURE 2 NB. VLSF ONLY USED ON NAT GAS VARIANTS VSLF - 6992 (6837 UNFLUED) VSLI - 6907 NB. VLSF ONLY USED ON NAT GAS VARIANTS IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR. SECOND REFLECTOR OVERLAPS THIRD.

FIGURE 1 FIGURE 2 VSLF - 8022 (7867 UNFLUED) VSLI - 7917 NB. VLSF ONLY USED ON NAT GAS VARIANTS NB. VLSF ONLY USED ON NAT GAS VARIANTS IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR. SECOND REFLECTOR OVERLAPS THIRD.

FIGURE 1 FIGURE 2 VSLI - 10537 NB. VLSF ONLY USED ON NAT GAS VARIANTS NB. VLSF ONLY USED ON NAT GAS VARIANTS 2285 TURBULATOR (x1) - 30Kw NAT GAS 730 TURBULATOR (x1) - 30Kw PROPANE IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR. SECOND REFLECTOR OVERLAPS THIRD AND SO ON DOWN THE LENGTH OF THE TUBE. VSLF - 10622 (10467 UNFLUED)

FIGURE 1 FIGURE 2 VSLF - 12652 (12497 UNFLUED) VSLI - 12567 NB. VLSF ONLY USED ON NAT GAS VARIANTS NB. VLSF ONLY USED ON NAT GAS VARIANTS 4850 TURBULATOR (x1) - 30Kw VSLF NAT GAS 3560 TURBULATOR (x1) - 30Kw VSLI NAT GAS 1300 TURBULATOR (x1) - 30Kw PROPANE IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR. SECOND REFLECTOR OVERLAPS THIRD AND SO ON DOWN THE LENGTH OF THE TUBE.

FIGURE 1 FIG. 2 VSLF - 10892 (10737 UNFLUED) VSLI - 10787 NB. VLSF ONLY USED ON NAT GAS VARIANTS NB. VLSF ONLY USED ON NAT GAS VARIANTS IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR. SECOND REFLECTOR OVERLAPS THIRD AND SO ON DOWN THE LENGTH OF THE TUBE.

VSLF - 13492 (13337 UNFLUED) VSLI - 13387 NB. VLSF ONLY USED ON NAT GAS VARIANTS IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR. SECOND REFLECTOR OVERLAPS THIRD AND SO ON DOWN THE LENGTH OF THE TUBE. NB. VLSF ONLY USED ON NAT GAS VARIANTS 370 FIG. 2 FIGURE 1 2380 2500 5000 TURBULATOR (x1) - 35/45/50Kw VSLI 5000 TURBULATOR (x1) - 45/50Kw VSLF 3400 TURBULATOR (x1) - 35Kw VSLF 2600 TURBULATOR (x1) - 40Kw

FIG. 2 VSLF - 16091 (15936 UNFLUED) VSLI - 16006 NB. VLSF ONLY USED ON NAT GAS VARIANTS NB. VLSF ONLY USED ON NAT GAS VARIANTS FIGURE 1 IMPORTANT: ENSURE FIRST REFLECTOR OVERLAPS SECOND REFLECTOR. SECOND REFLECTOR OVERLAPS THIRD AND SO ON DOWN THE LENGTH OF THE TUBE.

Important When all the heaters have been installed the vacuum settings must be finally balanced in the hot condition. Before attempting to start up the heating system it is essential to perform the preliminary balancing of the vacuum level at each burner unit. Isolate each heater unit by unplugging the electrical connector and closing the gas isolating valve. Start all burners up and allow them to run for at least 20 minutes. Adjust the damper at exit of each heater using a 4mm Allen key in the damper blade securing screw. Observing the vacuum reading using a ‘U’ tube manometer connected to the vacuum test point (see fig29) each damper should be readjusted and set at a hot condition reading as shown in table 9 (NG) and table 10 (LPG) for the appropriate size of heater and model. Figure 29. HB Damper Assembly 3. Commissioning Instructions. These appliances should be commissioned by a qualified engineer. 3.1 Tools Required. The following tools and equipment are advisable to complete the tasks laid out in this manual. Suitable alternative tools may be used. 3.3 Balancing a DL System Important When all the heaters have been installed the vacuum settings must be finally balanced in the hot condition. As with a Herringbone system above, start both burners up and allow them to run for at least 20 minutes. Adjust the damper on the condensate box using a 4mm Allen key in the damper blade securing screw. Observing the vacuum reading using a manometer connected to the vacuum test point (see figure 30) each damper should be readjusted and set at a hot condition reading as shown in table 9 (NG) and table 10 (LPG) for the appropriate size of heater and model. Damper blade Vacuum test point Figure 30. DL Condensate Box Assembly Small Flat Head Screwdriver Manometer Pozidrive Screwdriver Leather Faced Gloves 4mm Allen Key 12mm Spanner Large Adjustable Spanners or 22, 26 & 27mm Spanners for fitting Of Gas Flex. 13mm Socket Wrench with Extension Ref Description A Radiant Emitter Tube B Manifold Tube C Vacuum Test Point D Damper Blade D A C B

been carried out to these instructions. NO YES Ensure gas and electricity supplies are isolated. Disconnect gas hose from burner Remove burner from tube and inspect burner head. (See servicing instructions) Replace burner on tube and secure. Open control housing and check that all components are securely fastened. Reconnect gas hose. Open isolating valve. Check soundness. Check thermostat is set to maximum and is calling for heat. Switch on electrical supply. The red neon should now be illuminated. If restarting heater a delay of 15s should be allowed. A successful ignition is indicated by the amber light illuminating and remaining illuminated. The heater should now run through its start up sequence and ignite. Turn off power and check that all components are securely fastened. Has the burner lit? Check operation on flame failure. Check gas pressure. Check gas pressure. Close control housing Leave the instructions with a responsible person. 3.4 Commissioning chart for VS series unitary heaters Gas Valve adjustment Injector pressure test point. Adjustment screw under cap to set injector pressure Gas inlet test point Check operation of air pressure switch.

These appliances should be serviced annually by a competent person to ensure safe and efficient operation. In exceptional dusty or polluted conditions more frequent servicing may be required. The manufacturer offers a maintenance service. Details available on request Soft Brush Manometer Pozidrive Screwdriver Leather Faced Gloves 4mm Allen Key Wrench with 13mm Socket 12mm Spanner 4.1 Tools Required. The following tools and equipment are advisable to complete the tasks laid out in this manual. Suitable alternative tools may be used. Large Adjustable Spanners or 22, 26 & 27mm Spanners for Fitting of Gas Flex. A Ducted Air Inlet B Induced Air Inlet Please refer to spares for burner components C Ignitor Assembly D Extruded Burner Head E Multi Hole Injector F Ignition Controller G Gas Valve H Pressure Switch I Neon's (Red/Amber) J Pepperpot Head 4.2 Burner Description. Figure 31. Induced Burner: Models VS(A)LI, VS(A)LH, VS(A)UH and VS(A)DL

B Fan Inlet Spigot C Fan Orifice plate D Fan Mount Plate and Support E Gasket Set 4.3 Burner Removal (All Options) Step 1 Isolate mains electric and gas supplies. Unplug the fan and mains electricity connectors. Step 2 Detach the gas supply as shown below, taking care to support the burner connection. Figure 32. Forced Gas Burner: Model VSLF G Gas Valve H Multi Hole Injector I Neon's (Red/Amber) J Ignition Controller K Extruded Burner Head L Pepperpot Head M Pressure Switch F Ignitor Assembly Please refer to spares for burner components N Jet Carrier

attachment slacken jubilee clip and remove the flexible hose from the fan. Step 4 Slacken the grub screw on the burner support casting using a 4mm Allen key to enable the burner to be removed from the radiant tube. Step 5 Carefully remove the burner to prevent it or any components from falling to the ground and position the assembly in a safe area. 4.4 Burner Gas Injector Servicing Step 1 Remove the burner support casting and gasket. Step 2 The burner head assembly can be disconnected by separating the connectors of the ignition lead assembly and removing the pressure switch silicon tube. Step 3 The gas injector can be inspected and replaced if contaminated or blocked. When replacing the gas injector use a 12mm spanner and ensure approved thread sealant is used. Step 4 Refit the burner support casting and replace the gaskets to ensure effective sealing. 4.5 Burner Head and Electrode Servicing Step 1 Check the pepper pot burner head for contamination. If necessary the head can be removed for cleaning of the inside of the burner head, see below.

replaced ensuring the 5 holes on the outer ring are aligned alongside the probes. Step 3 The condition of the ignitor assembly can be checked for deterioration. However, we advise replacement at each service to ensure continued reliability. Step 4 Detach the electrode assembly from the burner head by removing the two screws and separating the ignitor lead connectors. Step 5 Refit the electrode assembly and ensure the silicon sleeving is fitted as shown above to prevent arcing of the spark electrode. Step 6 Check the positions and spark gap as shown below. Step 7 The burner assembly is ready to refit after servicing the combustion fan and the radiant tube assembly. 4.6 Combustion Fan Assembly Induced Burner (Model VSLI/VSALI) Step 1 Loosen the clamp fitting on the flue Step 2 Loosen the 4mm grub screw. Step 3 The combustion fan can now be detached. Figure 33. Burner head detail

Step 5 Inspect the impeller and remove any dust with a soft brush. Step 6 Remove any dust from fan scroll and from around the motor. Step 7 Ensure the impeller rotates freely. Step 8 Refit components. 4.7 Combustion Fan Assembly Forced Burner (Model VSLF only) Step 1 On Forced burners with ducted air attachment slacken jubilee clip and remove the flexible hose from the fan. Step 2 Remove fan spigot fixings. Step 3 The combustion fan can now be detached. Step 4 Remove the fan orifice plate spinning. Step 5 Inspect the impeller and remove any dust with a soft brush. Step 6 Remove any dust from fan scroll and from around the motor. Step 7 Ensure the impeller rotates freely. Step 8 Refit components.

Step 1 Brush any dust from the exterior of the tubes. Step 2 Inspect the fan and burner tubes visually. If the tubes appear clean, skip to servicing the reflector. Step 3 Remove the U bend (or damper - HB products or condensate box - DL products) Step 4 Withdraw the turbulators from the appliance. Carefully noting their condition and position. Replace turbulators if necessary. Step 5 The turbulators should be cleaned with a soft brush. Step 6 If required the interior of the tubes can then be cleaned using an industrial vacuum cleaner or by using long poles and a scraper. Step 7 Refit components. 4.9 Reflector Servicing The condition of the reflectors should be noted. If necessary the reflectors can be cleaned with a mild detergent. This can significantly improve the efficiency of the appliance. 4.10 Inspection of Flue The flue needs to be inspected and cleaned if necessary or in accordance to the regulations of the country that the appliance is installed. 4.11 Re-commissioning After Service After servicing of the heater has been undertaken, it will be necessary to re-commission the heater as detailed in Section 3 of these instructions.

recommend that the components shown in this section should be stocked. Note Any spare part components that are not approved by AmbiRad could invalidate the approval of the appliance and validity of the warranty. 5. Spare Parts. 2015S Ignition Controller 201857 Nat Gas Valve Twin sol reg 220/240 Part No. Description See section 1.11 Injector 200358 Extruded Burner Head Item 201284 Ignitor Assembly Part No. Description 200988 Pepperpot Head Item 2175 Amber Neon (Burner On) 2180 Red Neon (Mains On) 200420 Jet Carrier (all except *) See Section 1.11 Combustion Fan 201571 Flame Plate (VS35/40/45 Propane ONLY) 201488 Gasket Set 201630 Jet Carrier * VS50 UT/UH/LI/LH/DL 900225-2 900225-3 900225-1 Cables: Spark Electrode (black) Rectification lead (purple) Earth lead (green/yellow) 201914 Propane Valve Twin sol reg 220/240 201905 Flame Plate (VS50 Propane ONLY) 201358 Flame Plate (VS15 ONLY Nat Gas & Propane) 201854 Flame Plate (VS20/25/30 Propane ONLY) 201676 201508 Pressure Switch: VSLF (Red) All others (Green)

Check: 1. Integrity of spark leads 2. Integrity of electrode assembly & spark gap 3. Burner controller Ensure gas & electricity supplies are enabled. Does the RED neon illuminate? Check: 1. Operation of any thermostat 2. Any external fuses 3. Correct voltage is selected YES Does the combustion fan run? Does the amber light illuminate after 10s purge? If the heater still fails to operate normally, please contact the AmbiRad service department. NO NO Does the vacuum switch `pull in`? Check: 1. Wiring harness & plugs 2. Vacuum switch operation 3. Replace fan Is the burner sparking? Does the gas valve open? Check: 1. Burner controller 2. Replace gas valve Check: 1. Vacuum switch tubes 2. Emitter tubes, air inlet & flue for obstructions 3. Operation of vacuum switch 4. Replace combustion fan NO YES Check: 1. Burner controller 2. Wiring harness 3. Amber neon faulty Check: 1. Burner inlet pressure 2. Burner nozzle pressure 3. Check live & neutral polarity 4. Check presence of good earth YES YES NO NO YES NO YES Does the amber light illuminate for 10s then go out? NO YES YES Is there power on the burner? Check: 1. Burner controller 2. Red neon faulty YES NO

7.1 Burner Controller Replacement Step 1 Slacken screw in burner lid and open the right hand burner access door. Step 2 Disconnect burner controller from the wiring harness. Step 3 Disconnect the HT Lead from burner controller. Step 4 Remove the two screws attaching the controller to the burner and remove. Step 5 Fit new burner controller. Step 6 Refit HT leads and refit burner controller to wiring harness. Step 7 Test product and close access door. 7.2 Air Pressure Switch Replacement Step 1 Disconnect the two silicone impulse tubes. Step 2 Remove the two screws as shown below. Step 3 The air pressure switch can now be removed. Step 4 Fit the new air pressure switch ensuring the impulse tubes are connected as shown below. Step 5 Test product and close access doors.

Step 1 Remove the burner assembly as described in section 4.3 Servicing. Step 2 Open the right hand access door and detach the burner controller from the wiring harness. Step 3 Open the left hand access door and detach the impulse hoses from the air pressure switch. Step 4 Remove the 4 screws holding the burner head onto the burner assembly. Step 5 The burner head can now be detached by disconnecting the impulse tube and the burner head wiring. Step 6 Detach the two screws holding the front of the gas valve. Step 7 Remove the four screws holding the rear burner plate in position. Step 8 Remove the rear plate. Step 9 The jet carrier, gas inlet, and wiring harness can now be detached from the gas valve. Step Screw Adjustment

Document reference number GB/VS/118/0711 8.1 To Start the Heater 1. Ensure gas supply is turned on. 2. Electrical supply to the controls is on. 3. Ensure that the controls are correctly set i.e.; • Clock is correctly set. • Heater program is correctly set. • Required room temp is correctly set 4. Once the heating controller ‘calls for heat’ power will be supplied to the heater(s). The red neon will then illuminate. 5. After a pre-purge period of 10 seconds the burner will ignite and the amber neon will then illuminate. 6. If lockout occurs press the lockout reset button (if available), or switch off electrical supply and restart after 15 seconds. 7. If lockout occurs three times consecutively switch off and isolate the gas and electricity supplies. Contact the AmbiRad Service department. 8.2. To Switch Off Heater 1. Switch off electrical supply to the heater. The burner will stop and the fan will shut off. 2. If the heater is to be switched off for periods in excess of one week it is highly recommended that both the gas and the electrical supplies are turned off. 8.3. Routine Maintenance between Service Intervals After ensuring that the heater is cold and mains electric isolated, cleaning of the reflectors with a soft cloth and a mild detergent (non solvent based cleaners only) in water can be undertaken. Additional removal of dust from the radiant tubes, burner and heat exchanger can be undertaken. 8.4 Frequency of Servicing The manufacturer recommends that to ensure continued efficient and safe operation of the appliance, the heater is serviced annually by a competent person e.g. every year in normal working conditions but in exceptional dusty or polluted conditions more frequent servicing may be required. The manufacturer offers a maintenance service. Details are available on request. For Service requirements, please contact AmbiRad. For further technical and service support visit our Support Information Database at www.s-i-d.co.uk AmbiRad is a registered trademark of AmbiRad Limited. Because of continuous product innovation, AmbiRad reserve the right to change product specification without due notice AmbiRad Limited Fens Pool Avenue Brierley Hill West Midlands DY5 1QA United Kingdom. Telephone 01384 489700 Facsimile 01384 489707 Email [email protected] Website www.ambirad.co.uk Technical Support www.s-i-d.co.uk Step 10 The two screws retaining the gas valve can then be removed. Step 11 The gas valve can now be replaced. Step 12 Refit all components in reverse order. Step 13 Ensure step screw is in the correct position as indicated in the previous diagram. (For Natural Gas burners ONLY). Step 14 Set gas pressures to data badge or as per section 1.11 and ensure reliable burner performance. Step 15 Test product and close access doors.