KOCOM KCV-544 Operating & Installation Manual

MANUAL VIDEOPHONE 4CH COLOR HANDSFREE ● 4CH Connection ● Compact Design(33mm) ● 7 inch digital LCD color monior ● Front Variation(Transparent Type, Mirror Type) ● Easy Icon Button ● OSD function ● Visitor Communication and Door Open ● Communicate with Guard Master phone ● Touch button ● Guard Phone, Lobby Phone Operating www.kocom.com KCV-544 MANUAL [Operating Installation Manual] KC-MC24 KC-MC20 KC-C60 KC-MC30 KLP-C420 Door Camera for KCV-544 KCV-544 CAMERA TALK

Warnings for Usage Cautions for Repairs and Maintenance ·Do not install this unit near the water and dust, for example, in a bathroom or near the washing machine. It caused fire and electric shock. ·Do not install this unit near the fire, for example, near kitchen sink, heater or the like. ·Do not install near the noxious gar such as Hydrogen Sulfide, metal power and the like. ·Do not install near the water and chemicals. ·Do not give any damage, break and modify the plug. Overloading, heating, pulling causes the damage. ·Do not place the plug near the heater. The damaged code causes fire and electric shock. Do not pull the power code when unplugging. ·The damaged code causes fire and eclectic shock. Must pull with plug. Do not touch with wet hands. It causes the electric shock. ·Do not use any other voltage, except the marked regular voltage. ·Do not use the power terminal at the units to other electric device except the designed device. ·Do not install the units at the leaking place if it doesn’t have any waterproof mark. Do not install the unit when the power is on. ·Install the circuit breaker after checking the safety such as electric shock and leakage. Turn off the power before you install or A/S ·Check the suitability of the lines for installing when you use the exiting lines. ·Do the wiring work by using the designed material. ·Connect the electric wire with the designed ways and ground. ·Do not connect with any other devices except the designed devices to compose the system. ·Unplug electric wire and communication lines from the units before moving to another place. For safe use, please stick to the following cautions. Cautions for safety ·Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. ·Set the device of the wall-mounted type not to fall. Falling from an earthquake causes personal injury. ·The law limits distributing the power lines to an authorized person from government. The work from an unaurhtorized person cause fire or electric shock. ·Place this unit securely on a stable surface. Serious damafe and/or injury may result if the unit falls. ·Do not set up this unit near the leaking place because it may expose you to dangerous voltages or other risks. ·Even if your product is water proof, do not install it slanted place of water leakage, which can a short circuit. ·Fix the product on the wall safely according to the installation guideline to prevent any damage or injury. ㆍDon’t put any stuff in 30cm around the monitor, not to block the air hole. ·The work of distributing wires needs skills and experiences. So please, for assistance, contact your dealer or call service center. ·The communication lines should be built in being distant from the power source. This may result in the risk of fire, electric shock and communication disorder. ·Setting the communication lines in a high humid place such as outside without any protection from rain causes the communication disorder. ·Keep the hook at the wall-mounted device safe. The hook may cause the physical injury. ·Think about the thickness and quality of wall material. The unqualified material may make the device fall. ·Keep the inside of the device clean. Having the dust inside without any cleaning for a long time causes the fire. If necessary, contact your dealer or service center to get cleaning service. Caution Warning ·Unplug this device when you want to check the inside. If there is no plug, please, turn off the circuit breaker. ·Unplug this device when you try to move it to another place. If the electric line is connected inside of the unit, please contact your dealer or service center. ·Please, save this manual after reading these instructions carefully. ·Read and understand all instructions to set up rightly. ·This Cautions for Safety may include items that are not contained in specifications of the product that consumer purchases. ·If you need assistance with the set-up or operation, please contact with A/S center. To help our customers to understand this manual, to prevent any personal injury or property damage, some marks are used in the manual. The marks and the drawing signs are below. Please, understand the marks before reading the manual. Sign to show what not to do. Sign to tell you that you should follow the instructions. Sign to tell you that you can't disassemble this unit. Sing to tell you that you need more attention including (high voltages, electric shock, danger, warning) Sign to tell you that you must unplug the unit. Mishandling the device with ignoring this sign may result in serious injury or death. Mishandling the device with ignoring this sign may result physical injury or material damage. The important marks in the manual. The meaning of the drawing signs.

Things You Need to Know Videophone Cautions Cautions for Abnormality Safety Instructions, Warnings and Cautions of Each System ·This product is designed as a home videophone and cannot use continuously like monitor camera. ·If there is temperature difference between inner part of camera and surrounding, dew condensation occurs on camera lens and may disturb image. If dew condensation is removed from camera lens, image quality recovers. ·White LED light examination range is narrower than camera shot range at night, so there is less amount of light at night than day. So it is difficult to see the face in low illumination condition due to noise increase on screen, but it is not from defect. ·Monitor screen (liquid crystal panel) is not in defect when some pixels always light or black out. ·Please install monitor and camera over 5cm away. Also, avoid installing at a place with too much noise, because too much noise around camera causes phone call inferiority. ·Do not place an object within 20cm in front of monitor. It causes phone call inferiority, especially because microphone is installed at the top of monitor. ·If strong light such as sunlight flows into camera module, screen saturation (or strange mark) and image shaking might occur. ·This is not a defect, so please do not install camera where a direct ray of light do not flow if possible. ·Separate the AC/DC lines with the hook of the wall-mounted type when installing. 쪾 ·Connect the lines after peeling the wires properly. ·Do not distribute signal line with AC line. ·Use the designed driver to connect the lines to terminal. ·Do not clean the LCD with the damp cloth for cleaning. Use the only dry and soft cloth. ·Do not install the main gate monitor at the leaking place. ·In some cases there is occurrence of product destruction, malfunction, noise mixing and picture quality deterioration due to mixing of other tool's induced. voltage or thunder with communication wiring of monitor/camera, monitor/extended monitor. Do not wire with power line such as outdoor wiring or AC power, or phones and other tools. ·You cannot use it if you incorrectly wire the AC voltage between monitor/camera, monitor/extended monitor. Call the store or agency where you purchased this product and consult to solve the problem. Beware that unfixable damage might be caused due to authorizing AC voltage on communication wiring of monitor/camera, monitor/extended monitor. ·Do not ever disjoint this product. It may cause electrocution accident when touching high-voltage circuit inside this product. ·Outside power authorizing this product must be confirmed of product description and use rated voltage. Beware that if higher voltage is authorized, unfixable damage might be caused due to product destruction. ·Power must be connected to domestic voltage (product rated voltage) consent or interior wiring. If connected to other motive power or inverter-type power, product destruction, noise mixing, and picture distortion may occur. ·Do not drop this product. Glass is used for monitor and might break, or cause other circuit inferiority. In such case, immediately turn down the power switch, and call to consult agency or store in which this product was purchased. ·Keep away from any conditions where water splatters or falls. Do not place anything containing water like a vase on the product. ·If you install a product nearby an antenna used for broadcast media, image could be distorted or mixed with a voice so that it is likely not to work properly in some functions. ·Avoid installing near tools with strong electromagnetic waves such as microwaves and cell phones, as it may cause a picture distorted or a voice with a noise. In that case, the product is likely not to work properly in some functions. ·Do not install monitor in following places. ① Above or around water heater, rice-cooker, heater ② Place exposed to direct rays of the sun ③ Place with temperature below 0'C such as cold store ④ Place with high humidity such as bathroom, washroom, heated room ⑤ Place with a lot of gas, dust, smoke ⑥ Dangerous place with sprays of water or chemicals ·Do not wipe with insecticide, drugs or chemicals such as thinner and alcohol, or it may damage the surface of this product. ·Beware of occurrence of image quality deterioration or malfunction from cause of humidity due to penetration of chemicals or water into camera’s urea resins. ·As in the picture, it prevents temperature difference of camera (outside) and monitor (inside), and removes dew condensation caused by humidity of camera window. ·Camera must be installed when wall cement is completely dry. ·When product is installed in winter below -5'C, wait for approximately 2 hours to connect. Dew formation in monitor and camera due to temperature difference inside and outside may cause product defect. ·Avoid installing monitor and camera in place directly exposed to heat or where gas noxiousness is highly occurring. ·Do not disassemble this unit at will as this device is composed by precision parts. 쪾 ·Install the unit by following the set-up instructions of Kocom. ·Do not touch or insert any foreign substances, for example, sticker, magnetic, opener and the like. ·Make U-type at the end of wires as the rain can effect on the system by following the wires during the rainy season. ·This unit is not designed for security purpose. 쪾·Do not handle the unit with the wet hands. ·Do not place a pot with water or a small metal material on the Units. ·Do not cover the ventilating opening or put any metal material in the units. 쪾 ·During thunderstorms, avoid using this unit. There may be a remote risk of an electric shock from lighting. ·Do not modify the unit. ·Open the main gate after checking ID if the image and sound system do not work. Call A/S ·Change the damaged electric code. ·Unplug this unit from plug socket and refer servicing to an authorized service center when the following conditions occur: ·If liquid has been spilled into the unit. 쪾·If the unit does not work normally by following the operating instructions. ·If the unit exhibits a distinct change in performance. ·If the unit has been dropped or physically damaged. ㆍThe mains plug, as a disconnection device, shall remain readily accessible by the user. ·Do not disassemble the back and cabinet cover. 4UPQ
VQ
17$
QJQF
VTJOH BEJBCBUJD
TVCTUBODFT
UP QSFWFOU
BJS
DJSDVMBUJPO 5VCJOH
#PY .POJUPS 1JQF $BNFSB 0VUEPPS
%PPS 3

and then fix it with hexagon screws and stick the finishing materials. ■ Monitor installation ■Door camera installation KC -MC30 KC-MC24 KC-MC20 KC-C60 ■ Directly connecting cut-off power cord with power wire 1) Do not do such electric work on your own. Installing product in this way requires reliance on electric installation man with electric work license. 2) Insulate with insulating tape while cutting off power cord and connecting with power wire so electric wire metal does not expose. Contact between exposed electric wires cause fire or electric shock accident. 3) Such electric work requires connection after interception of supplied power. 1) Remove wall-hanger bracket metal behind monitor. 2) Install wall-hanger bracket metal on 1 type box or wall with attached Vis. 3) Connect wiring to monitor back terminal referring to product connection diagram. 4) Hang monitor on wall-hanging metal, and fix monitor on wall- hanger bracket metal using attached Vis. 5) Plug monitor’s power plug into consent and check to see if the power switch is [ON] on the left side of monitor. Wall Screw (2X8mm) Main body supporter Screw (3X5mm) Wall Screw (4X16mm) Camera front Screw (4X10mm) Wall baby support Upward support Screw (2.6X6mm) Camera front Screw (4X10mm) ■ Monitor installation location ·Standard monitor installation height is about 1,500mm where screen center is at eye level. In this case, wall-hanging metal center (center of piping) is 1,450mm above ground level. ·Standard installation height ■ Caution of camera installation ·Avoid installing camera exposed to direct ray of light (and sun). ·Beware backlight and darkness of visitor’s face, which makes identification difficult. ·Avoid installing camera in places such as the following picture. (1) Place illuminating sky as background (2) Place with white wall reflecting direct ray of light (3) Place with direct ray of light ·Standard installation in height ■ Camera installation location ·Camera installation in height Standard camera installation height is when lens is about 1,400mm above the floor. In this case, camera stack center (piping box) is above 1,390mm above ground level. ·Standard installation in height Wall 4X25mm Screw 4X8mm Screw Rear Bracket Camera Terminal Block Camera front Wrench Name plate Standard wire strip specification : 6~7mm Standard wire (AWG) : 16~24(0.5mm~1.2mm) ※

Specifications ■ Door Camera [KC-MC24] [KC-MC30] [KC-MC20] [KC-C60] Screws for fixing main body on the wall Screws for fixing main body on the wall Finishing rubber Screws for fixing camera to main frame supporter Screws for fixing camera Screws for fixing camera to main frame supporter Screws for fixing camera main body supporter Upward adjusting supporter for lens angle Screw for fixing camera "L" wench Scre cap (KC-MB30) Screw for fixing camera Main body Supporter Main body Supporter Main body Supporter Main body Supporter 4X10mm 4X25mm 4X8mm 2.6X6mm 4X10mm or 4X16mm 3X5mm 2X8mm 5 ■ Wire ■ A Wall hanger frame 4 Pin cable for camera 4ea ■ Screw for fixing monitor 4X25mm 4ea (Flat head type) 3X8mm 1ea ■ Monitor Door Camera Wiring - Polarzied 4 lines(VCC[12V] / GND / VOICE / VIDEO) ※ Monitor Door Camera AC 90V-AC 240V 50/60Hz Stand by 1.8W(±20%), In load 12W(±20%) 0℃ ~ +40℃ 7 Inch color LCD Handsfree type Door camera wiring - Polarized 4 lines(VCC[12V] / GND / VOICE / VIDEO) Surface mount 223(W) x 130(H) x 33(D) mm Model No. Model No. KC-MC30 KC-MC24 KC-C60 KC-MC20 KCV-544 Power Source Power Consumption Operating Temperature LCD Communication Systerm Wiring Mount Type Dimension Power Source Power Consumption Operating Dimension Angle of Lens DC 12V ± 1V(Power from Monitor) Max. 3W -10℃ ~ +50℃ Diagonal 120˚ (angle adujstable) 110(W) x 158(H) x 39(D)mm 96(W) x 127(H) x 32(D)mm 95(W) x 127(H) x 34(D)mm 40(W) x 120(H) x 22(D)mm Diagonal 90˚ Diagonal 90˚ Diagonal 90˚

■ Monitor part ■ Camera part ·Left Side ·Front ·Back ·Bottom ① Monitor screen(LCD) : Output of image sent from camera. ② Microphone ③ Menu button : Each Menu Setup button. ④ Guard button : Function of Calling & Talking with Guard. ⑤ Monitoring button : Entrance door camera video monitoring & Talking function. ⑥ Door open button / Select button : Door open function during talking with visitor. Select button to move to menu mode. ⑦ Call volume adjustment switch : Adjustiong call sound in 3 steps. ⑧ Speaking volume adjustment switch : adjusting speaking volume transmitted From camera to monitor in 3 steps. ⑨ Camera terminal : Cannects camera with 4 wire polarity. ⑩ AC power cord(KCV-544) ⑪ Power switch : Use by Turning power ON / OFF ⑫ The terminal of updating the software FG(FRAME GROUND) ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ KC-MC30 KC-MC20 ⑤⑥ ① ② ③ ④ ④ ③ ② ① KC-MC24 KC-C60 ① VCC ② GND ③ Audio ④ Video ⑤&⑥ Door (Non-Polarity) ⑦ Camera angle knob (Only KC-MC/MB30) ⑧ Wire clamp ① ② ③ ④ ⑤ ⑥ KC-MC30 KC-MC20 ③ ② ④ ⑤ ① KC-MC24 KC-C60 ① C-Mic : To communicate with Monitor ② Camera Lens ③ LED ④ Speaker : When visitor calls, the voice from monitor comes out of the speaker. ⑤ Call Button : By pressing the button, the related house will be called. ⑥ Name plate ·The front side ·The back side 9 12 10 7 8 1 6 5 4 3 2 11

■ System configurations(System Mode) Lobby Phone (KLP-C420R) KVS-A4P / KVS-A8P Reapter KCV-544 Guard Phone (KAM-D340) 4WIRE 4WIRE ■ System configurations(Camera Mode) Door Opener External Power Input Polarized 4WIRE 4WIRE 4WIRE 4WIRE 2WIRE 2WIRE 2WIRE 2WIRE ■ Cable requirement - Based on distance from a camera to the monitor - Upto 100M : CAT5 cable Orange W/Orange ① VCC doble up Blue W/Blue ③ Audio doble up Green W/Green ② GND doble up Brown W/Brown ④ Video doble up ※ According to outside environment, you may view the images somewhat unclear. However, they do not result from any defect or trouble of the product. ※ CAT5 wire configuration ※ In case of more than 50m of CAT5 cable length, the screen and voice quality can get lower. But the sympthom is not a kind of fault. So less than 50m is recommended. - Upto 50M : TIV 0.65㎟ cable - Upto 100M : Over TIV 0.8㎟ cable - Upto 150M : TIV 0.8㎟ cable + RG-59 / U RG-59 / U (Coaxial cable) for Video signal (Connect core to Video & shield to GND) ■ Terminal ① CAMERA 1 ② CAMERA 2 1.VCC 2.GND 3.AUDIO 4.VIDEO 1.VCC 2.GND 3.AUDIO 4.VIDEO ③ CAMERA 3 ④ CAMERA 4 1.VCC 2.GND 3.AUDIO 4.VIDEO 1.VCC 2.GND 3.AUDIO 4.VIDEO ① ③ ② ④

2. Camera image appears on screen. (Monitoring time : 1~10 minute) 3. Press the Monitoring button to monitor the next camera. 4. Press the Monitoring button for 2 seconds to communicate during monitoring. 5. Press the menu button to finish monitoring. 8 ■ Communication with door camera ■ Call Guard Master on System mode set ■ Camera monitoring ■ Multi Camera Condition ■ Door open This function is for Guard Master, KLP-C420, KVS-A4P or KVS-A8P. Instructions for operation 1. If a call comes from Cam2 while Cam1 talking, Cam2 OSD appears at the edge of monitor and sounds Back Tone Melody with having power for 30 sec. 2. Under above status, if Cam3 calls on, Cam2 becomes off and Cam3 OSD appears at the edge of monitor and sounds Back Tone melody. 3. Under above status, if Cam4 calls on, Cam3 becomes off and Cam4 OSD appears at the edge of monitor and sounds Back Tone melody. H e l l o While 'Talk' on, push the Door Open button [ ] and the door will be opened. Door Open Time can be set from 1 sec ~ 10 sec. On Stand by, push the guard button [ ] H e l l o H e l l o When the guard picks up, the talk starts. (Communication time : 3 minutes) While Guard Talk on, push the guard button [ ] and Guard Talk finishes. Push the call button. The camera molody is turned on. You can hear call sound from all connected monitors, and camera image comes out on screen. (Standby time : 30 sec) H e l l o Push the entrance button [ ] and communicate with the door camera (Communication time : 1 minutes) Push the entrance button [ ] and stop the communication. H e l l o Videophone Camera 1 Camera 2 Camera 3 Camera 4

■ Sound Adjustment ■ Brightness Adjustment ■ Menu Setting 1. CAMERA 2. OPEN TIME 3. VIEW TIME 4. LANGUAGE 5. NTSC/PAL 6. DEFAULT CAMERA 1 CAMERA 2 CAMERA 3 CAMERA 4 : SET : 1 Sec : 1 Minute : ENGLISH : AUTO : MC20 3 : MC20 3 : NONE : SYSTEM [Menu] Buttons Up : [Guard] Button Down : [Talk] Button ENTER : [Door Open] Button 1. CAMERA : Select one of cameras 2. OPEN TIME : Door Open time of 0.1 ~ 10 sec, depending on the set time you input within 10 sec / Press time 3. VIEW TIME : Monitoring time of 1 Minute ~ 10 Minute 4. LANGUAGE: Select language (English/Russian/Spanish) 5. NTSC/PAL : Select image type 6. DEFAULT : Software becomes default 1. CAMERA 1 : Enabled to set up the camera and system 2. CAMERA 2 : Enabled to set up the camera and system 3. CAMERA 3 : Enabled to set up the camera and system 4. CAMERA 4 : Enabled to set up the camera and system ※Only 1 camera port can be used for SYSTEM Mode. ※Compatible camera : KC-MC24, MC20, C60, MC30, SYSTEM, NONE ※In case you choose “None“ in a camera setting and run monitoring, a monitor skips perceiving the camera set as “None”. Call Adjustment : See the side of monitor and find Call Vol. consisting of 3 level(High/Mid/Mute). Receiver Adjustment : While communicating, adjust R. Vol. consisting of 3 level(High/Mid/Low). - On Talk, push the Menu button [ ] and the brigtness icon will appear. At this point, adjust the brighteness with the keys, UP / DOWN / ENTER. ※Turn power switch off and on. Press Menu button [ ] within a minute. And setting menu screen is on with beep sound. Press Menu button [ ] to exit.

KOCOM Warranties the original purchaser of this product as follows. PRODUCT MODEL DATE PURCHASED WARRANTY PERIOD AGENCY ADDRESS 1. Name of the product. 2. Model number of the product. 3. The area of problem. 4. Phone number and address at which you can be contacted. 1) This product is produced under strict quality control and inspection procedures. 2) If this product breaks down during proper use as a result of product defect, KOCOM will repair it within one year from date of purchase free of charge. 3) The following cases will be subject to charge, even during warranty period: a. Breakdown during transport, or through careless treatment, by consumer. b. Breakdown cause by unauthorized repair, or system modification. c. Breakdown caused by natural disaster or power disorder. www.kocom.com E-mail : export @ kocom.co.kr This manual is based on the date as shown in the right and specifications are subject to change wihout notice for quality improvement KCV-544 P0408 SINCE 1976 KOREA COMMUNICATIONS CO.,LTD