Kramer VP-6A Operation & User’s Manual

2 5 Using Your VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor 5 5.1 Connecting the Balanced/Unbalanced Stereo Audio Output 7 5.2 Wiring the CAT5 LINE IN / LINE OUT RJ-45 Connectors 7 6 Technical Specifications 8 Figures Figure 1: Front and Rear Panels of the VP-6A 3 Figure 2: Underside of the VP-6A 4 Figure 3: Connecting the VP-6A 6 Figure 4: Connecting the Balanced Stereo Audio Output 7 Figure 5: Connecting the Unbalanced Stereo Audio Output 7 Figure 6: CAT5 PINOUT 7 Tables Table 1: Front and Rear Panel Features of the VP-6A 4 Table 2: Underside Features of the VP-6A 4 Table 3: CAT5 PINOUT 7 Table 4: Technical Specifications of the VP-6A 8

ADDENDUM: Included with user manuals for machines with a CAT5 connector This addendum describes the Power Connect feature used with Kramer machines, and the choice between STP and UTP CAT5 cables. Power Connect Feature1 The Power Connect feature lets you power a transmitter / receiver system by connecting just one power adapter to either the transmitter or the receiver. The other unit is fed over the same CAT5 cable. The Power Connect feature applies as long as the CAT5 cable is heavy gauge cable (that is, it can carry power). The distance does not exceed 50 meters on standard cable. For a distance of 100 meters, separate power supplies must be connected to the transmitter and to the receiver simultaneously, unless using heavy gauge CAT5 cable. Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP) The decision whether to use shielded twisted pair (STP) cable or unshielded twisted pair (UTP) cable depends on the nature of the application. It is recommended that in applications with high interference, shielded twisted pair (STP) cable will give better results. However, the shield itself does create a capacitance that degrades the frequency response of the machines. For shorter distances, of 50m or so, shielded twisted pair (STP) cable is preferred because it provides protection from interference (degradation is non-apparent). For a long range application, unshielded twisted pair (UTP) cable is preferred. However, the unshielded twisted pair (UTP) cable should be installed far away from electric cables, motors etc., which are prone to create electrical interference. 1 This section of the addendum is only relevant to machines that support this feature (for example, the TP-104; not the TP-100)

affordable solutions to the infinite range of problems that confront the video, audio and presentation professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 350-plus different models now appear in 8 Groups1, which are clearly defined by function. Congratulations on purchasing your Kramer VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor, which is ideal for:
 Presentation and multimedia applications that require high quality computer graphics and audio distribution to multiple monitors and/or projectors
 Long range graphics distribution for schools, hospitals, security, and stores The package includes the following items:
 VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor
 Power cord
 This user manual2 2 Getting Started We recommend that you:
 Unpack the equipment carefully and save the original box and packaging materials for possible future shipment
 Review the contents of this user manual
 Use Kramer high performance high resolution cables3 3 Overview The Kramer VP-6A is a high performance distribution amplifier for computer graphics (UXGA) video and audio signals. The VP-6A accepts:
 One computer graphics input: provides correct buffering and isolation, and distributes the signal to six outputs on 15-pin HD connectors, and one twisted pair output 1 GROUP 1: Distribution Amplifiers; GROUP 2: Video and Audio Switchers, Matrix Switchers and Controllers; GROUP 3: Video, Audio, VGA/XGA Processors; GROUP 4: Interfaces and Sync Processors; GROUP 5: Twisted Pair Interfaces; GROUP 6: Accessories and Rack Adapters; GROUP 7: Scan Converters and Scalers; and GROUP 8: Cables and Connectors 2 Download up-to-date Kramer user manuals from http://www.kramerelectronics.com 3 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com

Your VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor 2
 A stereo audio input signal: either1 an unbalanced stereo audio input signal on a 3.5mm mini jack, or a balanced stereo audio input signal on a 5-pin terminal block connector. The VP-6A outputs 12 stereo audio signals simultaneously: six unbalanced stereo audio signals on 3.5mm mini jacks, and six balanced stereo audio signals on 5-pin terminal block connectors. If the selected audio input is unbalanced, it is converted to balanced stereo audio; if the selected audio input is balanced, it is converted to unbalanced stereo audio The VP-6A can:
 Power the receiver over the same CAT5 cable
 Be used with the TP-122 XGA / Audio Line Receiver (converting the CAT5 signal to XGA, stereo analog and S/PDIF digital audio outputs) or with the TP-120 XGA Line Receiver (converting the CAT5 signal to an XGA output) In addition, the VP-6A features:
 Switches on the underside for ID Bit control and sync polarity
 Front panel controls for UXGA equalization, as well as left and right audio level controls
 A video bandwidth of 500MHz that ensures transparent operation at all graphics resolutions
 A transmission range of more than 300 ft. (more than 100 meters) over UTP cabling To achieve the best performance:
 Connect only good quality connection cables, thus avoiding interference, deterioration in signal quality due to poor matching, and elevated noise levels (often associated with low quality cables)
 Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer VP-6A away from moisture, excessive sunlight and dust In applications with high interference, shielded twisted pair (STP) cable will give better results. 4 Your VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor Figure 1 and Table 1 define the VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor: 1 Selected via a pushbutton

Your VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor 4 Table 1: Front and Rear Panel Features of the VP-6A # Feature Function 1 POWER Switch Illuminated switch for turning the unit ON or OFF 2 UXGA EQ. Trimmer Adjusts1 the video EQ. (equalization) compensation 3 LEFT Trimmer Adjusts1 the left output signal level 4 AUDIO LEVEL RIGHT Trimmer Adjusts1 the right output signal level 5 BAL. AUDIO INPUT Terminal Block Connector Connect to the balanced stereo audio source 6 UXGA INPUT HD15F Connector Connect to the computer graphics (UXGA) source 7 UNBAL/BAL IN SELECT Button Selects balanced stereo audio when released; selects unbalanced stereo audio when pushed in 8 UNBAL. AUDIO IN 3.5mm Mini Jack Connect to the unbalanced stereo audio source 9 BALANCED AUDIO OUT Terminal Block Connectors Connect to the balanced stereo audio acceptors (from 1 to 6) 10 UXGA OUT HD15F Connectors Connect to the computer graphics (UXGA) acceptors (from 1 to 6) 11 UNBALANCED AUDIO OUT 3.5mm Mini Jacks Connect to the unbalanced stereo audio acceptors (from 1 to 6) 12 LINE OUT RJ-45 Connector Connect to2 the LINE IN RJ-45 connector on a Kramer CAT5 receiver3 13 Power Connector with FUSE AC connector enabling power supply to the unit Figure 2 and Table 2 define the underside panel switches of the VP-6A: Table 2: Underside Features of the VP-6A # Feature Function 1 VS4 Switch Slide the switch to the right5 to change the VS polarity to negative polarity6; slide the switch to the left (Normal) to retain the polarity 2 HS4 Switch Slide the switch to the right5 to change the HS polarity to negative polarity6; slide the switch to the left (Normal) to retain the polarity 3 ID BIT 4 Switch Slide to the left to set to ON7; to the right to set to OFF 4 ID BIT 11 Switch Slide to the left to set to ON7; to the right to set to OFF Figure 2: Underside of the VP-6A 1 Insert a screwdriver into the hole and carefully rotate it, to trim the level 2 Using a UTP cable with CAT5 connectors at both ends (the PINOUT is defined in Table 3 and Figure 6) 3 For example, on the TP-120 XGA Line Receiver. Refer to the separate user manual: PT-110, PT-120, TP-120, WP-110, which can be downloaded at http://www.kramerelectronics.com 4 SYNC 5 By default, both switches are set to the left 6 Downgoing syncs 7 The default. Enabling the notebook or laptop to output a VGA signal to an external VGA monitor

5 5 Using Your VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor The example in Figure 3 illustrates how to output a computer graphics signal (and audio) from a computer to up to six local monitors, as well as how to transmit it over UTP cabling to a TP-122 XGA / Audio Line Receiver. To connect the VP-6A and a TP-122, do the following: 1. Connect a computer graphics source (for example, a computer) to the INPUT HD15F connector and to the UNBAL. AUDIO IN 3.5mm mini jack, for example, using a Kramer C-GMA/GMA cable1. Press in the IN SELECT button. Alternatively, connect a computer graphics source to the INPUT HD15F connector, and a balanced stereo audio source to the BAL. AUDIO INPUT 5-pin terminal block connector, and release the IN SELECT button. 2. Connect the OUTPUT HD15F connectors to up to2 six acceptors (for example, Local Display 1 to Local Display 6). 3. Connect up to2 12 stereo audio outputs3, that is, up to six:
 Unbalanced stereo audio OUT 3.5mm mini jacks, and
 Balanced4 stereo audio 5-pin terminal block connectors (see section
5.1) 4. Connect5 the CAT5 RJ-45 LINE OUT connector6 to the LINE IN RJ-45 connector on a Kramer CAT5 receiver, such as the TP-122 unit. 5. Connect the power cord7 to the VP-6A (not illustrated in Figure 3). 6. On the VP-6A:
 Adjust8 the UXGA cable compensation equalization level and/or the audio level, if required
 Set the ID BIT switches 4 and 11 on the underside to ON (by sliding them to the left). This would enable a notebook or laptop (if connected instead of a computer) to output an UXGA signal to an external VGA monitor 1 XGA HD15M +Audio jack to XGA HD15M +Audio jack (not supplied). The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com. Alternatively, you can connect an XGA source to the XGA INPUT HD15F connector, and a separate audio source to the UNBAL. AUDIO IN 2 When not all outputs are required, connect only the outputs that are required and leave the other outputs unconnected 3 Note, that if the selected audio input is unbalanced, it is converted to balanced stereo audio; if the selected audio input is balanced, it is converted to unbalanced stereo audio 4 By wiring the balanced outputs as unbalanced (see Figure 5) you can output 12 unbalanced stereo audio outputs 5 Via UTP cabling, with a range of more than 300ft (>100m): see section
5.1 6 The TP-122 (or TP-120) may be powered via this connector (instead of via the 12VDC external supply) 7 We recommend that you use only the power cord that is supplied with this machine 8 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level

Using Your VP-6A 1:6 UXGA / Audio / +1 CAT5 Distributor 6
 If necessary, slide the VS and HS switches to the right to output negative sync polarity (or leave them in the left position (Normal) to retain the sync polarity) 7. On the TP-122:
 Connect the XGA OUT HD15F connector to the XGA acceptor (for example, a display), and connect the AUDIO OUT S/PDIF RCA connector to the digital audio acceptor (for example, an AV Receiver), and the ANALOG 3.5mm mini jack to the analog audio acceptor (for example, a stereo audio recorder)
 Adjust1 the video output signal level and/or cable compensation equalization level, if required
 If necessary, set the H SYNC and V SYNC switches2, on the underside Figure 3: Connecting the VP-6A 1 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level 2 By default, both switches are set down (for negative V SYNC and H SYNC polarity)

7 5.1 Connecting the Balanced/Unbalanced Stereo Audio Output Figure 4 and Figure 5 illustrate how to wire a balanced/unbalanced stereo audio output connection: Figure 4: Connecting the Balanced Stereo Audio Output Figure 5: Connecting the Unbalanced Stereo Audio Output 5.2 Wiring the CAT5 LINE IN / LINE OUT RJ-45 Connectors Table 3 and Figure 6 define the UTP CAT5 PINOUT, using a straight pin to pin cable with RJ-45 connectors: Table 3: CAT5 PINOUT EIA /TIA 568A EIA /TIA 568B PIN Wire Color PIN Wire Color 1 Green / White 1 Orange / White 2 Green 2 Orange 3 Orange / White 3 Green / White 4 Blue 4 Blue 5 Blue / White 5 Blue / White 6 Orange 6 Green 7 Brown / White 7 Brown / White 8 Brown 8 Brown Pair 1 4 and 5 Pair 1 4 and 5 Pair 2 3 and 6 Pair 2 1 and 2 Pair 3 1 and 2 Pair 3 3 and 6 Pair 4 7 and 8 Pair 4 7 and 8 Figure 6: CAT5 PINOUT

Technical Specifications 8 6 Technical Specifications Table 4 includes the technical specifications: Table 4: Technical Specifications1 of the VP-6A INPUTS: VIDEO: 1 XGA on an HD15F connector AUDIO: 1 unbalanced stereo audio on a 3.5mm mini jack; 1 balanced stereo audio on a 5-pin terminal block connector OUTPUTS: VIDEO: 6 XGA on HD15F connectors; 1 RJ-45 connector AUDIO: 6 unbalanced stereo audio on 3.5mm mini jacks; 6 balanced stereo audio on 5-pin terminal block connectors MAX. OUTPUT LEVEL: VIDEO: 1.7Vpp AUDIO: balanced and unbalanced 26Vpp BANDWIDTH (-3dB): VIDEO: 500MHz AUDIO: balanced and unbalanced >100kHz; S/PDIF: 22kHz (TP-122 OUT) DIFF. GAIN: 0.09% DIFF. PHASE: 0.01 Deg. K-FACTOR: <0.05% S/N RATIO: VIDEO: 72dB AUDIO: balanced and unbalanced out 88dB CONTROLS: XGA: 0 to +10dB EQ.; AUDIO: 0 to +9.9dB Level (balanced/unbalanced) COUPLING: VIDEO: DC AUDIO: Input: AC; Output: DC AUDIO THD + NOISE: 0.015% AUDIO 2nd HARMONIC: 0.004% POWER SOURCE: 230 VAC, 50 / 60 Hz (115VAC, U.S.A.) 17.5VA DIMENSIONS: 19 inch (W), 7 inch (D) 1U (H) rack mountable WEIGHT: 2.7 kg. (6 lbs.) approx. ACCESSORIES: Power cord 1 Specifications are subject to change without notice

following terms. HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase. WHO IS PROTECTED? Only the first purchase customer may enforce this warranty. WHAT IS COVERED AND WHAT IS NOT COVERED Except as below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distributed by Kramer, or which is not purchased from an authorized Kramer dealer. If you are uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents listed in the web site www.kramerelectronics.com. 2. Any product, on which the serial number has been defaced, modified or removed. 3. Damage, deterioration or malfunction resulting from: i) Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature ii) Product modification, or failure to follow instructions supplied with the product iii) Repair or attempted repair by anyone not authorized by Kramer iv) Any shipment of the product (claims must be presented to the carrier) v) Removal or installation of the product vi) Any other cause, which does not relate to a product defect vii) Cartons, equipment enclosures, cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items. We will not pay for the following: 1. Removal or installations charges. 2. Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These costs are the responsibility of the Kramer dealer from whom the product was purchased. 3. Shipping charges. HOW YOU CAN GET WARRANTY SERVICE 1. To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center. 2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage, and should be included in any shipment of the product. Please also include in any mailing a contact name, company, address, and a description of the problem(s). 3. For the name of the nearest Kramer authorized service center, consult your authorized dealer. LIMITATION OF IMPLIED WARRANTIES All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to the length of this warranty. EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer shall not be liable for: 1. Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss of time, commercial loss; or: 2. Any other damages, whether incidental, consequential or otherwise. Some countries may not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place. NOTE: All products returned to Kramer for service must have prior approval. This may be obtained from your dealer. This equipment has been tested to determine compliance with the requirements of: EN-50081: "Electromagnetic compatibility (EMC); generic emission standard. Part 1: Residential, commercial and light industry" EN-50082: "Electromagnetic compatibility (EMC) generic immunity standard. Part 1: Residential, commercial and light industry environment". CFR-47: FCC Rules and Regulations: Part 15: “Radio frequency devices Subpart B – Unintentional radiators” CAUTION!
Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment.
Use the supplied DC power supply to feed power to the machine.
Please use recommended interconnection cables to connect the machine to other components.

Web site: www.kramerelectronics.com E-mail: [email protected] P/N: 2900-000090 REV 1 For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Caution Safety Warning: Disconnect the unit from the power supply before opening/servicing.