Crestron CLW-SLVS1RF Manuals

infiNET™ SWITCHES
Introduction
Features and Functions
The CLW-SW1RF (-SW1RF) and CLW-SW4RF
(-SW4RF) are stand-alone wall box switches that can also
act as wireless infiNET™ devices that report to a
Crestron® control processor through an infiNET gateway
such as the Crestron C2N-MNETGW.
These switches are a part of Crestron’s line of lighting
products using infiNET mesh network technology. infiNet
technology is “Wi-Fi” friendly and provides fault
tolerance and increased effective signal strength as
network devices are added.
Up to 30 infiNET devices (including C2N-MNETRPT
infiNET Repeaters) can communicate with one
C2N-MNETGW Gateway. If more devices are needed,
more C2N-MNETGW gateways may be added to a
Cresnet® network.
The infiNET switches operate on the 2.4 GHz “ISM
band” (2400 MHz to 2483.6 MHz) at 10 mW. The output
power of these devices allow RF signals to travel
approximately 150 feet indoors and 250 feet outdoors
(subject to site-specific conditions) without the use of
repeaters or other infiNET devices. The range is
dependent on construction of the building, obstructions,
and RF interference from other devices. The location of
the switch is an important factor in determining RF
performance. Adding more infiNET devices or repeaters
to the network effectively increases the range, strength,
and reliability of the network.
The -SW1RF and -SW4RF feature a three-position mode
selection switch. For more information, refer to the latest
version of the infiNET Switches Operations Guide (Doc.
6397) which is available from the Crestron website
(www.crestron.com/manuals). In the absence of control
system communications, the switch can still be used to
control the attached load.
The CLW-SWS1RF (-SWS1RF) and CLW-SWS4RF
(-SWS4RF) are similar to the -SW1RF and -SW4RF
(respectively) with the added capability of working with a
slave unit (CLW-SLVS1RF) in a multi-switch / single
circuit application.
The CLW-SLVS1RF (-SLVS1RF) is a slave unit that
when used in conjunction with the -SWS1RF or the
-SWS4RF acts as an additional switch control point in a
multi-switch / single circuit application. It does not
connect to a Cresnet system and cannot be used without a
-SWS1RF or -SWS4RF. The -SLVS1RF does not have a
mode selection switch. It will emulate the RUN mode of
the -SWS1RF (even if connected to a -SWS4RF) unless
the mode selection switch of the master is set to “OFF”.
For more information, refer to the latest version of the
infiNET Switches Operations Guide (Doc. 6397) which is
available from the Crestron website.
These switches are available in white, almond, and black.
White units are designated by part numbers ending in
“W”. Almond units are designated by part numbers
ending in “A”. Black units are designated by part numbers
ending in “B”. Each switch can be covered with a
decorative faceplate (not supplied).
Specifications
Following are specifications for the -SW1RF, -SW4RF,
-SWS1RF, -SWS4RF, and -SLVS1RF.
CLW-SW1RF/-SW4RF, CLW-SWS1RF/-SWS4RF, &
CLS-SLVS1RF Specifications
SPECIFICATION
DETAILS
Power Requirements
Line Power, 120 VAC, 60 Hz
Operating Frequency
2400 MHz to 2483.6 MHz
(802.15.4 compliant)
RF Output Power
10 mW
Operating Ranges¹
 Typical Distance
 Indoors
 (without repeater)
 Typical Distance
Outdoors
150 ft
250 ft
(subject to site-specific
conditions)
Default MNET ID
SW1RF/SW4RF: 01/01
SWS1RF/SWS4RF: 01/01
Switch Type
Single-Pole, Single-Throw
Load Type
Incandescent, Tungsten-
Halogen, Fluorescent / High
Intensity Discharge (HID),
Electronic Low Voltage,
Magnetic Low Voltage, Neon /
Cold Cathode, Ceiling Fan
2-Series Control System
Update File
2,3
Version 3.154 or later
Load Ratings
4
Incandescent /
Tungsten-Halogen
-SW1RF/-SW4RF: 1000W
-SWS1RF/-SWS4RF: 1000W
-SLVS1RF: N/A
Magnetic Low Voltage
5
-SW1RF/-SW4RF:
1000VA/750W
-SWS1RF/-SWS4RF:
1000VA/750W
-SLVS1RF: N/A
Neon / Cold Cathode
5
-SW1RF/-SW4RF:
1000VA/750W
-SWS1RF/-SWS4RF:
1000VA/750W
-SLVS1RF: N/A
(continued on following page)
Crestron Electronics, Inc.
Installation Guide - DOC. 6293A
15 Volvo Drive   Rockleigh, NJ 07647
(2011322)
Tel: 888.CRESTRON
09.06
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.

Crestron CLW-SW1/4RF,
CLW-SWS1/4RF, CLW-SLVS1RF
infiNET™ Switches
Operations Guide

Crestron CLW-SW1/4RF,
CLW-SWS1/4RF, CLW-SLVS1RF
infiNET™ Switches
Operations Guide