CyberData 011472 Manuals

Quick Reference 931511E © 2019, CyberData Corporation, ALL RIGHTS RESERVED © 2019, CyberData Corporation, ALL RIGHTS RESERVED 931511E Quick Reference RTFM Switch Contacting CyberData 1.0" [25 mm] Paper Clip Access RTFM RTFM Access The RTFM switch access will be on the top side of the horn hidden under a screw that will be used to keep the unit secured. To access the RTFM, complete the following steps: 1. Remove the screw to gain access to the RTFM button (see the figure below). 2. Use a paper clip to feed through the hole to press the RTFM button (see the figure below). Announce the IP Address To broadcast the device’s current IP address, press and hold the RTFM switch for a couple of seconds and then release it. Restore the Factory Default Settings To restore the factory defaults, complete the following steps: 1. Press and hold the RTFM switch until you hear the device announce the words, “restoring defaults” and “rebooting”. 2. Release the RTFM switch. The device will be restored to the factory default settings. Access RTFM Screw Cover Sales: (831) 373-2601 ext. 334 Support: 831-373-2601 ext. 333 Support Website: http://support.cyberdata.net/ RMA Department: (831) 373-2601 ext. 136 RMA Email: [email protected] RMA Status: http://support.cyberdata.net/ Warranty Information: http://support.cyberdata.net/ Corporate Headquarters CyberData Corporation 3 Justin Court Monterey, CA 93940, USA Phone: 831-373-2601 Fax: 831-373-4193 http://www.cyberdata.net/ Typical System Installation Getting Started • Download the Operations Guide PDF file from the Documents tab at the following webpage: https://www.cyberdata.net/products/011472 • Create a plan for the locations of your paging amplifiers. • WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes. • WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. • WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant. • WARNING: The InformaCast Enabled IP66 Outdoor Horn enclosure is not rated for any AC voltages! Parts Parameter Factory Default Setting IP Addressing DHCP IP Addressa a. Default if there is not a DHCP server present. 10.10.10.10 Web Access Username admin Web Access Password admin Subnet Maska 255.0.0.0 Default Gatewaya 10.0.0.1 *See the Operations Guide for more installation options. Compliant Non-PoE Ethernet Switch VoIP Phone InformaCast Server InformaCast Enabled IP66 Outdoor Horn (1) Assembly The IP Endpoint Company Installation Quick Reference InformaCast Enabled IP66 Outdoor Horn 011472

Quick Start Guide 931512B The IP Endpoint Company 1.0 Out-of-Box and Prior to Final Installation 3.1. Verify that you have received all of the parts listed on the Installation Quick Reference placemat. 3.2. Download the current manual, otherwise known as an Operations Guide, which is available in the Downloads tab at the following webpage: https://www.cyberdata.net/products/011472 Note You can also navigate to the Downloads tab by going to www.CyberData.net and following the steps that are indicated by the following figures: 2.0 Select Power Source IEEE 802.3af or 802.3at PoE Switch IEEE 802.3af or 802.3at PoE Injector Set PoE power type to Class 0 = 15.4W OR for high power PoE+ set Class 4 = 30W CAT6 cable recommended— for longer distances Be sure you are using a non-PoE switch or port Make sure port is not in trunk mode Set port to full duplex/ 100mbps Spanning Tree Protocol (STP) must be disabled or Portfast enabled 1 3 2 OUR PRODUCTS VOIP PRODUCTS A B 011472 INFORMACAST ENABLED Downloads IP66 OUTDOOR HORN INFORMACAST ENABLED C InformaCast Enabled IP66 Outdoor Horn Quick Start Guide