DMP Electronics SR3 Manuals

INSTALLATION AND PROGRAMMING GUIDE SR3 Bluetooth and Proximity Reader

SR3 Bluetooth and Proximity Reader Quick Start Guide Wire the Reader WARNING: Do not press and hold the button on the back of the reader. This procedure clears the unit’s memory and firmware, which renders the device inoperable until it is reconfigured and re-enrolled. Disconnect power before wiring the reader. After wiring and reconnecting power, the LED turns steady yellow, indicating that the reader is ready for enrollment. Follow these guidelines when wiring the reader: Connections must be made in accordance with NFPA 70: Do not connect to a receptacle controlled by a switch. Minimum wire gauge is 24 AWG with a maximum single wire run length of 500 ft (150 m). Wire the Reader Connect the reader wires to the access controller according to the purpose of each controller terminal. Refer to Table 1 and the examples that follow for details. For wiring and power requirements, refer to “Wiring and Power”. Caution: Do not cut the braided directional antenna wire. Wrap it around and secure it to the wiring harness for future use. WIRE COLOR PURPOSE TYPICAL X1 SERIES TERMINALS TYPICAL 734 SERIES TERMINALS TYPICAL KEYPAD WIRES Red Power (Positive) R1 RED Red Black Ground (Negative) B1 BLK Black White Data 1 W1 WHT White Green Data 0 G1 GRN Green/White Blue Green LED LC LC None Orange Beeper* (optional) BC RA None Purple Red LED (optional) None None None Yellow Smart Card Present (optional) None None None Copper, braided - Do not cut Directional Antenna (optional) None - Do Not Cut None - Do Not Cut None - Do Not Cut * If connected, the orange wire (beeper) mimics keypad beeping. Table 1:  Wire Connections SR3 Installation and Programming Guide | Digital Monitoring Products 1 GET STARTED SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand reader protocol to communicate with door controllers or access control modules. Procedure The installation must follow this procedure: Step 1 (Technician): Install the reader. Step 2 (Technician): Enroll and associate the reader with a system in Tech APP. Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin. Step 4 (Customer): Assign credentials to a user in Virtual Keypad. Step 5 (End User): Bind a mobile credential to a user’s device in Virtual Keypad. Step 6 (End User): Use the credential at the SR3 Bluetooth Reader. This guide walks you through all 6 steps. What’s Included What You’ll Need ▶ Drill ▶ If mounting with wall anchors, a 5/16” (8.0 mm) drill bit ▶ If mounting without wall anchors, a 5/64” (2.0 mm) drill bit ▶ #1 Phillips screwdriver ▶ #2 Phillips screwdriver ▶ Pliers ▶ Wire connectors ▶ Electrical tape SR3 Installation and Programming Guide | Digital Monitoring Products 1 GET STARTED SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand reader protocol to communicate with door controllers or access control modules. Procedure The installation must follow this procedure: Step 1 (Technician): Install the reader. Step 2 (Technician): Enroll and associate the reader with a system in Tech APP. Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin. Step 4 (Customer): Assign credentials to a user in Virtual Keypad. Step 5 (End User): Bind a mobile credential to a user’s device in Virtual Keypad. Step 6 (End User): Use the credential at the SR3 Bluetooth Reader. This guide walks you through all 6 steps. What’s Included What You’ll Need ▶ Drill ▶ If mounting with wall anchors, a 5/16” (8.0 mm) drill bit ▶ If mounting without wall anchors, a 5/64” (2.0 mm) drill bit ▶ #1 Phillips screwdriver ▶ #2 Phillips screwdriver ▶ Pliers ▶ Wire connectors ▶ Electrical tape Full Installation Guide To view the full SR3 Installation Guide (LT-2505), scan this QR code or visit DMP.com. This quick start guide walks you through Step 1 and Step 2. For the full installation guide, follow the QR code below.

SR3 Bluetooth and Proximity Reader Quick Start Guide Wire the Reader WARNING: Do not press and hold the button on the back of the reader. This procedure clears the unit’s memory and firmware, which renders the device inoperable until it is reconfigured and re-enrolled. Disconnect power before wiring the reader. After wiring and reconnecting power, the LED turns steady yellow, indicating that the reader is ready for enrollment. Follow these guidelines when wiring the reader: Connections must be made in accordance with NFPA 70: Do not connect to a receptacle controlled by a switch. Minimum wire gauge is 24 AWG with a maximum single wire run length of 500 ft (150 m). Caution: Do not cut the braided directional antenna wire. Wrap it around and secure it to the wiring harness for future use. WIRE COLOR PURPOSE TYPICAL X1 SERIES TERMINALS TYPICAL 734 SERIES TERMINALS TYPICAL KEYPAD WIRES Red Power (Positive) R1 RED Red Black Ground (Negative) B1 BLK Black White Data 1 W1 WHT White Green Data 0 G1 GRN Green/White Blue Green LED LC LC None Orange Beeper* (optional) BC RA None Purple Red LED (optional) None None None Yellow Smart Card Present (optional) None None None Copper, braided - Do not cut Directional Antenna (optional) None - Do Not Cut None - Do Not Cut None - Do Not Cut * If connected, the orange wire (beeper) mimics keypad beeping. Table 1:  Wire Connections SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand reader protocol to communicate with door controllers or access control modules. Procedure The installation must follow this procedure: Step 1 (Technician): Install the reader. Step 2 (Technician): Enroll and associate the reader with a system in Tech APP. Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin. Step 4 (Customer): Assign credentials to a user in Virtual Keypad. Step 5 (End User): Bind a mobile credential to a user’s device in Virtual Keypad. Step 6 (End User): Use the credential at the SR3 Bluetooth Reader. Full Installation Guide To view the full SR3 Installation Guide (LT-2505), scan this QR code or visit DMP.com. This quick start guide walks you through Step 1 and Step 2. For the full installation guide, follow the QR code below.