Draper Envoy Manuals

Copyright © 2014 Draper Inc. Form Envoy_Inst14 Printed in U.S.A. Installation/Operating Instructions Envoy Electric Projection Screen by Draper Hanging Screen General: When locating viewing surface and checking clearance for screen’s operation, remember surface is centered in case. Screen is normally recessed above ceiling and may be installed in a varie ty of ways. See typical installation detailed on page 2. Regardless of mounting method used, the following points apply: 1 Screen should be lifted into position only by the end mounting brackets. Keep case level by lifting end plates simultaneously to prevent surface damage. Draper provides eyebolts to use in hoisting the screen. Never attempt to lift screen along its length. 2 Screen should be positively and securely supported so that vibration or even abusive pulling on viewing surface will not weaken installation. 3 Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen. 4 Entire bottom of case must be readily accessible after installation is complete. 5 Hinge on bottom board and particularly hinge on automatic trap door of screen must be permitted to operate freely. Front and back of case must be straight— not forced to warp or bow. Hinges must be free from mastic or paint buildup, and doors must be unobstructed by ceiling tiles. 6 Do not use screen case to support adjacent sections of ceiling. 7 If trim pieces must be attached to case, do not permit screws to pro trude through ¾" wall of case. Do not attach trim with nails. 8 If case is painted, slots around doors should be shielded to protect viewing surface from paint splatters or overspray. 9 Do not seal unit in ceiling until electrical connections have been made and screen has been operated successfully. Caution 1 Read instructions through completely before proceeding. 2 Follow instructions carefully. Installation contrary to instructions invalidates warranty. 3 Do not lift case in center. Lift the ends simultaneously to avoid damage to case and surface. 4 Before removing screen from crate, check for damage and to make sure all parts are included. 5 Entire bottom of screen case should be unobstructed to permit proper operation of automatic trap door, and access to bottom panel for making electrical connections or servicing. 6 Screen should be installed level (using a carpenter’s level). 7 Nothing should be fastened to screen dowel, viewing surface or auto matic trap door. 8 Operating switch(es) packed separately in screen carton. Do not discard with packing material. 9 Screen operates on 110-120V, 60 hz., 1.1 amp current draw. NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Electrical Connections Screen operates on 110-120V, 60 hz., 1.1 amp current draw. Duty Cycle: ON 28 seconds /OFF 4 minutes. Junction box is located just above bottom board near left end of screen. Bottom board is held closed with flathead screws and may be opened with a Phillips screwdriver. Automatic trap door is held shut by viewing surface and must not be forced open. Removal of junction box cover plate exposes red, black and white pigtail leads and green internal ground wire per wiring diagram attached. Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire connecting screen to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and wiring should comply with National and local electrical codes. All operating switches should be “off” before power is connected. Operation When screen is first operated, be cautious! If automatic trap door does not drop open immediately when switch is flipped “down”, return switch to “off” and free trap door and/or recheck electrical connections before proceeding. Cycle unit down and up several times to confirm satisfactory operation. 110-120V Single Station Control — 3-position up-off-down switch permits operation to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up. 110-120V Multiple Station Control—Switches are similar in appearance to 110-120v Single Station Control. Screen stops when switch is released and 11/4" 11/4" 21/4" 5/8" 2" 2" Ceiling grid and tile (by others) 79/16" ® may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully down or fully up. 24V Control — Three-button up-stop-down switches stop at any point desired, operate in any sequence. Factory adjusted limit switches automatically stop screen when fully down or fully up. Key Operated Switching — Two kinds of key-operated switches are optionally available with this unit. 1 The key-operated power supply switch controls power to the screen and switches. When it is “off”, the switches will not operate screen. Key may be removed from the switch in either “on” or “off” position. 2 A three-position key switch permits the screen to be operated directly by key. In this case, the screen’s operator must always have a key. RS232/Ethernet—Serial communication and network communication optionally available with wall switches, RF or IR remote. If you encounter any difficulties installing or servicing your Envoy screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142. Caution: Do not remove the roller assembly from the case unless neces- sary for repairs. If the roller assembly is removed, be sure motor is fully re-seated in the bracket, and re-secure it carefully with the motor retaining spring or retaining clip, whichever is provided (see diagram below). These instructions are meant as a guide only. They do not imply any responsibility on the part of the manufacturer for improper installation or faulty workmanship at the jobsite. Limit Adjustments Please Note: Screen limits are factory set for optimum performance of the screen. A procedure is outlined below for minor tweaks, but any adjustment of these limits may negatively affect the flatness of the screen surface and could also void the warranty. Please check with Draper prior to resetting screen limits. CAUTION: Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run too far up or too far down. CAUTION: Be sure all switches are in “off” position before adjusting limit switches. The motor limit screws are normally located on the audience left of screen roller. "DOWN" LIMIT ADJUSTMENT To Reduce Screen Drop 1 Raise screen surface about 1' above desired setting and turn off. 2 Turn the DOWN limit screw (White or (I)) clockwise (three screw turns = ½ roller revolution). 3 Test by running screen down and repeat steps 1 and 2 until desired position is reached. To Increase Screen Drop 1 Run screen to the down limit. 2 With the down switch on, turn the DOWN limit screw (White or (I)) limit screw counterclockwise (three screw turns = ½ roller revolution) to increase drop. 3 Test by running screen up about 1' and back down to new down limit. 4 Repeat steps 2 and 3 until desired position is reached. "UP" LIMIT ADJUSTMENT Screen is Running Too Far Up 1 Lower screen surface about 1' below desired setting and turn off. 2 Turn the UP limit screw (Yellow or (II)) clockwise (three screw turns = ½ roller revolution). 3 Test by running screen up. 4 Repeat steps 1 through 3 until desired position is reached. Screen Needs to Run Up More 1 Run screen down about 1' and turn off. 2 With the up switch on, turn the UP limit screw (Yellow or (II)) limit screw counterclockwise (three turns of screw = ½ roller revolution). 3 Repeat steps 1 and 2 until desired position is reached. CAUTION: Do NOT allow the dowel to wrap up over the roller when the screen is running up! This could damage the screen.

Installation/Operating Instructions 220V Envoy Electric Projection Screen by Draper Copyright © 2014 Draper Inc. Form Envoy220v_Inst14 Printed in U.S.A. Operation When screen is first operated, be cautious! If automatic trap door does not drop open immediately when switch is flipped “down”, return switch to “off” and free trap door and/or recheck electrical connections before proceeding. Cycle unit down and up several times to confirm satisfactory operation. 220V Single Station Control—3-position up-off-down switch permits opera- tion to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up. 220V Multiple Station Control (Not CE approved)—Switches are similar in appearance to 220V Single Station Control. Screen stops when switch is released and may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully down or fully up. 24V Control—Three-button up-stop-down switches stop at any point desired, operate in any sequence. Factory adjusted limit switches automatically stop screen when fully down or fully up. Installer should incorporate an all-pole disconnect in the fixed wiring. Key Operated Switching (Not CE approved)—Two kinds of key-operated switches are optionally available with this unit. 1 The key-operated power supply switch controls power to the screen and switches. When it is “off”, the switches will not operate screen. Key may be removed from the switch in either “on” or “off” position. 2 A three-position key switch permits the screen to be operated directly by key. In this case, the screen’s operator must always have a key. RS232/Ethernet—Serial communication and network communication optionally available with wall switches, RF or IR remote. Adjustments Please Note: Screen limits are factory set for optimum performance of the screen. A procedure is outlined below for minor tweaks, but any adjustment of these limits may negatively affect the flatness of the screen surface and could also void the warranty. Please check with Draper prior to resetting screen limits. CAUTION: Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run too far up or too far down. CAUTION: Be sure all switches are in “off” position before adjusting limit switches. Adjusting “fully up” position — “Up” limit switch, located immediately above left end of automatic trap door, is tripped as door closes. If door does not close fully, limit switch should be raised slightly. If door closes too tightly, switch should be lowered slightly. Remove steel plate attached to threaded neck of “up” limit switch by removing hex nut securing it. Removing plate exposes three Phillips head machine screws which hold limit switch bracket in place. Turning these screws clock- wise will raise limit switch; turning them counterclockwise will lower it. Raise switch only in quarter-turn increments. When operating properly auto- matic trap door should close gently and rest against but not press on rubber bumpers above it. Adjusting automatic door so that it closes too tightly will damage screen. Adjusting “fully down” position — “Down” stopping position may be adjusted by turning the white (or I) limit switch adjustment socket. The white (or I) socket is located on the left end of screen roller and is accessible to a screwdriver/Allen wrench (4mm or 5/32") when automatic trap door is open. Access is easier when bottom board is also open. (Do not adjust the yellow or II socket which is next to and in back of the white or I socket). Turning the white (or I) socket counterclockwise will allow the viewing surface to run far- ther down. Turning it clockwise will shorten the viewing surface, causing it to stop in a less extended position. At no time should viewing surface be unrolled enough to expose any part of screen roller. If you encounter any difficulties installing or servicing your Envoy screen, call your dealer or Draper, Inc. Spiceland, Indiana, USA, 765/987-7999 or fax 765/987-1689. Caution 1 Read instructions through completely before proceeding. 2 Follow instructions carefully. Installation contrary to instructions invali- dates warranty. 3 Do not lift case in center. Lift the ends simultaneously to avoid damage to case and surface. 4 Entire bottom of screen case should be unobstructed to permit proper operation of automatic trap door, and access to bottom panel for making electrical connections or servicing. 5 Screen should be installed level (using a carpenter’s level). 6 Nothing should be fastened to screen dowel, viewing surface or auto matic trap door. 7 Operating switch(es) packed separately in screen carton. Do not discard with packing material. 8 Screen operates on 220V AC, 50 Hz., 1 ph. current. These Installation/Operating Instructions are available in the official language of the country where you purchase the product. Please contact your distributor to request a copy. Vous pourriez demander les instructions d’installation et d’opération traduises dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à votre distributeur. Die Gebrauchsanweisung für Installation und Konstruktion sind in der offi- ziellen Sprache des Landes, indem Sie das Produkt gekauft haben, vorhan- den. Fragen Sie die jeweilige Verkaufs-Abteilung. Hanging Screen General: When locating viewing surface and checking clearance for screen’s opera- tion, remember surface is centered in case. Screen is normally recessed above ceiling and may be installed in a varie ty of ways. See typical installation detailed on back of this sheet. Regardless of mounting method used, the fol- lowing points apply: 1 Screen should be lifted into position only by the mounting brackets. Keep case level by lifting both ends simultaneously to prevent surface damage. Never attempt to lift screen along its length. 2 Screen should be positively and securely supported so that vibration or even abusive pulling on viewing surface will not weaken installation. 3 Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen. 4 Entire bottom of case must be readily accessible after installation is complete. 5 Hinge on bottom board and particularly hinge on automatic trap door of screen must be permitted to operate freely. Front and back of case must be straight—not forced to warp or bow. Hinges must be free from mastic or paint buildup, and doors must be unobstructed by ceiling tiles. 6 Do not use screen case to support adjacent sections of ceiling. 7 If trim pieces must be attached to case, do not permit screws to pro trude through 19 mm (¾") wall of case. Do not attach trim with nails. 8 If case is painted, slots around doors should be shielded to protect viewing surface from paint splatters or overspray. 9 Do not seal unit in ceiling until electrical connections have been made and screen has been operated successfully. Electrical Connections Screen operates on 220V AC, 50 Hz., 1 ph. current. .75 amp current draw. Duty Cycle: On 28 seconds/Off 4 minutes. Junction box is located just above bottom board near left end of screen. Bottom board is held closed with flathead screws and may be opened with a Phillips screwdriver/Allen wrench (4mm or 5/32"). Automatic trap door is held shut by viewing surface and must not be forced open. Junction box contains brown, black and blue pigtail leads and green internal ground wire, per wiring diagram on reverse. Screen is shipped with internal wiring complete and control switch(es) fully NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. boxed. Wire connecting screen to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and wiring should comply with National and local electrical codes. All operating switches should be “off” before power is connected. These instructions are meant as a guide only. They do not imply any responsibility on the part of the manufacturer for improper installation or faulty workmanship at the jobsite. Caution: Do not remove the roller assembly from the case unless neces- sary for repairs. If the roller assembly is removed, be sure motor is fully re-seated in the bracket, and re-secure it carefully with the motor retaining spring or retaining clip, whichever is provided (see diagram below).

Installation/Operating Instructions 220V Envoy Electric Projection Screen by Draper Copyright © 2013 Draper Inc. Form Envoy220v_Inst13 Printed in U.S.A. Operation When screen is first operated, be cautious! If automatic trap door does not drop open immediately when switch is flipped “down”, return switch to “off” and free trap door and/or recheck electrical connections before proceeding. Cycle unit down and up several times to confirm satisfactory operation. 220V Single Station Control—3-position up-off-down switch permits opera- tion to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up. 220V Multiple Station Control (Not CE approved)—Switches are similar in appearance to 220V Single Station Control. Screen stops when switch is released and may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully down or fully up. 24V Control—Three-button up-stop-down switches stop at any point desired, operate in any sequence. Factory adjusted limit switches automatically stop screen when fully down or fully up. Installer should incorporate an all-pole disconnect in the fixed wiring. Key Operated Switching (Not CE approved)—Two kinds of key-operated switches are optionally available with this unit. 1 The key-operated power supply switch controls power to the screen and switches. When it is “off”, the switches will not operate screen. Key may be removed from the switch in either “on” or “off” position. 2 A three-position key switch permits the screen to be operated directly by key. In this case, the screen’s operator must always have a key. RS232/Ethernet—Serial communication and network communication optionally available with wall switches, RF or IR remote. Adjustments Please Note: Screen limits are factory set for optimum performance of the screen. A procedure is outlined below for minor tweaks, but any adjustment of these limits may negatively affect the flatness of the screen surface and could also void the warranty. Please check with Draper prior to resetting screen limits. CAUTION: Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run too far up or too far down. CAUTION: Be sure all switches are in “off” position before adjusting limit switches. Adjusting “fully up” position — “Up” limit switch, located immediately above left end of automatic trap door, is tripped as door closes. If door does not close fully, limit switch should be raised slightly. If door closes too tightly, switch should be lowered slightly. Remove steel plate attached to threaded neck of “up” limit switch by removing hex nut securing it. Removing plate exposes three Phillips head machine screws which hold limit switch bracket in place. Turning these screws clock- wise will raise limit switch; turning them counterclockwise will lower it. Raise switch only in quarter-turn increments. When operating properly auto- matic trap door should close gently and rest against but not press on rubber bumpers above it. Adjusting automatic door so that it closes too tightly will damage screen. Adjusting “fully down” position — “Down” stopping position may be ad- justed by turning the white limit switch adjustment socket. The white socket is located on the left end of screen roller and is accessible to a screwdriver/Allen wrench (4mm or 5/32") when automatic trap door is open. Access is easier when bottom board is also open. (Do not adjust the yellow socket which is next to and in back of the white socket). Turning the white socket counter- clockwise will allow the viewing surface to run farther down. Turning it clock- wise will shorten the viewing surface, causing it to stop in a less extended position. At no time should viewing surface be unrolled enough to expose any part of screen roller. ® If you encounter any difficulties installing or servicing your Envoy screen, call your dealer or Draper, Inc. Spiceland, Indiana, USA, 765/987-7999 or fax 765/987-1689. Caution 1 Read instructions through completely before proceeding. 2 Follow instructions carefully. Installation contrary to instructions invali- dates warranty. 3 Do not lift case in center. Lift the ends simultaneously to avoid damage to case and surface. 4 Entire bottom of screen case should be unobstructed to permit proper operation of automatic trap door, and access to bottom panel for making electrical connections or servicing. 5 Screen should be installed level (using a carpenter’s level). 6 Nothing should be fastened to screen dowel, viewing surface or auto­matic trap door. 7 Operating switch(es) packed separately in screen carton. Do not discard with packing material. 8 Screen operates on 220V AC, 50 Hz., 1 ph. current. These Installation/Operating Instructions are available in the official language of the country where you purchase the product. Please contact your distributor to request a copy. Vous pourriez demander les instructions d’installation et d’opération traduises dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à votre distributeur. Die Gebrauchsanweisung für Installation und Konstruktion sind in der offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung. Hanging Screen General: When locating viewing surface and checking clearance for screen’s opera- tion, remember surface is centered in case. Screen is normally recessed above ceiling and may be installed in a varie­ty of ways. See typical installation detailed on back of this sheet. Regardless of mounting method used, the fol- lowing points apply: 1 Screen should be lifted into position only by the mounting brackets. Keep case level by lifting both ends simultaneously to prevent surface damage. Never attempt to lift screen along its length. 2 Screen should be positively and securely supported so that vibration or even abusive pulling on viewing surface will not weaken installation. 3 Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen. 4 Entire bottom of case must be readily accessible after installation is complete. 5 Hinge on bottom board and particularly hinge on automatic trap door of screen must be permitted to operate freely. Front and back of case must be straight—not forced to warp or bow. Hinges must be free from mastic or paint buildup, and doors must be unobstructed by ceiling tiles. 6 Do not use screen case to support adjacent sections of ceiling. 7 If trim pieces must be attached to case, do not permit screws to pro­trude through 19 mm (¾") wall of case. Do not attach trim with nails. 8 If case is painted, slots around doors should be shielded to protect viewing surface from paint splatters or overspray. 9 Do not seal unit in ceiling until electrical connections have been made and screen has been operated successfully. Electrical Connections Screen operates on 220V AC, 50 Hz., 1 ph. current. Junction box is located just above bottom board near left end of screen. Bottom board is held closed with flathead screws and may be opened with a Phillips screwdriver/Allen wrench (4mm or 5/32"). Automatic trap door is held shut by viewing surface and must not be forced open. Junction box contains brown, black and blue pigtail leads and green internal ground wire, per wiring diagram on reverse. NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire connecting screen to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and wiring should comply with National and local electrical codes. All operating switches should be “off” before power is connected. These instructions are meant as a guide only. They do not imply any responsibility on the part of the manufacturer for improper installation or faulty workmanship at the jobsite.

Copyright © 2000 Draper, Inc. Form Envoyi00R Printed in U.S.A. 411 S. Pearl St., Spiceland, IN 47385 USA ❚ 765-987-7999 ❚ fax 765-987-7142 e-mail [email protected] ❚ www.draperinc.com Installation/Operating Instructions Envoy Electric Projection Screen by Draper Hanging Screen General: When locating viewing surface and checking clearance for screen’s operation, remember surface is centered in case. Screen is normally recessed above ceiling and may be installed in a variety of ways. See typical installation detailed on back of this sheet. Regardless of mounting method used, the following points apply: ➀ Screen should be positively and securely supported so that vibration or even abusive pulling on viewing surface will not weaken installation. ➁ Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen. ➂ Entire bottom of case must be readily accessible after installation is complete. ➃ Hinge on bottom board and particularly hinge on automatic trap door of screen must be permitted to operate freely. Front and back of case must be straight—not forced to warp or bow. Hinges must be free from mastic or paint buildup, and doors must be unobstructed by ceiling tiles. ➄ Do not use screen case to support adjacent sections of ceiling. ➅ If trim pieces must be attached to case, do not permit screws to protrude through ¾" wall of case. Do not attach trim with nails. ➆ If case is painted, slots around doors should be shielded to protect viewing surface from paint splatters or overspray. ➇ Do not seal unit in ceiling unit electrical connections have been made and screen has been operated successfully. Caution ➀ Read instructions through completely before proceeding. ➁ Follow instructions carefully. Installation contrary to instructions invalidates warranty. ➂ Entire bottom of screen case should be unobstructed to permit proper operation of automatic trap door, and access to bottom panel for making electrical connections or servicing. ➃ Screen should be installed level (using a carpenter’s level). ➄ Nothing should be fastened to screen dowel, viewing surface or automatic trap door. ➅ Operating switch(es) packed separately in screen carton. Do not discard with packing material. ➆ Screen operates on 115 v., 60 hz. current. NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Electrical Connections Screen operates on 115 v., 60 hz. current. Junction box is located just above bottom board near left end of screen. Bottom board is held closed with flathead screws and may be opened with a Phillips screwdriver. (Automatic trap door is held shut by viewing surface and must not be forced open.) Removal of junction box cover plate exposes red, black and white pigtail leads and green internal ground wire per wiring diagram attached. Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire connecting screen to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and wiring should comply with National and local electrical codes. All operating switches should be “off” before power is connected. Operation When screen is first operated, be cautious! If automatic trap door does not drop open immediately when switch is flipped “down”, return switch to “off” and free trap door and/or recheck electrical connections before proceeding. Cycle unit down and up several times to confirm satisfactory operation. 115V Single Station Control — 3-position up-off-down switch permits operation to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up. 115V Multiple Station Control—Switches are similar in appearance to 115V Single Station Control. Screen stops when switch is released and may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully up or fully down. 24V Control — Three-button up-stop-down switches stop at any point desired, operate in any sequence. Factory adjusted limit switches automatically stop screen when fully up or fully down. Key Operated Switching — Two kinds of key-operated switches are optionally available with this unit. ➀ The key-operated power supply switch controls power to the screen and switches. When it is “off”, the switches will not operate screen. Key may be removed from the switch in either “on” or “off” position. ➁ A three-position key switch permits the screen to be operated directly by key. In this case, the screen’s operator must always have a key. Adjustments Screen has been factory set and should not normally require further adjustment. However, if you desire to change the “up” and “down” stopping positions, proceed as follows: CAUTION: Be sure all switches are in “off” position before adjusting limit switches. Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run too far up or too far down. Adjusting “fully up” position — “Up” limit switch, located immediately above left end of automatic trap door, is tripped as door closes. If door does not close fully, limit switch should be raised slightly. If door closes too tightly, switch should be lowered slightly. Remove steel plate attached to threaded neck of “up” limit switch by removing hex nut securing it. Removing plate exposes three Phillips head machine screws which hold limit switch bracket in place. Turning these screws clockwise will raise limit switch; turning them counterclockwise will lower it. Raise switch only in quarter-turn increments. When operating properly automatic trap door should close gently and rest against but not press on rubber bumpers above it. Adjusting automatic door so that it closes too tightly will damage screen. Adjusting “fully down” position — “Down” stopping position may be adjusted by turning the white limit switch adjustment socket. The white socket is located on the left end of screen roller and is accessible to a screwdriver/ Allen wrench (4mm or 5/32") when automatic trap door is open. Access is easier when bottom board is also open. (Do not adjust the yellow socket which is next to and in back of the white socket). Turning the white socket counterclockwise will allow viewing surface to run farther down. Turning it clockwise will shorten the viewing surface, stopping it in a less extended position. At no time should viewing surface be unrolled enough to expose any part of screen roller. If you encounter any difficulties installing or servicing your Envoy screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999, fax (765) 987-7142, or e-mail [email protected].

Copyright © 2015 Draper Inc. Form Envoy_Inst15 Printed in U.S.A. Installation/Operating Instructions Envoy Electric Projection Screen by Draper Hanging Screen General: When locating viewing surface and checking clearance for screen’s operation, remember surface is centered in case. Screen is normally recessed above ceiling and may be installed in a varie­ty of ways. See typical installation detailed on page 2. Regardless of mounting method used, the following points apply: 1 Screen should be lifted into position only by the end mounting brackets. Keep case level by lifting end plates simultaneously to prevent surface damage. Draper provides eyebolts to use in hoisting the screen. Never attempt to lift screen along its length. 2 Screen should be positively and securely supported so that vibration or even abusive pulling on viewing surface will not weaken installation. 3 Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen. 4 Entire bottom of case must be readily accessible after installation is complete. 5 Hinge on bottom board and particularly hinge on automatic trap door of screen must be permitted to operate freely. Front and back of case must be straight— not forced to warp or bow. Hinges must be free from mastic or paint buildup, and doors must be unobstructed by ceiling tiles. 6 Do not use screen case to support adjacent sections of ceiling. 7 If trim pieces must be attached to case, do not permit screws to pro­trude through ¾" wall of case. Do not attach trim with nails. 8 If case is painted, slots around doors should be shielded to protect viewing surface from paint splatters or overspray. 9 Do not seal unit in ceiling until electrical connections have been made and screen has been operated successfully. Caution 1 Read instructions through completely before proceeding. 2 Follow instructions carefully. Installation contrary to instructions invalidates warranty. 3 Do not lift case in center. Lift the ends simultaneously to avoid damage to case and surface. 4 Before removing screen from crate, check for damage and to make sure all parts are included. 5 Entire bottom of screen case should be unobstructed to permit proper operation of automatic trap door, and access to bottom panel for making electrical connections or servicing. 6 Screen should be installed level (using a carpenter’s level). 7 Nothing should be fastened to screen dowel, viewing surface or auto­matic trap door. 8 Operating switch(es) packed separately in screen carton. Do not discard with packing material. 9 Screen operates on 110-120V, 60 hz., 1.1 amp current draw. NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Electrical Connections Screen operates on 110-120V, 60 hz., 1.1 amp current draw. Duty Cycle: ON 28 seconds /OFF 4 minutes. Junction box is located just above bottom board near left end of screen. Bottom board is held closed with flathead screws and may be opened with a Phillips screwdriver. Automatic trap door is held shut by viewing surface and must not be forced open. Removal of junction box cover plate exposes red, black and white pigtail leads and green internal ground wire per wiring diagram attached. Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire connecting screen to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and wiring should comply with National and local electrical codes. All operating switches should be “off” before power is connected. Operation When screen is first operated, be cautious! If automatic trap door does not drop open immediately when switch is flipped “down”, return switch to “off” and free trap door and/or recheck electrical connections before proceeding. Cycle unit down and up several times to confirm satisfactory operation. 110-120V Single Station Control — 3-position up-off-down switch permits operation to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up. 110-120V Multiple Station Control—Switches are similar in appearance to 110-120v Single Station Control. Screen stops when switch is released and 11/4" 11/4" 21/4" 5/8" 2" 2" Ceiling grid and tile (by others) 79/16" may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully down or fully up. 24V Control — Three-button up-stop-down switches stop at any point desired, operate in any sequence. Factory adjusted limit switches automatically stop screen when fully down or fully up. Key Operated Switching — Two kinds of key-operated switches are optionally available with this unit. 1 The key-operated power supply switch controls power to the screen and switches. When it is “off”, the switches will not operate screen. Key may be removed from the switch in either “on” or “off” position. 2 A three-position key switch permits the screen to be operated directly by key. In this case, the screen’s operator must always have a key. RS232/Ethernet—Serial communication and network communication optionally available with wall switches, RF or IR remote. If you encounter any difficulties installing or servicing your Envoy screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142. Caution: Do not remove the roller assembly from the case unless neces- sary for repairs. If the roller assembly is removed, be sure motor is fully re-seated in the bracket, and re-secure it carefully with the motor retaining spring or retaining clip, whichever is provided (see diagram below). These instructions are meant as a guide only. They do not imply any responsibility on the part of the manufacturer for improper installation or faulty workmanship at the jobsite. Limit Adjustments Please Note: Screen limits are factory set for optimum performance of the screen. A procedure is outlined below for minor tweaks, but any adjustment of these limits may negatively affect the flatness of the screen surface and could also void the warranty. Please check with Draper prior to resetting screen limits. CAUTION: Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run too far up or too far down. CAUTION: Be sure all switches are in “off” position before adjusting limit switches. The motor limit screws are normally located on the audience left of screen roller. "Down" Limit Adjustment To Reduce Screen Drop 1 Raise screen surface about 1' above desired setting and turn off. 2 Turn the DOWN limit screw (White or (I)) clockwise (three screw turns = ½ roller revolution). 3 Test by running screen down and repeat steps 1 and 2 until desired position is reached. To Increase Screen Drop 1 Run screen to the down limit. 2 With the down switch on, turn the DOWN limit screw (White or (I)) limit screw counterclockwise (three screw turns = ½ roller revolution) to increase drop. 3 Test by running screen up about 1' and back down to new down limit. 4 Repeat steps 2 and 3 until desired position is reached. "Up" Limit Adjustment Screen is Running Too Far Up 1 Lower screen surface about 1' below desired setting and turn off. 2 Turn the UP limit screw (Yellow or (II)) clockwise (three screw turns = ½ roller revolution). 3 Test by running screen up. 4 Repeat steps 1 through 3 until desired position is reached. Screen Needs to Run Up More 1 Run screen down about 1' and turn off. 2 With the up switch on, turn the UP limit screw (Yellow or (II)) limit screw counterclockwise (three turns of screw = ½ roller revolution). 3 Repeat steps 1 and 2 until desired position is reached. CAUTION: Do NOT allow the dowel to wrap up over the roller when the screen is running up! This could damage the screen.

Copyright © 2002 Draper Inc. Form Envoy_Inst02 Printed in U.S.A. Installation/Operating Instructions Envoy Electric Projection Screen by Draper Hanging Screen General: When locating viewing surface and checking clearance for screen’s operation, remember surface is centered in case. Screen is normally recessed above ceiling and may be installed in a variety of ways. See typical installation detailed on back of this sheet. Regardless of mounting method used, the following points apply: ➀ Screen should be positively and securely supported so that vibration or even abusive pulling on viewing surface will not weaken installation. ➁ Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen. ➂ Entire bottom of case must be readily accessible after installation is complete. ➃ Hinge on bottom board and particularly hinge on automatic trap door of screen must be permitted to operate freely. Front and back of case must be straight—not forced to warp or bow. Hinges must be free from mastic or paint buildup, and doors must be unobstructed by ceiling tiles. ➄ Do not use screen case to support adjacent sections of ceiling. ➅ If trim pieces must be attached to case, do not permit screws to protrude through ¾" wall of case. Do not attach trim with nails. ➆ If case is painted, slots around doors should be shielded to protect viewing surface from paint splatters or overspray. ➇ Do not seal unit in ceiling unit electrical connections have been made and screen has been operated successfully. Caution ➀Read instructions through completely before proceeding. ➁Follow instructions carefully. Installation contrary to instructions invalidates warranty. ➂Entire bottom of screen case should be unobstructed to permit proper operation of automatic trap door, and access to bottom panel for making electrical connections or servicing. ➃Screen should be installed level (using a carpenter’s level). ➄Nothing should be fastened to screen dowel, viewing surface or automatic trap door. ➅Operating switch(es) packed separately in screen carton. Do not discard with packing material. ➆Screen operates on 110-120v, 60 hz. current. NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Electrical Connections Screen operates on 110-120v, 60 hz. current. Junction box is located just above bottom board near left end of screen. Bottom board is held closed with flathead screws and may be opened with a Phillips screwdriver. (Automatic trap door is held shut by viewing surface and must not be forced open.) Removal of junction box cover plate exposes red, black and white pigtail leads and green internal ground wire per wiring diagram attached. Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire connecting screen to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and wiring should comply with National and local electrical codes. All operating switches should be “off” before power is connected. Operation When screen is first operated, be cautious! If automatic trap door does not drop open immediately when switch is flipped “down”, return switch to “off” and free trap door and/or recheck electrical connections before proceeding. Cycle unit down and up several times to confirm satisfactory operation. 110-120v Single Station Control — 3-position up-off-down switch permits operation to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up. 110-120v Multiple Station Control—Switches are similar in appearance to 110-120v Single Station Control. Screen stops when switch is released and may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully up or fully down. 24v Control — Three-button up-stop-down switches stop at any point desired, operate in any sequence. Factory adjusted limit switches automatically stop screen when fully up or fully down. Key Operated Switching — Two kinds of key-operated switches are optionally available with this unit. ➀ The key-operated power supply switch controls power to the screen and switches. When it is “off”, the switches will not operate screen. Key may be removed from the switch in either “on” or “off” position. ➁ A three-position key switch permits the screen to be operated directly by key. In this case, the screen’s operator must always have a key. Adjustments Screen has been factory set and should not normally require further adjustment. However, if you desire to change the “up” and “down” stopping positions, proceed as follows: CAUTION: Be sure all switches are in “off” position before adjusting limit switches. Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run too far up or too far down. Adjusting “fully up” position — “Up” limit switch, located immediately above left end of automatic trap door, is tripped as door closes. If door does not close fully, limit switch should be raised slightly. If door closes too tightly, switch should be lowered slightly. Remove steel plate attached to threaded neck of “up” limit switch by removing hex nut securing it. Removing plate exposes three Phillips head machine screws which hold limit switch bracket in place. Turning these screws clockwise will raise limit switch; turning them counterclockwise will lower it. Raise switch only in quarter-turn increments. When operating properly automatic trap door should close gently and rest against but not press on rubber bumpers above it. Adjusting automatic door so that it closes too tightly will damage screen. Adjusting “fully down” position — “Down” stopping position may be adjusted by turning the white limit switch adjustment socket. The white socket is located on the left end of screen roller and is accessible to a screwdriver/ Allen wrench (4mm or 5/32") when automatic trap door is open. Access is easier when bottom board is also open. (Do not adjust the yellow socket which is next to and in back of the white socket). Turning the white socket counterclockwise will allow viewing surface to run farther down. Turning it clockwise will shorten the viewing surface, stopping it in a less extended position. At no time should viewing surface be unrolled enough to expose any part of screen roller. 11/4" 11/4" 21/4" 5/8" 2" 2" Ceiling tile and grid (by others) 79/16"