Flomec QS200 Manuals

Flomec QS200 Installation manual (8 pages)

• Identifier: id-1831100
• Brand: Flomec
• Device: Kitchen Appliances
• Type: Installation manual, PDF
• Key Aspects: Detailed Product Specifications, Product Comparisons with Competitors, Innovations in Design
• UPD Date: 08.04.2026
• Source File: 1891663.pdf
• Pages: 8
• Description: Operational manual for the Flomec QS200. The manual highlights operating modes, service instructions, cleaning instructions, user instructions.

Key Pages and Contents:

• INSTALLING QS200 METER INTO AN EXISTING TEE INSTALLATION (continued)

  Figure 11 Install New QS200 Insert FLOMEC Multi-Tool PIN HOLE ALIGNMENT - For easy pin install CLEAN LID GROOVE - Remove dirt, roots, debris Figure 10 Remove Old Insert From Tee with FLOMEC Multi-Tool PRY UP - To break a stuck

• Set K-factor and Offset per QS200 FLOW INSERT SELECTION CHART below (reference QS200 Data Sheet - FLOW INSERT

  SELECTION CHART - Download DATA SHEET HERE. These calibrations will be configured in the irrigation controller. NOTE: Most irrigation controllers will refer to devices as �

• QS200 WIRING INSTALLATION (Tee and Meter should be installed before splice connections)

  Make sure wiring is only done on low DC voltage (7.5 VDC to 36 VDC). Make sure to follow all of the Controller/Decoder manufacturer’s directions for electrical safety. Also, refer to the General Safety Inst

• Using the FLOMEC® Multi-Tool

  The multi-tool (see Figure 9) was designed exclusively for tee type meters that use an insertion type insert. It facilitates easier removal of the insert, whether from a QS200 meter or other brands of tee type insertion meters. It is especially useful when attemptin

Flomec QS200 Product owners manual (24 pages)

• Identifier: id-1286228
• Brand: Flomec
• Device: Measuring Instruments
• Type: Product owners manual, PDF
• Key Aspects: Testing Methods for the Device, Sustainability Initiatives
• UPD Date: 27.07.2026
• Source File: 1301474.pdf
• Pages: 24
• Description: Device technical manual for the Flomec QS200. This manual covers repair references, service procedures, functional overview.

Key Pages and Contents:

• REPAIR PARTS ILLUSTRATION FOR QS200

  TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED MAINTENANCE / REPAIR Do not return this product without prior approval from the GPI Customer Service Department. Due to strict government regulations, GPI cannot accept parts

• Below is a typical QS200 meter with labeled components. Familiarize

  yourself with the meter before installation. Figure 2 TEE QUICK RELEASE PIN INSERT ASSY. BLACK WIRE RED WI

• Install New or Replacement Insert Into Tee

  1. The Tee insert bore must be clean before installing the insert and the (2) black O-rings on the insert should be fully lubr

• The LEDs are the primary indicators of meter performance. Refer to

  the Operations Section for LED indicating functionality. 2. Entrained air is air bubbles suspe

Flomec QS200 Product owners manual (22 pages)

• Identifier: id-1789594
• Brand: Flomec
• Device: Measuring Instruments
• Type: Product owners manual, PDF
• Key Aspects: Tips for Best Performance, Common User Mistakes
• UPD Date: 17.08.2026
• Source File: 1750680.pdf
• Pages: 22
• Description: Practical operating guide for the Flomec QS200. The document highlights operating procedures and regulatory notices, operational guidelines, network configuration.

Key Pages and Contents:

• Install New or Replacement Insert Into Tee

  1. The Tee insert bore must be clean before installing the insert and the (2) black O-rings on the insert should be fully lubr

• Remove Old Insert From Tee

  1. Clean all dirt and debris away from the immediate area of the old insert and the top of the meter, then pull out the quick release pin from

• Strip insulation ¾ in. (19 mm).

  b. With wire ends even, insert wires into the connector and tighten until secure. c. Insert the connector all the way into th

• LINE PIPE SIZES

  1" PIPE 1 1/2" PIPE 2" PIPE 3" PIPE 4" PIPE 3.500 [3 1/2] Ø 4.500 [4 1/2] Ø Figure 12 17 www.Globa

Flomec QS200 Product owners manual (16 pages)

• Identifier: id-1831090
• Brand: Flomec
• Device: Measuring Instruments
• Type: Product owners manual, PDF
• Key Aspects: Device History and Development, Feedback and Improvement Suggestions
• UPD Date: 10.06.2026
• Source File: 1891673.pdf
• Pages: 16
• Description: Installation and operation manual for the Flomec QS200. The manual outlines system configuration and maintenance, installation steps, configuration options.

Key Pages and Contents:

• REPAIR PARTS LIST FOR QS200 SADDLE

  Part Number Description 146502-01 Kit, Saddle Gasket 146503-01 Kit, Clamps (6 Inch ASME Pipe) 146503-02 Kit, Clamps (6 Inch Tube) 146503-03 Kit, Clamps (8 Inch A

• GENERAL SAFETY INSTRUCTIONS

  IMPORTANT: It is your responsibility to: • Ensure that all equipment operators have access to adequate instructions concerning safe operating and maintenance procedures. This product is not appr

• Place the marked sleeve back into saddle, engaging the threaded studs to the depth

  marked. Twist the bottom nuts upward to bottom of sleeve flange, replace the two nuts removed earlier and tighten al

• 920913-01 Quick Start Guide (QS200 Saddle)

  (1) Sleeve (1) Saddle (sized specifically for your pipe O.D.) (1) Gasket (2) Band Clamps Hardware (1) Retention Pin (Quick Release) (1) Sensor (if ordered) (1) S

Flomec QS200 Product owners manual (20 pages)

• Identifier: id-2202831
• Brand: Flomec
• Device: Plumbing Product
• Type: Product owners manual, PDF
• Key Aspects: Compliance and Certification Information, Initial Setup Steps
• UPD Date: 10.07.2026
• Source File: 2084801.pdf
• Pages: 20
• Description: Stepwise user guide for the Flomec QS200. The document includes installation support, safety protocols, service contacts, shutdown procedures.

Key Pages and Contents:

• Step 3 – Mounting the sleeve:

  Remove the top two nuts and pull sleeve from saddle. Using a tape measure, measure the distance from the lip of the inside of pipe to the top of the saddle. Reference the asterisk in Figure 3. Figure 3 Transpose this measurement onto the sle

• K-FACTOR FREQUENCY VALUES

• Step 1 – Drilling hole:

  It is recommended that the saddle/sensor not be located on the very top or very bottom of the pipe. Ideal performance can be achieved with the saddle mounted at 2 to 4 o’clock or 8 to 10 o’clock. Hole should also be drilled perpendicular to the pipe cente

• Determining the K-factor:

  The K-factor value is needed to convert the sensor’s output pulsed into volume or rate data. The graphs located on the back of the Quick Start Guide show K-factor values for many versions of water lines. By knowing the line you are using or the inside diamete