Hanna Instruments HI 9210N Manuals

Hanna Instruments HI 9210N Instruction manual (21 pages)

• Identifier: id-646100
• Brand: Hanna Instruments
• Device: Measuring Instruments
• Type: Instruction manual, PDF
• Key Aspects: Network Configuration Instructions, Features Comparison Chart
• UPD Date: 18.07.2026
• Source File: 641958.pdf
• Pages: 21
• Description: Step-by-step guide for the Hanna Instruments HI 9210N. It provides technical information on device calibration, system configuration, wiring setup, warranty information.

Key Pages and Contents:

• Each meter is supplied complete with batteries.

  Remove the back cover, unwrap the batteries and install them while paying attention to polarity. HI 9023C, HI 9024C, HI 9025C: To prepare the instrument for use connect the pH electrode and the temperatur

• SPECIFICATIONS HI 9024C & HI 9025C

  SPECIFICATIONS HI 9024C & HI 9025C SPECIFICATIONS HI 9024C & HI 9025C SPECIFICATIONS HI 9024C & HI 9025C SPECIFICATIONS HI 9024C & HI 9025C HI 9024C HI 9025C Range 0.00 to 14.00 pH; 0.0 to 100.0°C — 0.0/±399.9 mV (ISE) — ±400/±1999 mV (ORP) Resolution 0.0

• ORP MEASUREMENTS (HI 9023C AND HI 9025C)

  To enter the "mV" mode (ORP or ISE), turn the instrument ON and press the RANGE key until the display changes to mV. To measure the mV of a solution simply sub- merge the ORP or ISE electrode tip (4cm/ 1½") into the sample to be tested. Allow a few minute

• HI 9023C only:

  To calibrate with manual temperature compensation, follow this procedure: • Disconnect the temperature probe and switch the instrument ON. • Press RANGE to select the temperature mode. • Place the pH electrode into the 7.01 buffer stir gent

Hanna Instruments HI 9210N Instruction manual (20 pages)

• Identifier: id-413397
• Brand: Hanna Instruments
• Device: Multimeter
• Type: Instruction manual, PDF
• Key Aspects: Practical Advice for Users, Common Issues and Solutions, FAQs on Installation
• UPD Date: 16.06.2026
• Source File: 391971.pdf
• Pages: 20
• Description: Complete device guide for the Hanna Instruments HI 9210N. The guide covers usage and component overview, functional overview, device instructions, maintenance procedures.

Key Pages and Contents:

• 1) Battery cover

  2) BNC electrode connector 3) Offset calibration trimmer 4) Slope calibration trimmer 5) Temperature setting trimmer 6) Mode indicator 7) Liquid Crystal Display 8) ON/OFF key to turn the meter on or off 9) pH/°C SET key to select pH measurement or for manual temperature setting R

• To take a pH measurement remove the elec-

  trode protective cap and simply submerge the tip (4cm/1½") of the electrode and the tem- perature probe (wherever applicable) into the sample to be tested. Turn the instrument ON and if necessary, press RANGE u

• 1) Electrode connector (BNC for HI 9023C and DIN for HI 9023CN)

  2) Temperature probe socket (HI 9023C only) 3) Liquid Crystal Display 4) CAL key to enter or exit calibration mode 5) CFM key to confirm calibration 6) Ï°C and Ð C C C C C keys for manual temperature setting (HI 9023C only) 7) ON/O

• Note: The electrode should be submerged

  approximately 4 cm (1½") into the solution with the temperature probe located as close to it as possible. • Select the second buffer value on the secondary display by pressing the Ï°C or ÐC C C C C key. • When the “READY” and “CON” symb

Hanna Instruments HI 9210N Instruction manual (7 pages)

• Identifier: id-413416
• Brand: Hanna Instruments
• Device: Multimeter
• Type: Instruction manual, PDF
• Key Aspects: Maintenance Reminder Alerts, Sustainability Initiatives, Case Studies of Successful Implementations
• UPD Date: 28.02.2026
• Source File: 391990.pdf
• Pages: 7
• Description: Device user manual for the Hanna Instruments HI 9210N. The document details configuration and error codes, safety precautions, error handling.

Key Pages and Contents:

• SALES AND TECHNICAL SERVICE CONTACTS

  Australia: Tel. (03) 9769.0666 • Fax (03) 9769.0699 China: Tel. (10) 88570068 • Fax (10) 88570060 Egypt: Tel. & Fax (02) 2758.683 Germany: Tel. (07851) 9129-0 • Fax (07851) 9129-99 Greece: Tel. (210) 823.5192 • Fax (210) 884.0210 I

• 1) Battery cover

  2) DIN connector for electrode 3) Offset calibration trimmer 4) Slope calibration trimmer 5) Temperature calibration trimmer 6) Mode indicator 7) Liquid Crystal Display 8) ON/OFF key, to turn the meter on or off 9) RANGE key, to visualize the temperature HI 9210N ATC pH METER ON

• For best accuracy, it is recommended to calibrate the instrument frequently.

  In addition a pH calibration should be performed: a) Whenever the pH electrode or the batteries are replaced b) At least once a month c) After testing aggressive chemicals d) When extreme accuracy is required PREPARATIO

• pH VALUES AT VARIOUS TEMPERATURES

  Temperature has an effect on pH. The calibration buffer solutions are affected by temperature changes to a lesser degree than normal solutions. For pH calibration, please refer to the following chart. For instance, if the buffer temperature is 25°C, the display