Hytorc Clicker Manuals

This torque wrench, as calibrated at the factory, is certified to meet the accuracy in specifications: ASME B107.14- 2004, GGG-W-686, Type 2, Class A Style 1, 2 and ISO 6789. Additionally, all wrenches are calibrated on a torque standard traceable to the National Institute of Standards and Technology (N.I.S.T.). HYTORC is an ISO 17025 accredited business. This equipment may contain hazardous materials which can be harmful to the environment. Do not dispose of this equipment as municipal waste. Return it to the distributor or a designated collection center. LOCATE YOUR NEAREST HYTORC REPRESENTATIVE: HYTORC.COM/WORLD HYTORC WORLD HEADQUARTERS 333 Route 17 North, Mahwah, NJ 07430 +201-512-9500 • 800-FOR-HYTORC THE HYTORC UNIVERSE IS MADE UP OF OVER 1,000 TRAINED BOLTING SPECIALISTS TO SUPPORT YOUR BOLTING NEEDS IN OVER 100 COUNTRIES. Clicker Wrench Basic Operations Manual 333 Route 17 N. Mahwah, NJ 07430 USA 800-FOR-HYTORC (800-367-4986) 201-512-9500 hytorc.com WRENCH Model Number Serial Number CERTIFICATION IMPORTANT ENVIRONMENTAL NOTES CONVERSION TABLE FOR YOUR PERMANENT FILE FROM TO MULTIPLY BY: lb.in. oz.in. 16 lb.in. lb.ft. .08333 lb.in. kg.cm. 1.1519 lb.in. kg.m. .011519 lb.in. Nm .113 lb.in. dNm 1.13 lb.ft. kg.m. .1382 lb.ft. Nm 1.356 Nm dNm 10 Nm kg.cm. 10.2 Nm kg.m. .102 oz.in. lb.in. .0625 lb.ft. lb.in. 12 kg.cm. lb.in. .8680 kg.m. lb.in. 86.80 Nm lb.in. 8.85 dNm lb.in. .885 kg.m. lb.ft. 7.233 N.m lb.ft. .7376 dNm Nm .10 kg.cm. Nm .09807 kg.m. Nm 9.807 PLEASE RECYCLE 04022020-PR-GUIDE-CLICKERWRENCH SAFETY MESSAGES ADJUSTMENT OF TORQUE SETTINGS MAINTENANCE AND SERVICE WARNING! Read all safety warnings designated by the -symbol and all instructions. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE. When using an extension or adapter (increasing the effective length of the torque wrench) the output torque value will change. To calculate the new torque output of the wrench, use the following formula below. A number of variables will affect the accuracy of the above calculation: • Length of adapter or extension • Length of wrench • Variations in hand position on wrench TA Torque exerted at end of adapter L Distance between square drive and hand position TW Wrench scale reading A Length of adapter or extension CAUTION – RATCHET HEAD! Ratchet mechanism may slip or break if dirty, mismatched; if worn parts are used; or if direction lever is not fully engaged. Ratchets that slip or break can cause injury. • An out of calibration torque wrench can cause part or tool breakage • Periodic re-calibration is necessary to maintain accuracy • Do not exceed rated torque as overtorquing can cause wrench or part failure • Do not use torque instrument to break fasteners loose • Do not use cheater extension on the handle to apply torque. • Broken or slipping tools can cause injury. 1. The torque wrench’s internal mechanism is permanently lubricated during assembly. Do not attempt to lubricate the internal mechanism. 2. Clean torque wrench by wiping. Do not immerse. 3. Store torque wrench in protective case at its lowest torque setting. Do not force handle below lowest setting. 4. For more information or support, please call your local HYTORC Representative or 1-800-FOR-HYTORC (1-800-367-4986), or please visit us at HYTORC.com. A. To unlock the handle, hold tube and pull lock ring back, allowing handle to turn clockwise (CW) or counter- clockwise (CCW). B. Set wrench to desired torque as follows: EXAMPLE: 64 ft.-lbs. 1. Keep slight rearward pull on lock ring during all adjustments 2. Line up thimble edge with the “60” graduation cross line, and “0” with the vertical line. Torque wrench is now set to 60 ft.-lbs. (See Figure 1 below.) 3. Turn handle and set thimble graduation to “4” on vertical line. Torque wrench is now set to 64 ft.-lbs. (See Figure 2 below.) All users and bystanders should always wear safety goggles. FIGURE 1 FIGURE 2 4. Lock handle by releasing back pressure on lock ring until it clicks and handle doesn’t turn. 5. To torque fastener, keep hand centered on the grip handle. Apply a slow and steady force in the desired direction until a click/impulse is heard or felt. Stop pulling and allow the torque wrench to reset. (See Figure 3 above right.) L Major Graduations Lock Ring Minor Graduations Grip Handle Thimble Edge Unlock to Set Torque USE OF EXTENSIONS AND ADAPTERS TW TA AA FIGURE 3 Apply Force RELEASE FORCE TO RESET