Kicker DXA250.4 Manuals

DXA AMPLIFIERS Owner’s Manual DXA125.2 Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE DXA.2 Benutzerhandbuch | Deutsch MONOVERSTÄRKER DER DXA.2-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE DXA.2 2014 DXA Stereo Amp Rev B.indd 1 8/2/2013 3:32:23 PM 2 DXA.2-SERIES AMPLIFIER OWNER’S MANUAL INSTALLATION Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er. Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the battery’s negative post and the vehicle chassis is recommended. PERFORMANCE Authorized KICKER Dealer: Purchase Date: Serial Number: Model: DXA125.2 RMS Power @ 14.4V, 4Ω stereo, ≤ 1% THD+N @ 14.4V, 2Ω stereo, ≤ 1% THD+N @ 14.4V, 4Ω mono, ≤ 1% THD+N 30 x 2 60 x 2 125 x 1 Length [in, cm] 8-1/8, 21 Height [in, cm] 2-3/8, 6 Width [in, cm] 7-3/16, 18 Frequency Response [Hz] 10Hz–20kHz Signal-to-noise Ratio [dB} >95, A-weighted, re: rated power Input Sensitivity Low Level: 125mV–5V High Level: 250mV–10V Electronic Crossover HI, LO or OFF; Variable 50–200Hz @ 12dB/Octave KickEQ™ Bass Boost Variable 0-12dB @ 40Hz Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use genuine KICKER accessories and wiring. MODEL: DXA125.2 2014 DXA Stereo Amp Rev B.indd 2 8/2/2013 3:32:27 PM 3 Model External Fuse (sold separately) Power/Ground Wire KICKER Wiring Kit DXA125.2 1 x 40 Ampere 8 Gauge PK8, ZCK84 Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it. 12V battery external fuse remote turn-on (see page 5) bare-metal chassis ground bare-metal chassis ground ≤18” (45cm) ≤24” (60cm) The DXA amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifi er using the KICKER KISL as shown (make sure you set the DXA amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Keep the audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle. source unit high-level speaker outputs to amplifi er shield + – core conductor KICKER KISL (optional) from source unit high- level speaker outputs OR to amplifi er 2014 DXA Stereo Amp Rev B.indd 3 8/2/2013 3:32:27 PM

DXA AMPLIFIERS Owner’s Manual DXA250.4 Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE DXA.4 Benutzerhandbuch | Deutsch MONOVERSTÄRKER DER DXA.4-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE DXA.4 2014 DXA 4-Channel Amps Rev A.indd 1 2014 DXA 4-Channel Amps Rev A.indd 1 8/2/2013 4:44:10 PM 8/2/2013 4:44:10 PM 2 DXA.4-SERIES AMPLIFIER OWNER’S MANUAL INSTALLATION Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er. Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the battery’s negative post and the vehicle chassis is recommended. PERFORMANCE Authorized KICKER Dealer: Purchase Date: Serial Number: Model: DXA250.4 RMS Power [Watts] @ 14.4V, 4Ω stereo, ≤ 1% THD+N @ 14.4V, 2Ω stereo, ≤ 1% THD+N @ 14.4V, 4Ω mono, ≤ 1% THD+N 30 x 4 60 x 4 125 x 2 Length [in, cm] 12-7/16, 32 Height [in, cm] 2-3/8, 6 Width [in, cm] 7-3/16, 18 Frequency Response [Hz] 10–20k Signal-to-Noise Ratio [dB] >95, A-weighted, re: rated power Input Sensitivity Low Level: 125mV–5V High Level: 250mV–10V Selectable Electronic Crossover HI, LO or OFF; Variable 50–200Hz @ 12dB/Octave KickEQ™ Bass Boost Variable 0–12dB @ 40Hz Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use genuine KICKER accessories and wiring. MODEL: DXA250.4 2014 DXA 4-Channel Amps Rev A.indd 2 2014 DXA 4-Channel Amps Rev A.indd 2 8/2/2013 4:44:13 PM 8/2/2013 4:44:13 PM 3 The DXA amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifi er using the KICKER KISL as shown (make sure you set the DXA amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Keep the audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle. Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it. source unit high-level speaker outputs to amplifi er shield + – core conductor KICKER KISL (optional) from source unit high- level speaker outputs OR to amplifi er POWER WIRING 12V battery external fuse remote turn-on (see page 6) bare-metal chassis ground bare-metal chassis ground ≤18” (45cm) ≤24” (60cm) Model External Fuse (sold separately) Power/Ground Wire KICKER Wiring Kit DXA250.4 1 x 60 Ampere 8 Gauge PK8, ZCK84 2014 DXA 4-Channel Amps Rev A.indd 3 2014 DXA 4-Channel Amps Rev A.indd 3 8/2/2013 4:44:13 PM 8/2/2013 4:44:13 PM 4 BRIDGED OPERATION (MONO) minimum impedance of 4 ohms FOUR CHANNEL OPERATION minimum impedance of 2 ohms per channel L L R R 2014 DXA 4-Channel Amps Rev A.indd 4 2014 DXA 4-Channel Amps Rev A.indd 4 8/2/2013 4:44:13 PM 8/2/2013 4:44:13 PM