KVM-TEC USBflex Manuals

Check out our Installation Channel: www.kvm-tec.com flex USB kvm-tec Quick Installation 6032 SET USBfl ex Fibra 6032L CPU/LOCAL 6032R CON/REMOTE flex kvm-tec First Aid kvm-tec Support [email protected] Phone: +43 2253 81912 - 30 USB no funciona ningún poder (sin LED) Compruebe los enchufes de red ¿Está bien el sumi- nistro de energía? Pruebe con otro extensor. Intente reprogramar el dispositivo con un programador JTAG. Contactar con el soporte de kvm-tec ¿Los dispositivos USB están conectados correctamente? ¿El cable USB está conectado al PC en el lado local? ¿Los dispositivos USB están conec- tados directamente al PC? Compruebe que las unidades locales y remotas tienen el mismo fi rmware. Reemplace el cable USB del PC al extensor local. si tiene más de un dispositivo, compruebe qué dispositivos están defectuosos sustituyendo las unidades Contactar con el soporte de kvm-tec Estaremos encantados de responder a sus preguntas sobre su instalación? Manual de descarga www.kvm-tec.com más kvm-tec Canal de instalación en nuestra página web personal +43 2253 81912 Update with USB-Stick Plug the USB stick with update fi le into USB Flex. 2. press the button on the back left (if PtP, the USB channel will be disconnected) ~ 4 sec 3. wait until LED fl ashes orange (USB stick is scanned for updates) ~ 10-20 sec 4. LED lights up specifi cally for 3 seconds LED red -> no update on stick found (remove stick and start at step 1) LED green -> Update found, ready to start 5. press button again 6. wait until the update is completed or an error occurs (for PtP local is updated fi rst) ~ 2-3 min (PtP ~ 5-6 min) While update is running, LED fl ashes green, if data is transferred or copied, LED fl ashes very fast. At the end of the update, the LED fl ashes orange 4 more times and then starts the reboot process (the Extender must not be disconnected from the power supply during this process!)

Check out our Installation Channel: www.kvm-tec.com flex USB flex kvm-tec Quick Installation 6032 SET USBfl ex Fiber 6032L CPU/LOCAL 6032R CON/REMOTE flex kvm-tec First Aid Your Extender.... USB is not working No Power (No LED) Check the powerplug Is the power supply ok? Try another Unit. Try reprogramming the Unit by using a JTAG programmer Contact kvm-tec support Are the USB Devices plugged in correctly? Is the USB cable on the Local side plug- ged into the PC? Are the USB Devices working directly on the PC? Check if local and remote Unit have the same fi rmware Replace the USB cable from PC to the Local Extender Check if the local or the remote Unit is causing the problem by swaping fi rst the local and than the remote Unit to another Unit Contact kvm-tec support kvm-tec Support [email protected] Phone: +43 2253 81912 - 30 Update with USB-Stick Plug the USB stick with update fi le into USB Flex. 2. press the button on the back left (if PtP, the USB channel will be disconnected) ~ 4 sec 3. wait until LED fl ashes orange (USB stick is scanned for updates) ~ 10-20 sec 4. LED lights up specifi cally for 3 seconds LED red -> no update on stick found (remove stick and start at step 1) LED green -> Update found, ready to start 5. press button again 6. wait until the update is completed or an error occurs (for PtP local is updated fi rst) ~ 2-3 min (PtP ~ 5-6 min) While update is running, LED fl ashes green, if data is transferred or copied, LED fl ashes very fast. At the end of the update, the LED fl ashes orange 4 more times and then starts the reboot process (the Extender must not be disconnected from the power supply during this process!)

Check out our Installation Channel: www.kvm-tec.com flex USB kvm-tec Quick Installation 6032 SET USBfl ex Fibre 6032L CPU/LOCAL 6032R CON/REMOTE flex kvm-tec First Aid kvm-tec Support [email protected] Phone: +43 2253 81912 - 30 Kontaktieren Sie kvm-tec support Pas d‘alimen- tation (Pas de LED) USB ne foncti- onne pas Vérifi ez le prise de courant L‘alimentation électrique est-elle correcte ? Essayez une autre unité. Essayez de repro- grammer l‘appareil à l‘aide d‘un program- mateur JTAG. Contacter le sup- port kvm-tec Est-ce que l‘USB Appareils branchés correctement ? Le câble USB côté local est-il branché sur le PC ? Les périphériques USB foncti- onnent-ils directe- ment sur le PC? Remplacez le câble USB du PC vers le prolonga- teur local. Vérifi er si l‘unité locale et l‘unité dis- tante ont le même micrologiciel. Vérifi ez si l‘unité locale ou distante est à l‘origine du problème en ch- angeant d‘abord l‘unité locale et ensuite l‘unité distante vers une autre unit Nous sommes à votre disposition pour répondre à vos questions concernant l‘installation? Téléchargement du manuel www.kvm-tec.com ou kvm-tec Canal d‘installation sur notre page d‘accueil personnellement +43 2253 81912 Update with USB-Stick Plug the USB stick with update fi le into USB Flex. 2. press the button on the back left (if PtP, the USB channel will be disconnected) ~ 4 sec 3. wait until LED fl ashes orange (USB stick is scanned for updates) ~ 10-20 sec 4. LED lights up specifi cally for 3 seconds LED red -> no update on stick found (remove stick and start at step 1) LED green -> Update found, ready to start 5. press button again 6. wait until the update is completed or an error occurs (for PtP local is updated fi rst) ~ 2-3 min (PtP ~ 5-6 min) While update is running, LED fl ashes green, if data is transferred or copied, LED fl ashes very fast. At the end of the update, the LED fl ashes orange 4 more times and then starts the reboot process (the Extender must not be disconnected from the power supply during this process!)

Check out our Installation Channel: www.kvm-tec.com flex USB kvm-tec Quick Installation 6031 SET USBfl ex 6031L CPU/LOCAL 6031R CON/REMOTE flex kvm-tec First Aid kvm-tec Support [email protected] Phone: +43 2253 81912 - 30 USB no funciona ningún poder (sin LED) Compruebe los enchufes de red ¿Está bien el sumi- nistro de energía? Pruebe con otro extensor. Intente reprogramar el dispositivo con un programador JTAG. Contactar con el soporte de kvm-tec ¿Los dispositivos USB están conectados correctamente? ¿El cable USB está conectado al PC en el lado local? ¿Los dispositivos USB están conec- tados directamente al PC? Compruebe que las unidades locales y remotas tienen el mismo fi rmware. Reemplace el cable USB del PC al extensor local. si tiene más de un dispositivo, compruebe qué dispositivos están defectuosos sustituyendo las unidades Contactar con el soporte de kvm-tec Estaremos encantados de responder a sus preguntas sobre su instalación? Manual de descarga www.kvm-tec.com más kvm-tec Canal de instalación en nuestra página web personal +43 2253 81912 Update with USB-Stick Plug the USB stick with update fi le into USB Flex. 2. press the button on the back left (if PtP, the USB channel will be disconnected) ~ 4 sec 3. wait until LED fl ashes orange (USB stick is scanned for updates) ~ 10-20 sec 4. LED lights up specifi cally for 3 seconds LED red -> no update on stick found (remove stick and start at step 1) LED green -> Update found, ready to start 5. press button again 6. wait until the update is completed or an error occurs (for PtP local is updated fi rst) ~ 2-3 min (PtP ~ 5-6 min) While update is running, LED fl ashes green, if data is transferred or copied, LED fl ashes very fast. At the end of the update, the LED fl ashes orange 4 more times and then starts the reboot process (the Extender must not be disconnected from the power supply during this process!)

Check out our Installation Channel: www.kvm-tec.com flex USB kvm-tec Quick Installation 6031 SET USBfl ex 6031L CPU/LOCAL 6031R CON/REMOTE flex kvm-tec First Aid Kontaktieren Sie kvm-tec support kvm-tec Support [email protected] Phone: +43 2253 81912 - 30 Pas d‘alimen- tation (Pas de LED) USB ne foncti- onne pas Vérifi ez le prise de courant L‘alimentation électrique est-elle correcte ? Essayez une autre unité. Essayez de repro- grammer l‘appareil à l‘aide d‘un program- mateur JTAG. Contacter le sup- port kvm-tec Est-ce que l‘USB Appareils branchés correctement ? Le câble USB côté local est-il branché sur le PC ? Les périphériques USB foncti- onnent-ils directe- ment sur le PC? Remplacez le câble USB du PC vers le prolonga- teur local. Vérifi er si l‘unité locale et l‘unité dis- tante ont le même micrologiciel. Vérifi ez si l‘unité locale ou distante est à l‘origine du problème en ch- angeant d‘abord l‘unité locale et ensuite l‘unité distante vers une autre unit Nous sommes à votre disposition pour répondre à vos questions concernant l‘installation? Téléchargement du manuel www.kvm-tec.com ou kvm-tec Canal d‘installation sur notre page d‘accueil personnellement +43 2253 81912 Update with USB-Stick Plug the USB stick with update fi le into USB Flex. 2. press the button on the back left (if PtP, the USB channel will be disconnected) ~ 4 sec 3. wait until LED fl ashes orange (USB stick is scanned for updates) ~ 10-20 sec 4. LED lights up specifi cally for 3 seconds LED red -> no update on stick found (remove stick and start at step 1) LED green -> Update found, ready to start 5. press button again 6. wait until the update is completed or an error occurs (for PtP local is updated fi rst) ~ 2-3 min (PtP ~ 5-6 min) While update is running, LED fl ashes green, if data is transferred or copied, LED fl ashes very fast. At the end of the update, the LED fl ashes orange 4 more times and then starts the reboot process (the Extender must not be disconnected from the power supply during this process!)

kvm-tec User manual 6031 SET USBflex single in Kupfer 6031L CPU/LOCAL 6031R CON/REMOTE 6032 SET USBflex single in Fiber 6032L CPU/LOCAL 6032R CON/REMOTE www.kvm-tec.com Check out our Installation Channel: connect collaborate communicate control kvm-tec = C 4 USB flex