ORiNG IGPS-9822DGP+ Manuals

Quick Installation Guide Version 1.0 Quick Installation Guide Introduction PRINTED ON RECYCLED PAPER i s m a n a g e d G i g a b i t E t h e r n e t s w i t c h w i t h I G P S - 9 8 2 2 D G P + 8x10/100/1000Base-T(X) P.S.E ports and 2x 100/1G/2.5GBase-X + 2x 1G/10GBase-X SFP ports. The switch support Ethernet Redundancy protocol, O-Ring (recovery time < 30ms) and MSTP (RSTP/STP compatible) can protect your mission-critical applications from network interruptions or temporary malfunctions with its fast recovery technology. IGPS-9822DGP+ also support Power over Ethernet, a system to transmit electrical power up to 30 watts, along with data, to remote devices over standard twisted-pair cable i n a n E t h e r n e t n e t w o r k . E a c h s w i t c h h a s I G P S - 9 8 2 2 D G P + 8x10/100/1000Base-T(X) P.S.E. (Power Sourcing Equipment) ports. P.S.E. is a device (switch or hub for instance) that will provide power in a PoE connection. And support wide operating temperature from -20 C to 60 C. o o IGPS-9822DGP+ can also be managed centralized and convenient by Open- Vision, Except the Web-based interface, Telnet and console (CLI) configuration. Therefore, the switch is one of the most reliable choice for highly-managed and Fiber Ethernet application.interfaces, Telnet and console (CLI). Preparation Before you begin installing the switch, make sure you have all of the package contents available and a PC with Microsoft Internet Explorer 6.0 or later, for using web-based system management tools. Elevated Operating Ambient: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. Safety & Warnings Dimension Panel Layouts 1. Power LED 2. PWR1 LED 3. PWR2 LED 4. R.M. status LED 5. Ring status LED 6. Fault LED 7. Console port 8. Reset button 9. Link/action LED for Gigabit PoE LAN ports Package Contents Contents DIN-rail Kit CD IGPS-9822DGP+ Pictures Number X 1 X 1 X 1 Front View Top Panel The device is shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance. QIG Console Cable X 2 X 1 X 1 Wall-mount Kit 11 7 1 2 3 4 5 6 Rear View 1 2 1 1. Wall-mount screw holes 2. Din-rail screw holes 2 1. Terminal blocks: PWR1, PWR2 (50-57V DC), Relay 2. Ground wire. 1 Installation Step 1: Slant the switch and screw the Din-rail kit onto the back of the switch, right in the middle of the back panel. Step 2: Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into the rail firmly. DIN-rail Installation Step 1: Screw the two pieces of wall-mount kits onto both ends of the rear panel of the switch. A total of six screws are required, as shown below. Step 2: Use the switch, with wall mount plates attached, as a guide to mark the correct locations of the four screws. Step 3: Insert screws through the round screw holes (the red arrow as below) on the sides or through the cross-shaped aperture (the green arrow as below) in the middle of the plate and fasten the screw to the wall with a screwdriver. Step 4: If the screw goes through the cross-shaped aperture, slide the switch down before tightening the screw. Wall-mounting Q I G 1907-2-29-IGPS9822DGP+-1.0 Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. 10. Gigabit PoE LAN port 11. PoE LED for Gigabit PoE LAN ports 12. 100/1G/2.5GBase-X SFP ports 13. Link/Act LED for SFP port (100Mbps/1Gbps/2.5Gbps) 14. 1G/10GBase-X SFP ports 15. Link/Act LED for SFP port (1Gbps/10Gbps) IGPS-9822GDP+ GIGABIT I N D U S T R I A L SWITCH PoE Industrial Managed PoE Gigabit Switch 8 10 12 13 Network Connection The switch provides standard Ethernet ports. According to the link type, the switch uses CAT 3, 4, 5, 5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable specifications. Cable Types and Specifications: Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45 1000BASE-T Cat. 5 / Cat. 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45 Reset PWR PWR1 PWR2 R.M Ring Fault Console IGPS-9822DGP+ LNK/ACT PoE G3 G1 10/100/1000T G7 G5 G4 G2 G8 G6 G9 100/1G/2.5G LNK/ACT G12 G11 1G/10G G10 LNK/ACT Unit =mm (Tolerance ±0.5mm) Reset PWR PWR1 PWR2 R.M Ring Fault Console IGPS-9822DGP+ LNK/ACT PoE G3 G1 10/100/1000T G7 G5 G4 G2 G8 G6 G9 100/1G/2.5G LNK/ACT G12 G11 1G/10G G10 LNK/ACT 9 14 15 Reset PWR PWR1 PWR2 R.M Ring Fault Console IGPS-9822DGP+ LNK/ACT PoE G3 G1 10/100/1000T G7 G5 G4 G2 G8 G6 G9 100/1G/2.5G LNK/ACT G12 G11 1G/10G G10 LNK/ACT IGPS-9822DGP+