ORiNG IGS-9080 Manuals

IGS-9080 PWR PWR1 PWR2 R.M Ring Fault 10/100/ 1000T G3 G4 G1 G2 G7 G8 G5 G6 Reset Quick Installation Guide Version 1.0 Quick Installation Guide Introduction PRINTED ON RECYCLED PAPER The is a managed industrial Ethernet switch with eight 10/100/1000Base-T(X) ports. The series consists of the and models to meet different application needs. The former supports IEEE 1588v2 clock synchronization while the latter does not. The switch supports Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over 250 units of connection) and MSTP (RSTP/STP compatible) to protect mission-critical applications from network interruptions or temporary malfunctions with fast recovery technology. With a wide operating temperature from -40 C to 70 C, the device can be managed centrally via ORing’s proprietary Open-Vision platform as well as via Web- based interfaces, Telnet, and console (CLI). The switch is one of the most reliable choices for highly-managed and fiber Ethernet applications. IGS-9080 series IGPS-9080 IGPS-9080-NP o o Preparation Before you begin installing the switch, make sure you have all of the package contents available and a PC with Microsoft Internet Explorer 6.0 or later, for using web-based system management tools. Elevated Operating Ambient: Reduced Air Flow: Mechanical Loading: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. Safety & Warnings Dimension Panel Layouts 11 1. Reset button 2. PWR status LED 3. PWR1 LED 4. PWR2 LED 5. R.M. status LED 6. Ring status LED 7. Faulty relay indicator 8. Console port 9. Port speed LED 10. Port link LED 11. Gigabit Ethernet ports Package Contents Contents DIN-rail Kit CD IGS-9080 / IGS-9080-NP Pictures Number X 1 X 1 X 1 Front View Top Panel The device is shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance. GIGABIT I N D U S T R I A L SWITCH Industrial Managed Gigabit Switch QIG Console Cable X 1 X 1 X 1 Wall-mount Kit 10 Rear View 1 2 1 1. Wall-mount screw holes 2. Din-rail screw holes 1. Terminal blocks: PWR1, PWR2 (12-48V DC), Relay 1 Installation Step 1: Step 2: Slant the switch and screw the Din-rail kit onto the back of the switch, right in the middle of the back panel. Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into the rail firmly. DIN-rail Installation Step 1: Step 2: Step 3: Screw the wall-mount kit onto the rear panel of the switch. A total of six screws are required, as shown below. Use the switch, with wall mount plates attached, as a guide to mark the correct locations of the four screws. Insert a screw head through the large parts of the keyhole-shaped apertures, and then slide the switch downwards. Tighten the screws for added stability. Wall-mounting IGS-9080 Series Q I G IGS-9080 1907-2-29-IGS9080-1.0 Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. 9 Network Connection The switch provides standard Ethernet ports. According to the link type, the switch uses CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable specifications. Cable Types and Specifications: Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45 1000BASE-T Cat. 5 / Cat. 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45 54.3 32.2 45.0 14.0 40.0 50.0 25.3 33.6 12.5 54.3 145.1 108.5 32.0 32.2 116.0 18.0 18.15 51.0 209.3 7.35 187.4 R2.5 R3.95 46.0 IGS-9080 PWR PWR1 PWR2 R.M Ring Fault 10/100/ 1000T G3 G4 G1 G2 G7 G8 G5 G6 Reset 8 2 3 4 5 6 7 1 IGS-9080 PWR PWR1 PWR2 R.M Ring Fault 10/100/ 1000T G3 G4 G1 G2 G7 G8 G5 G6 Reset

IIG GSS--99884444//99884488G GPPFF IInndduussttrriiaall M Maannaaggeedd EEtthheerrnneett SSw wiittcchh UUsseerr M Maannuuaall VVeerrssiioonn 33..00 FFeebb,, 22001133 wwwwww..oorriinngg--nneettwwoorrkkiinngg..ccoom m