Sealey STW290 Manuals

INSTRUCTIONS FOR: DIGITAL TORQUE ADAPTOR MODEL No: STW290  WARNING! DO NOT use the digital torque adaptor if damaged or thought to be faulty.  Ensure all workshop safety rules, regulations, and conditions are complied with when using this digital torque adaptor.  Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.  Keep children and unauthorised persons away from the working area.  After use clean with a soft dry cloth and store in a safe, dry, childproof location.  Keep the digital torque adaptor away from magnets.  DO NOT subject the digital torque adaptor to excessive force or shocks.  DO NOT drop or throw the digital torque adaptor.  DO NOT use digital torque adaptor unless you have been instructed in its use by a qualified person.  DO NOT leave the digital torque adaptor in any place exposed to excessive heat, humidity or direct sunlight.  DO NOT use organic solvents such as alcohol or thinners to clean the digital torque adaptor.  DO NOT submerge the digital torque adapter in water or any other liquid.  DO NOT disassemble the digital torque adaptor.  DO NOT exceed the permitted torque value for the digital torque adaptor.  To ensure accurate measurement periodic re-calibration is necessary. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. Specifications: Drive: 1/2” Accuracy: ±2% Memory: 50 Display resolution: 0.1 Display Range: 40-200 N-m (29.5-147.5lb-ft) Operation Mode: Peak/Trace Unit Selection: kg-cm, kg-m, lb-in, lb-ft, Nm Length: 75mm Width: 45mm Battery: 1 x CR2032 Battery Life: 55hrs (continuous operation) Operating Ambient Temperature: -10ºC - 60ºC (13.9ºF - 139.9ºF) Storage Temperature: -20ºC - 70ºC (-4ºF - 157.9ºF) Operating relative humidity:15 to 90% non-condensing Auto shut off: After 80 seconds of inactivity  WARNING! DO NOT press “Mem” and “power “ button together as this will enter the unit into Calibration Mode. 3.1 Power On (fig.2). 3.1.1 Attach the adaptor to a ratchet or breaker bar. 3.1.2 Press and release the "ON/OFF" button to turn the adaptor on. The LCD panel shows "Trace" or “PtoP”. 3.1.3 After 2 seconds the LCD panel show "0.00". 3.1.4 Tighten the nut or bolt. 3.1.5 The LCD displays the torque value measured. Note: If not used for 80 seconds the Digital Torque Adaptor will automatically shut off. 3.2 How to select "Unit" (fig.2). Press "Mem" and "Peak / Trace" button together and release to select different torque units. Note: When you change units the target setting will also be changed to the new units value. This Digital Torque Adaptor contains 5 unit selections. (kg-cm, kg-m, in-lb, ft-lb, N-m). 1. SAFETY INSTRUCTIONS 2. INTRODUCTION & SPECIFICATIONS 3. INSTRUCTIONS Designed for use with a ratchet or breaker bar. Ideal for work around the engine bay and the tightening of wheel nuts to factory specifications. Large LCD display with selectable readings in Nm, lb.ft, lb.in, kg-cm or kg-m and accurate to ±2% of stated capacity. Memory stores up to 50 readings and features auto shut off after 80 seconds. Supplied with certificate and storage case. fig.1 fig.2 ON/OFF Button Buzzer Speaker Torque Setting Buttons Memory Button Peak/ Trace Button STW290 Issue No: 1 - 06/02/09 all-guides com