Sealey VSe4779.V2 Manuals

2. INTRODUCTION & APPLICATION 3. OPeRATION 2.1 Introduction: Remove/Install rear axle mounting bushes in Ford Fiesta IV, Ka. Can be used in situ – no need to remove the rear trailing link assembly from vehicle. 2.2 Applications: Ford Fiesta IV, Ka-1996 onwards. breakdown of this procedure refer to the vehicle manufacturer’s service instructions, or a proprietary manual. 3.4 Thoroughly apply penetrating oil to each bush to aid extraction from the bush housing. 3.5 To extract the old bush, assemble the tool onto the bush as shown in Fig.2. Ensure that the screw rod (1) is well lubricated prior to assembly. Hold the retention nut (2) with a 24mm ring spanner. Using a ratchet wrench with a 24mm deep socket turn the nut on the force nut assembly (6) clockwise to drive the bush out of its housing.  WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.  DO NOT use tools if damaged.  Maintain tools in good and clean condition for best and safest performance.  Ensure that the vehicle which has been jacked up is adequately supported with axle stands.  Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.  Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.  DO NOT use the tool for purposes other than for which it is designed  DO NOT use the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.  DO NOT use an impact wrench with this tool.  When not in use, store tool in a safe, dry childproof area. IMPORTANT! These instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions or a propriety manual, to establish the current procedure and data. WARNING: The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator. 1. SAFeTY INSTRUCTIONS ITem DeSCRIPTION 1 SCREW ROD 2 RETENTION NUT 3 PUSHING CUP ITem DeSCRIPTION 4 RECEIVING CUP 5 INSERTION CUP 6 FORCE NUT Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLeASe ReAD THeSe INSTRUCTIONS CAReFULLY. NOTe THe SAFe OPeRATIONAL ReQUIRemeNTS, WARNINGS AND CAUTIONS. USe THe PRODUCT CORReCTLY AND WITH CARe FOR THe PURPOSe FOR WHICH IT IS INTeNDeD. FAILURe TO DO SO mAY CAUSe DAmAGe AND/OR PeRSONAL INJURY, AND WILL INVALIDATe THe WARRANTY. PLeASe KeeP INSTRUCTIONS SAFe FOR FUTURe USe. Fig.1 Fig.2 Fig.3 3.6 To insert the new bush, assemble the tool and bush onto the bush housing as shown in Fig.3. Ensure that the screw rod (1) is well lubricated prior to assembly. Hold the retention nut (2) with a 24mm ring spanner. Using a ratchet wrench with a 24mm deep socket turn the nut on the force nut assembly (6) clockwise to drive the bush into the housing. DO NOT use AN IMPAcT wReNch wITh ThIs TOOl. 3.1 Before working under the vehicle ensure that it is adequately supported. 3.2 Thoroughly lubricate the screw rod threads each time the tool is used. 3.3 Remove the rear wheels to gain access to the bush housings at the top of each trailing arm. For a detailed and up to date Original Language Version VSE4779.V2 Issue: 1 - 24/11/11 INSTRUCTIONS FOR: ReAR AXLe BUSH TOOL - FORD FIeSTA IV, Ka Model No: VSe4779.V2