Serialio Scanfob 2002 Manuals

Visit http://serialio.com/support/Scanner/Scanfob_2002 for more information. Setup for connecting Scanfob® 2002 via Bluetooth as a Keyboard* Using iPad, iPhone, iTouch? Use this page. To use with SerialMagic or SerialMagic Gears, use the other side of this sheet. Step 1: Connect Scanfob® 2002 to powered USB port for about 4 hours Watch iPad/iPhone video http://youtu.be/RGNDsYWBAyw Step 2: Scan Keyboard-HID code to set the Scanfob® 2002 to keyboard mode. Keyboard - HID Step 3: Scan the "Make Discoverable & Connectable" code below or press the small button on the Scanfob® 2002 for five seconds, and the LED will rapidly flash blue. _+-DSCO-+_ Make Discoverable & Connectable Step 4: Start Bluetooth discovery from the Phone/PC and pick the Scanfob ® scanner when the "Scanfob..." name is shown on the Phone/PC. Step 5: The Scanfob® 2002 will begin beeping, the red scan beam will remain on, and the phone/PC will display some numbers. Scan the number barcodes to the right in the order presented by the phone or PC, then Scan the END barcode when done and the Scanfob® 2002 should beep, and the LED will slowly flash blue showing a good Bluetooth connection. If a mistake is made scanning, scan End, and go back to Step 4. Step 6: Scan one of the following codes as appropriate iOS/Windows OS X (prefix=NONE, suffix=CR) (prefix=NONE, suffix=ENTER) Step 7 (optional): For iPad/iPhone/iPod Touch, scan “Enable iOS Keyboard Toggle” below (only need to scan once). Press the small button on the Scanfob® 2002 to toggle the on-screen keyboard. _+-IOSON-+_ Enable iOS Keyboard Toggle When done using the Scanfob® 2002 scan the "Disconnect and Radio Off" code below or hold the small button for 5 seconds. To reconnect scan "Reconnect to Last Device" below or hold the big button for 5 seconds. The following codes are handy for disconnecting and reconnecting the Scanfob 2002. _+-DISC-+_ _+-CONN-+_ Disconnect and Radio Off Reconnect to Last Device 1 _Q1_ 2 _Q2_ 3 _Q3_ 4 _Q4_ 5 _Q5_ 6 _Q6_ 7 _Q7_ 8 _Q8_ 9 _Q9_ 0 _Q0_ END _ZZ_ Visit http://serialio.com/support/Scanner/Scanfob_2002 for more information. Setting up Scanfob® 2002 via Bluetooth with SerialMagic* Using iPad, iPhone, iTouch? Use other side of this sheet. Step 1: Connect Scanfob® 2002 to powered USB port for about 4 hours Step 2: Scan the SerialMagic-SPP code below to setup the Scanfob® 2002 for use with SerialMagic. SerialMagic - SPP Step 3: Launch SerialMagic app and do setup per your platform. Please find information at http://serialio.com/support/SerialMagic/index.php Step 4: When SerialMagic app is looking for the Scanfob® 2002 scan "Make Discoverable & Connectable" or press the small button on the Scanfob® 2002 for five seconds. The LED will flash blue rapidly. _+-DSCO-+_ Make Discoverable & Connectable Step 5: Pair the Scanfob® 2002 with your Phone or PC using SerialMagic software (see SerialMagic documentation for more information). The default Bluetooth PIN code for the Scanfob is 0000. Step 6: Scan the following code (prefix=STX, suffix=CR) Note: To reconnect the Scanfob® 2002 to the Phone or PC after it has been setup, follow Step 2 above. A slow blue flash of the LED shows a good Scanfob® 2002 Bluetooth connection to your PC or Phone. *SerialMagic software will post scans from the Scanfob® 2002 to virtually any application on your Android, BlackBerry, Windows Mobile, Symbian S60, Windows, & OS X. If you did not purchase SerialMagic software with your Scanfob® 2002, you can download a trial version here: http://serialio.com/products/SerialMagic/SmSuppPlat.php Scanfob 2002 Beep OFF Scanfob 2002 Beep ON The following codes are handy for disconnecting and reconnecting the Scanfob 2002. _+-DISC-+_ _+-DSCO-+_ Disconnect and Radio Off Reconnect SerialMagic For additional beeper settings see the URL at the bottom of this page