Sunstream Swiftshield A Series Manuals
Sunstream Swiftshield A Series Assembly, installation and use manual (48 pages)
- Identifier: id-1429788
- Brand: Sunstream
- Device: Lifting Systems
- Type: Assembly, installation and use manual, PDF
- Key Aspects: Environmental Considerations, Software Installation Instructions, Limitations of the Device
- UPD Date: 20.05.2026
- Source File: 1568656.pdf
- Pages: 48
- Description: Technical operation manual for the Sunstream Swiftshield A Series. It offers details on service procedures, technical specifications, setup guidelines.
Key Pages and Contents:
-
FORM NO. 660843 REV. B
PAGE 9 1-C Inserting the Bow Sprit forward tube Bolt SS 3/8-16 X 3.5” Nut SS Nylok 3/8-16 Steps: 1. Insert bow sprit extension into bow sprit. 2. Apply anti-seize to bolt threads before installing nut. 3. Final length to be determined after roller has been installed. Bow Sp -
FORM NO. 660843 REV. B
PAGE 40 11. For wind storms cover can remain wrapped on roller, store roller with cover in a dry location. 12. For cover repair or maintenance, un-wrap cover from roller and slide bead from track. 4-A Removing the Cover 9. Remove two nuts holding the ratcheting “shark fin� -
FORM NO. 660843 REV. B
PAGE 28 Steps: 1. Apply anti-seize to all screw threads before installing nuts. 2. Attach elbow to inside of starboard fin plate with screws, washers and nuts as shown. 3. Slide straight pipe over end of elbow on starboard side as shown*. 4. Insert second elbow on opposite en -
FORM NO. 660843 REV. B
PAGE 20 2-I Adjusting Arm Length Steps: 1. From dock, manually actuate arm back and forth to determine optimal length of arm and position of cylinder mount tube. 2. End of upper arm should extend 12” to 14” beyond the furthest point on the bow, includ- ing anchor, if equi
Sunstream Swiftshield A Series Assembly, installation and use manual (52 pages)
- Identifier: id-2247095
- Brand: Sunstream
- Device: Tent
- Type: Assembly, installation and use manual, PDF
- Key Aspects: Device History and Development, Industry Comparisons
- UPD Date: 03.06.2026
- Source File: 2040537.pdf
- Pages: 52
- Description: Owner’s manual for the Sunstream Swiftshield A Series. It outlines installation and wiring setup, backup procedures, safety features.
Key Pages and Contents:
-
FORM NO. 660769 REV. C PAGE 52
Warranty (Continued) SALT WATER REQUIREMENTS AND EXCLUSIONS: If any Company Product is used in brackish or salt water, the Pur -
FORM NO. 660769 REV. C
PAGE 10 Steps: 1. Locate rubber caps on solenoid. Slide back both upper and lower caps. 2. With 1/2” open end wrench, loosen nuts. 3. Re-position solenoid wire to the side. 4. Re-tighten nuts and slide rubber caps back. Before After 1-D Reposition Solenoid Wire 1. -
FORM NO. 660769 REV. C
PAGE 9 1-C Remove The PCFC (Pressure Compensated Flow Control) Steps: 1. Turn pump on side. 2. With 7/8” socket or adjustable wrench, unscrew hex cap. 3. With needle nose pliers, grab and remove PCFC. 4. Screw hex cap back onto pump. Note: You may set aside or discard, the -
FORM NO. 660769 REV. C
PAGE 33 2-Q Bow Sprit Installation Steps: 1. With boat raised, in the standard position on SunLift™. 2. Insert spreader pipe through hole in end of bow sprit extension tube, hold in place with cotter pins. 3. Apply anti-seize to all bolt threads before installing nuts. 4. P
Swiftshield A Series: Related Instructions from Other Manufacturers
-
NordicTrack NTSY9897.0 Home Gym Operation & user’s manual
20 -
Hyundai P240W Monitor Operation & user’s manual
23 -
Sharp R-654M Microwave Oven Operation manual with cookbook
48 -
Toyotomi FS1060A Air Conditioner Service manual
28 -
GRAUPNER MICRO STAR 190SX Game Instruction manual
44 -
Panasonic TY52LC16F1 - TELEVISION STAND-MULTI-LANG TV Accessories Instructions manual
14