X10 MS10A Manuals

Installation 1. Slide the battery compartment cover off and install four AA alkaline batteries. Observe polarity. 2. Set the slide switch on the back of the MS10A to 1 to trip the alarm if only one movement is detected (most sensitive). Set to 2 to trip the alarm only after 2 movements are detected (helps prevent false alarms). 3. Press the CODE button on the back of the MS10A with the point of a pencil. 4. Place the MS10A face down so that it can’t “see” any motion. (If it does it might install itself twice). 5. Set the INSTALL/RUN switch on your Security Console to INSTALL. 6. Press TEST on the MS10A. The Console beeps and the next unused zone indicator lights up. Motion Sensor, Model MS10A Set Up and Operating Instructions MS10A-8/02 The red light on the Motion Sensor blinks to indicate that it “saw you.” After you walk past the Motion Sensor, it will not see motion again for about 45 seconds (to conserve battery power). Wait about 45 seconds for the Motion Sensor to settle, arm the console in the Away mode, then walk past the Motion Sensor. The alarm trips and sounds its siren. Press disarm on your remote control. Replacing batteries Slide the battery compartment cover off and replace the batteries with four AA alkaline batteries. Observe polarity. After replacing the batteries, the following steps are necessary to determine that the Console still recognizes the Motion Sensor. 1. Place the Console’s slide switch to RUN1 or RUN2. 2. Press TEST on the Motion Sensor. If the appropriate zone indicator blinks, then the Console recognized the Motion Sensor and no further action is necessary. If the zone indicator didn't blink in step 2 above: 1. Place the Console’s slide switch to INSTALL. 2. Press TEST on the MS10A. The MS10A transmits a code to the Console. The console acknowledges this with a beep and logs in the MS10A. To make sure the Console logs the MS10A back into the same zone it was allocated to before you changed the batteries, wait four hours after removing the old batteries before reinstalling (until the appropriate zone indicator on the Console starts flashing). 7. Set the Console’s slide switch back to RUN1 or RUN2. 8. To set up additional Motion Sensors (up to 16*) repeat the above steps. *Note: you can install a total of 16 zones in the Console. This can be a combination of Door/Window Sensors and Motion Sensors. E.G. 8 Door/Window Sensors AND 8 Motion Sensors. See your Security System Owner’s Manual for more information. Operation When the Security System is armed using a Key Chain Remote (KR10A) the Motion Sensor will always trip the alarm when it sees motion. When the system is armed using an SH624 Remote Control it can be armed in the Home or Away mode. When armed in the Home mode, Motion Sensors will NOT trip the alarm. Place the Motion Sensor on a bookshelf, or attach it to a wall about 6 feet off the ground, using the supplied mounting bracket. Wait about 45 seconds for the Motion Sensor to settle then walk past it. X10.com, a Div. of X10 Wireless Technology, Inc. For additional help, visit www.x10.com/support F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. LIMITED 1-YEAR WARRANTY Please visit www.x10.com/warranty to complete your on-line warranty registration. Thank you. For help or more information on setup, please visit: www.x10.com/support TEST HIGH CODE LOW SENSITIVITY

Installation 1. Install four AA alkaline batteries in the battery compartment on the MS10A. Observe polarity. 4. Set the slide switch on the back of the MS10A to 1 to trip the alarm if only one movement is detected (most sensitive). Set to 2 to trip the alarm only after 2 movements are detected (helps prevent false alarms). 4. Press the CODE button on the back of the MS10A with the point of a pencil. 5. Set the INSTALL/RUN switch on the Security Console to INSTALL. 6. Press TEST on the MS10A. The Console emits a tone and the next unused zone indicator lights up. 7. Set the Console's slide switch back to RUN1 or RUN2. 8. To set up additional Motion Detectors (up to 16*) repeat the above steps. *Note: you can install a total of 16 zones in the Console. This can be a combination of Door/Window Sensors and Motion Detectors. E.G. 8 Door/Window Sensors AND 8 Motion Detectors. See your Security System Owner’s Manual for more information. Motion Detector, Model MS10A Set Up and Operating Instructions X-10 (USA) Inc., 91 Ruckman Rd., Closter, NJ 07624. http://www.x10.com MS10A-998DR If the Console is NOT armed and in the RUN2 mode, you will hear a chime. If the Console IS armed the Motion Detector will trip the alarm and sound the siren. After you walk past the Motion Detector, it will not see motion again for about a minute (conserves battery power). Replacing batteries Slide the battery compartment cover off and replace the battery with a 9V alkaline type. After replacing the battery, the following steps are necessary to determine that the Console still recognizes the MS10A. 1. Place the Console’s slide switch to RUN2. 2. Press TEST on the MS10A. If the Console chimes, it recognizes the MS10A and no further action is necessary. If the Console did not chime: 1. Place the Console’s slide switch to INSTALL. 2. Press TEST on the MS10A. The MS10A’s red indicator light flashes, and MS10A transmits a random code to the console. The Console acknowledges this with a beep and logs in the MS10A to the next available zone. To make sure the Console logs the MS10A back into the same zone it was allocated to before you changed the battery, wait 4 hours after removing the old battery before reinstalling (until the zone indicator on the Console starts flashing). X-10 (USA) INC. LIMITED 1-YEAR WARRANTY X-10 (USA) Inc. warrants X-10 products to be free from defective material and workmanship for a period of one (1) year from the original date of purchase at retail. X-10 (USA) Inc. agrees to repair or replace, at it’s sole discretion, a defective X-10 product if returned to X-10 (USA) Inc. within the warranty period and with proof of purchase. If service is required under this warranty: 1. Return the defective unit postage prepaid to X-10 (USA) Inc. at the address below. 2. Enclose a check for $4.00 to cover postage and handling. 3. Enclose a dated proof of purchase. 4. X-10 is not responsible for shipping damage. Operation When the Security System is armed using a Key Chain Remote the Motion Detector will always trip the alarm when it sees motion. When the system is armed using an SH624 Remote Control it can be armed in the Home or Away mode. When armed in the Home mode, Motion Detectors will NOT trip the alarm. Place the Motion Detector on a bookshelf, or attach it to a wall about 6 feet off the ground, using the supplied mounting bracket. Wait about 45 seconds for the Motion Detector to settle then walk past it. P.I.R MOTION DETECTOR