Emerson Oxymitter 5000 Instruction Manual

April 2001 2-6 Installation Rosemount Analytical Inc. A Division of Emerson Process Management Oxymitter 5000 NOTE: ALL MASONRY STACK WORK AND JOINTS EXCEPT ADAPTOR PLATE NOT FURNISHED BY ROSEMOUNT. INSTALLATION FOR MASONRY WALL STACK CONSTRUCTION INSTALLATION FOR METAL WALL STACK OR DUCT CONSTRUCTION 0.50 [13] 3.75 [95] MIN DIA HOLE IN WALL STACK OR DUCT METAL WALL MTG HOLES SHOWN ROTATED 45 OUT OF TRUE POSITION o WELD OR BOLT ADAPTOR PLATE TO METAL WALL OF STACK OR DUCT. JOINT MUST BE AIRTIGHT. 0.50 [13] 4.50 [114] O.D. REF PIPE 4.00 SCHED 40 PIP ...

April 2001 Rosemount Analytical Inc. A Division of Emerson Process Management Description and Specifications 1-1 Oxymitter 5000 SECTION 1 DESCRIPTION AND SPECIFICATIONS 1-1 COMPONENT CHECKLIST OF TYPICAL SYSTEM (PACKAGE CONTENTS) A typical Rosemount Oxymitter 5000 Oxygen Transmitter should contain the items shown in Figure 1-1. Record the part number, serial num- ber, and order number for each component of your system in the table located on the first page of this manual. Use the product matrix in Table 1-1 at the end of this section to compar ...

April 2001 Rosemount Analytical Inc. A Division of Emerson Process Management Installation 2-7 Oxymitter 5000 BRACE BARS (NOT BY ROSEMOUNT) 2.00 (51) NOTE: DIMENSIONS IN INCHES WITH MILLIMETERS IN PARETHESES. VERTICAL BRACE CLAMP ASSY. ABRASIVE SHIELD HORIZONTAL BRACE CLAMP ASSY. (BOTH BRACE CLAMP ASSEMBLIES ARE THE SAME. INSTALLATION AND LOCATION OF CLAMP ASSEMBLIES AND BRACE BARS TO BE DONE IN FIELD.) BY ROSEMOUNT } 2 HOLES - 0.625 (16) DIA FOR 0.50 (12) DIA BOLT 1.00 (25) MAX 0.375 (10) 1.00 (25) 4.12 (105) 4.12 (105) 60 MAX o 30 MIN o 5.62 (143 ...

April 2001 5-12 Troubleshooting Rosemount Analytical Inc. A Division of Emerson Process Management Oxymitter 5000 DIAGNOSTIC ALARMS TEST POINTS HEATER T/C HEATER O2 CELL CALIBRATION CALIBRATION RECOMMENDED O2 CELL mV + O2 CELL mv - HEATER T/C + HEATER T/C - INC INC DEC DEC HIGH GAS LOW GAS CAL TEST GAS + PROCESS - % O2 SW2 TP1 J1 TP2 TP3 RED YEL GRN ORG TP4 TP5 TP6 ON 28550022 Figure 5-10. Fault 10, High Cell mV j. Fault 10, High Cell mV The O2 CELL flashes once, pauses for three seconds, and repeats (Figure 5-10). 1. Using a multimeter, measure a ...

April 2001 5-8 Troubleshooting Rosemount Analytical Inc. A Division of Emerson Process Management Oxymitter 5000 DIAGNOSTIC ALARMS TEST POINTS HEATER T/C HEATER O2 CELL CALIBRATION CALIBRATION RECOMMENDED O2 CELL mV + O2 CELL mv - HEATER T/C + HEATER T/C - INC INC DEC DEC HIGH GAS LOW GAS CAL TEST GAS + PROCESS - % O2 SW2 TP1 J1 TP2 TP3 RED YEL GRN ORG TP4 TP5 TP6 ON 28550018 Figure 5-6. Fault 6, High High Heater Temp f. Fault 6, High High Heater Temp The HEATER LED flashes twice, pauses for three seconds, and repeats (Figure 5-6). 1. The high hig ...

April 2001 4-22 Maintenance and Service Rosemount Analytical Inc. A Division of Emerson Process Management Oxymitter 5000 6. Being careful not to disconnect the board wiring, carefully lift the board and spacer assembly from manifold (5) and set aside. Do not lose o-rings (8) from the bottom of spacers (9). 7. Tag and remove the leads from pres- sure switch (12). 8. Place a 1-1/16 in. 6-point socket over pressure switch (12) and remove. When installing the pressure switch, do not overtighten. Damage to the so- lenoid may occur. 9. Install new press ...