FLASHFORGE 3D PRINTER Hunter Operation & User’s Manual

62 Chapter 7: Supports and Service FlashForge team is on standby and ready to help you overcome any challenges you may have with your Hunter. If the issues or questions are not covered in this User Guide, you can seek for solutions on our official website or contact us via te ...

FLASHFORGE 3D PRINTER Hunter 40 Method 2: Click the [Rotate] icon on the left, and then enter into rotating angel values in X/Y/Z axes positioning. Click [Reset] to reset rotating angel values. 5.2.7 Scale Select the target object and scale the object by the following two methods: Method 1: Click the [Sc ...

FLASHFORGE 3D PRINTER Hunter 14 To filter used resin to prevent residue from affecting next printing.  Accessories Kits  Hexagon Wrench(2.5mm*1/3mm*1/4mm*1) Used to tighten or untighten screws when maintenance, please refer to flashforge support team before you take maintenance steps, for printer a ...

FLASHFORGE 3D PRINTER Hunter 47 5.2.11 File Menus ① New Project Click [File]--[New Project] can build a blank project. If there is an unsaved modification on previous project, then it will inform you whether the modification needs to be saved or not. Click [Yes] will save the modification, while click ...

FLASHFORGE 3D PRINTER Hunter 59 updating is completed. Please delete the three updating files from the USB stick on computer, to prevent interference with other functions of the USB stick. Method 2：Update via Internet Make sure power is not turned off during updating！ 1. Connect the Hunter printer to ...

FLASHFORGE 3D PRINTER Hunter 6 Notice Safety Notice ! Notices: Read all the instructions in the manual and familiarize yourself with the FlashForge Hunter User Guide before setting-up and using. Failure to comply with the warning and instructions may result in individual injury, fire, equipment damage or ...

FLASHFORGE 3D PRINTER Hunter 49 Method 1: Click [Edit]--[Redo] Method 2: Press the shortcut Ctrl+Y. ③Empty Undo-stack To clean up the recorded operating steps so as to release the memory. ④ Select All By the following two methods, you could select all models in the scene.(When models are too small to ...

19 6. (3-6)There is a carton box in each foam, eace holds a 500ml bottle of photopolymer resin, another includes a power adapter. 3-6 7. (3-7) Remove the plastic bag, the seal is on the bottom. 3-7 8. (3-8) Remove the clear protection film. 3-8 ...

FLASHFORGE 3D PRINTER Hunter 27 Wlan: Wlan: To open or close the wlan; Wlan list: To select available WiFi signal; Password: To enter the password; Finish: To connect to the WiFi signal; Back. Hotspot: Hotspot: To open or close the hotspot; SSID: To enter the hotpsot name; Password: To enter the hotspot ...

FLASHFORGE 3D PRINTER Hunter 54 6-3 (6-4) Click [Edit]-[Surface to platform], select on surface to contact the model and double click. After finished click [back] button, double click [Move] icon, then click [on platform]-[Center] icon. 图6-4 6-4 Note：If the model is in the correct position, there is ...

FLASHFORGE 3D PRINTER Hunter 26 4.3.2 Setting Settings: Printer Status: To show printer real-time status; WLAN: To turn on the WiFi; Hotspot: To turn on the hotspot; Z Move: To control the movement of Z-axis; Z Offset: To compensate the subtle movement of z-axis within ±1mm; Focusing: To adjust the foca ...

FLASHFORGE 3D PRINTER Hunter 41 5-4 ③Y Plane 5-5 ④Z Plane 5.2.9 Supports After loading the model, click [Edit]--[Supports] or click the Supports icon directly, then you will enter the support edit mode (5-7). Click [Back] to exit when you finish editing. 5-6 ...