Flomec EasyBatch Instruction Manual

1. PRESET 1.1 unit Unit -----(no unit); L; m3; kg; lb; GAL; USGAL; bbl 1.2 decs Decimals 0; 0.1; 0.02; 0.003 1.3 k-f K-Factor 0.000010 - 9999999 1.4 kf-d K-Factor Decimals 0; 0.1; 0.02; 0.003; 0.0004; 0.00005; 0.000006; 2. OVERUN 2.1 time Time 0 99 sec 2.2 Preclose 0000.000-9999999 3. METER 3.1 sign Signal Coil; Reed; NPN; PNP; N ...

Flomec EasyBatch The following keys are available: Fig. 2: Control panel Functions of the keys START-key This key is used to:  START the batch process.  to enter the preset value during programming.  to reset the total value.  gain access to SETUP-level; please read chapter 5. STOP-key This key is used to:  STOP / interrupt the ...

Flomec EasyBatch 1. Introduction ................................................................................................... 4 1.1 Product Overview.............................................................................................4 1.2 Specifications ........................................................................................ ...

Flomec EasyBatch Spare parts for your instrument are available from the local dealer or national distributor from whom you purchased the instrument; see spare parts list below to determine which parts numbers you require. Description: Includes: Part No: Bezel Cover 1 x Bezel Cover 1306014 Front Housing Kit Complete replacement front housing with facia. 1 ...

Flomec EasyBatch To enter programming mode, hold the START key down for 7 seconds until the SETUP indicator stops flashing. Once programming mode has been entered the STOP key can be used to cycle through the four sub-menu options and the START key can be used to view the screens within each sub-menu. When you wish to enter a screen to update a ...

Flomec EasyBatch By default, the EB11 will act at Operator level. For the Operator, the following functions are available:  To enter a batch quantity To change the PRESET-value, following procedure must be followed: 1) press START + STOP quickly and simultaneously: the word "PROG" will be flashing, If the buttons are held too long there will be no ...

Flomec EasyBatch IP66/67 Operating Temperature Range is -20oC ~ 60oC (-4oF ~ 140oF) LCD Display: Dimensions: 54 x 29mm (2.13” x 1.14”) 7 digit primary alpha-numeric LCD display with 12mm characters 7-digit secondary alpha-numeric LCD display with 7mm characters W ...

The EB11 is suitable for use with flowmeters which have a NPN output signal such as the hall effect output on the OM series flowmeter. The sensor supply (terminal 4) can power the electronics on OM series flowmeter PCBs. If the EB11 is ordered as the integral option for an OM series flowmeter, it will come in this configuration. 4.1 ...

Flomec EasyBatch The FLOMEC EB11 “Easy Batch” is a dual stage batch controller designed to create an efficient and accurate dispensing experience. Mountable either directly onto a FLOMEC flow meter or remotely, and compatible with multiple types of industry signals, the EB11 allows the user to control the volume of fluid dispensed i ...

Flomec EasyBatch All wiring connections should be made with good quality shielded instrument cable; wiring between terminals which are inside the instrument enclosure, or between a flowmeter and an integrally mounted instrument may use non-shielded wire. Cable shields or drain wires should be connected to the instrument ground (GND) at the instr ...

Flomec EasyBatch Mounting of the instrument on a pipe or flat surface (such as a wall) can be accomplished using the Wall Mount Kit (part no. 1522001) or Pipe Mount Kit (part no. 1522002) – see next page for diagram. 3.5 Panel Mounting Mounting of the instrument in a panel requires a 106mm (±2mm) / 4.10” - 4.25” round hole to be cut i ...