technetix AIMA-OPSW Product User Manual

Technetix Group Limited Product User Manual AIMA-OPSW 5.4 Module Installation 1. Gently depress the orange retaining clip and release the hinged tab Hinged tab Module fastening screw AIMA Module Orange retaining clip 2. Hold the AIMA module casing upright, align it with the AIMA3000 slide rails for the correct slot, and insert the module unt ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW Table 6-2 Modules Configuration Parameters Items Sub Items Effect and Configuration Method COnfiguration Module Information Model - - HW Assembly No. - - FW Version - - Serial No. - - FW Part No. - - Configuration Alarm Control Control Laser ON or OFF ON / OFF Alarm Settings Critical High ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW 3.4 Block Diagram 3.5 Order Details A-OPSW-[Y]-[Z] Optical A/B Protection Switch Options: Y Optical Connector Type S SC/APC* F FC/APC L LC/APC E E2000/APC Z Bandwidth 1G 45-1000 MHz Figure 3 1 OPSW Block Diagram *Standard option. Contact a PBN Sales Representative for availability of other ...

Technetix Group Limited Product User Manual AIMA-OPSW 6 Module Configuration & Alarms The module configuration settings can be configured using the web interface and Technetix NMSE (network management software). This manual only provides details on the web interface. For login details and network setup, please refer to the AIMA-ASMM user man ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW 6.3 Reboot The module can be rebooted remotely, shown in Figure 6-2 below. Detailed operations: Click the Modules tab, click the corresponding OPSW module, and click the Apply button in the commands section next to the word Reboot. Next, click on Submit to confirm then the module will aut ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW 6.2 Restoring Factory Defaults Loading factory default can restore the device to the factory default setting. Detailed operations: In the web interface, click the modules tab and click the module to be reconfigured on the left column of the interface (Figure 6-1). Click the Apply button i ...

Technetix Group Limited Product User Manual AIMA-OPSW 2. Then, pull the panel forward. 3. Then lift up the handle and slide the fi bre guide out of the front of the chassis. ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW 6.6 Input / Output Status Monitoring To setup Input / Output Status Monitoring, select the specific Port from the menu left on the left column, and the monitoring parameters are listed under Alarm Settings, check the boxes (☑) to toggle alarms. The page is shown in Figure 6-10 below. AI ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW 3.3 Specifications Optical Performance Optical wavelength 1270 ~ 1630 nm Optical input range -10 ~ +25 dBm Insertion loss with connectors 2 dB maximum Switch accuracy of optical < 0.5 dB Optical crosstalk 55 dB maximum Optical return loss 45 dB maximum Optical connector type SC/APC, FC/APC ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW 4.2 Technical Decription 4.2.1 Block Diagram Figure 4-4 OPSW Block Diagram Parameters Glossary OPT IN A also labeled InputB Optical input A OPT IN B also labeled InputA Optical input B OPT OUT Optical Output RF TP A RF A test port RF TP B RF B test port PD Detect A/B Amplifier Amplifier A ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW DO NOT remove the dust cap from the fi bre connector until right before connecting it to the input port. 4. Raise the clip, insert the fi bre connector, and then lower the clip over the connector. When using the sliding guide, put the fi bre connector in the clip and slide it in from the ...

technetix AIMA-OPSW Technetix Group Limited Product User Manual AIMA-OPSW 6.5.2 Module operating voltage and temperature alarm By clicking on the corresponding module, as shown in the following figure, the module's alarm information will appear. By clicking on OPSW under the Modules tab located in the top row, the operator can view the modules' temperatures and ...