Tascam HS-2 Owner's Manual

In this chapter, we explain the basic operation procedures that are the same in each operation mode. The display on this unit functions as a touchscreen. Operate the unit using its keys, switches and touchscreen display buttons. On every screen except the Home Screen, a button appears at the top left. Touch this button to return to the previ ...

NOTE You can also create the new AES31 file by touching CREATE AES31 button on the AES31 file selecting screen. 4 Touch the Enter button or press the DATA dial on the AES31 NAME screen. 5 Touch the OK button or press the DATA dial when the confirmation message appears on the pop-up window to create a new AES31 editing information file with ...

Tascam HS-2 1−Introduction Thank you very much for purchasing a TASCAM HS-2 2 Channel Audio Recorder. Please read this manual thoroughly before using the unit so that you understand correct operating procedures and can use its functions fully. We hope that you enjoy using this unit for many years. Please keep this manual so that you can read it at any t ...

Message Details and responses Remarks Cannot create new mark point. Mark point already exists at the same timestamp. You tried to create a mark at a time where a mark already ex­ ists. You cannot create a mark at the same time as another mark. Cannot create new project. Media Full. The media does not have enough space, so you cannot create ...

Tascam HS-2 Editing the playback starting time/ending point 1 Press the HOME key on the front panel to open the HOME screen. 2 Touch a file name or title name button display and then touch the ADJUST ENTRY button on the pull- down menu to open the ADJUST XXX screen. (“XXX” is the entry number.) NOTE You can also open this screen by touching the MEN ...

Tascam HS-2 Switching project screens When you press the ENTER button or a folder name (project name or session name) button on a project screen (project selection screen, session selection screen, AES31 file selection screen, take selection screen, playlist selection screen), a different screen will open as shown below. Project selection screen Session ...

Tascam HS-2 Combining takes (Combine) Combine a specified take with another one. NOTE You cannot combine takes in the following cases: • The bit length, the number of channels, sampling frequency, etc. are different. • The file size of the combined takes exceeds Max File Size shown on the REC SETUP/FILE FORMAT screens. • The capacity of the medi ...

Tascam HS-2 Sorting takes Sort the order of the played takes by name. 1 Touch the MENU button on the take selection screen to display the pull-up menu item. Take selection screen during the pull-up menu display 2 Touch the SORT button on the pull-up menu item to display the pop-up window for confirmation. Confirmation message screen 3 Touch the OK but ...

Tascam HS-2 Message Details and responses Remarks External Clock Regained Switch to External? Synchronization with an external clock became possible again. EXTERNAL Control Locked External control connectors are locked to prevent misopera­ tion. File Copy Failed. Failed to copy the file. Folder Copy Failed. Failed to copy the folder. --- FORMAT --- Com ...

Tascam HS-2 Auto Ready Turn the auto ready function ON or OFF (default). If auto ready is ON, when playback of a take completes the unit automatically stops at the beginning of the next take. This setting affects all modes except timeline mode. Inc. Play Turn the incremental play function ON or OFF (default). When incremental play is ON, press the PLAY k ...

Tascam HS-2 D-IN button: Synchronize with the clock of the digital signal selected as the input for DIGITAL IN. You cannot select an input as the master clock if the sampling rate converter is ON for that input. On the second line of the button, the digital input signal selected is shown. NOTE • A mark appears on the button of the currently active ma ...

Tascam HS-2 PARALLEL page Set the AUX 1-3 functions of the PARALLEL connector. AUX Assign Touch a knob to select it, making the background yellow, and turn the DATA dial to set the parameter. The parameters that can be selected include F.FWD, REW, MARK, MARK SKIP–, MARK SKIP+,and CALL. AUX1 Function: Set the function of PARALLEL connector pin 17 (AUX1) ...