Sharp XL-MP150 Operation Manual

4 Within 10 seconds, press the or button to se- lect "ONCE SET" or "DAILY SET", and press the MEMORY/ SET button. 5 Press the or button to select "PLAY" or "REC", and press the MEMORY/SET button. The illustrations show the daily timer setting. 6 Press the or button to adjust the hour and then press the MEMORY/SET button. The illustrations show the timer playback setting in the daily tim- er mode. 7 Press the or button to adjust the minutes and then press the MEMORY/SET button. 8 Set the time to finish as in steps 6 and 7 above. W ...

System connections RATED SPEAKER IMPEDANCE: 6 OHMS MIN. AC INPUT ANTENNA RIGHT RIGHT LEFT GND FM 75 OHMS AM LOOP VIDEO/AUX IN SUBWOOFER PRE-OUT SPEAKERS LEFT SPEAKERS LIGHT-UP LEFT RIGHT Left speaker Right speaker AC outlet (AC 120 V, 60 Hz) Speaker connection (see page 11) AM loop antenna FM antenna Make sure to unplug the AC power cord before any connections. Antenna connection (see page 11) AC power connection (see page 12) Speaker light-up wire Speaker light-up wire ...

Auto power on function: When you press any of the following buttons, the unit turns on. z TUNER (BAND) button (main unit and remote control): The unit turns on and the "TUNER" function is activated. z / button on the main unit: The unit turns on and playback of the last function starts (CD,TAPE,TUNER,VIDEO/AUX). „ Tuning Notes: z When radio interference occurs, auto scan tuning may stop auto- matically at that point. z Auto scan tuning will skip weak signal stations. z To stop the auto tuning, press the TUNING button again. To receive an FM stereo tr ...

„ Tape playback Auto power on function: When you press any of the following buttons, the unit turns on. z TAPE button (main unit and remote control): The unit turns on and the "TAPE" function is activated. z TAPE button on the remote control: The unit turns on and side A playback starts (regardless of the last function). z / button on the main unit: The unit turns on and playback of the last function starts (CD,TAPE,TUNER,VIDEO/AUX). Auto power off function: In the stop mode of tape operation, the main unit enters the stand-by mode aft ...

In this example, the clock is set for the 12-hour (AM 12:00) display. To confirm the time display: [When the unit is in the stand-by mode] Press the CLOCK/TIMER button. The time display will appear for about 10 seconds. [When the power is on] Press the CLOCK/TIMER button. Within 10 seconds, press the or button to display the time. The time display will appear for about 10 seconds. Note: The "CLOCK" will appear or time will flash to confirm the time dis- play when the AC power supply is restored after a power failure or unplugging the unit. I ...

Listening to a CD or MP3/WMA disc (continued) „ Various disc functions Notes for CD: Notes for MP3/WMA discs: z Track up/track down is possible only within individual discs. z The sound is heard during fast forward/fast reverse with a CD, but not with an MP3/WMA disc. For fast forward or fast reverse of an MP3/WMA disc, refer to playback time on the display. z Fast forward/fast reverse is possible only within individual tracks. z When the end of the track is reached during fast forward, the next track will be played. Playback of the track will begin whe ...

„ Programmed play You can choose up to 32 selections for playback in the order you like. To cancel the programmed play mode: While in the stop mode and the "MEMORY" indicator is lit, press the CLEAR/DIMMER button on the remote control. The "MEMORY" in- dicator will disappear and all the programmed contents will be cleared. Adding tracks to the program: If a program has been previously stored, the "MEMORY" indicator will be displayed. Then follow steps 1 - 6 to add tracks. The new tracks will be stored after the last track of the original program. To che ...