Integra DTR-5.5 Instruction Manual

]/[ ] buttons The FR [ ] button is used to start fast reverse. The FF [ ] button is used to start fast forward. N Stop [ ] button This button is used to stop playback. O Random button This button is used with the random playback func- tion. P Memory button This button is used with the memory playback func- tion, ...

—Continued Video Connections You only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the AV receiver’s V VIDEO 3 IN jack to a composite video output on your video source, as shown. ■ Using S-Video Use an S-Video cable to connect the AV receiver’s S VI ...

Integra DTR-5.5 component (VCR, etc) connected to the VIDEO 1 OUT or VIDEO 2 OUT. See pages 27–38 for information on connecting components. Recording Separate AV Sources Here you can record audio and video from completely separate sources, allowing you to overdub audio onto ...

Integra DTR-5.5 —Continued Advanced Controlling Other Components Entering a Remote Control Codes................................. 80 Learning Commands from Another Remote Controller ..................................................................... 88 Using Macros................................................................... 89 Advanced Setup D ...

Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in partic- ular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable ent ...

Integra DTR-5.5 —Continued The AV receiver has AC outlets on its rear panel that can be used to connect the power cords of AV other compo- nents that you intend to use with the AV receiver. These components can then be left turned on so that they turn on and off as and when the AV receiver is turned on and set to Standby. Caution: • Make su ...

Integra DTR-5.5 —Continued If you connect an -compatible Integra MiniDisc recorder or CD recorder to the TAPE IN/OUT jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. Changing the TAPE/MD/CDR Display 1 Press the [TAPE] input selector button so that “TAPE” appears on the display. 2 Press ...

Integra DTR-5.5 —Continued SAT (satellite receiver) Manufacturer Control code Tristar 4016 Unisat 4013 Universum 4021, 4024 Vortec 4017 Wela 4025 Zehnder 4020 Zenith 4032 CBL (cable receiver) Manufacturer Control code ABC 3001, 3002, 3021 Archer 3006 Cabletime 3028, 3032 Cableview 3004 Contec 3009 Eastern 3010 GE 3001, 3002 Gemini 3011 Gene ...

Integra DTR-5.5 In the following diagram, an IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver in the cabinet via the connecting block. • On the Remote Setup menu, set the IR IN Position set- ting to “Main” (see page 72). Controlling Out-of-range Components ...

Integra DTR-5.5 —Continued J OPTICAL DIGITAL (27, 28, 30, 32, 34, 35) The DTR-5.5 doesn’t have an IN 4 jack. The optical digital audio inputs can be used to con- nect CD and DVD players, and other components with an optical digital audio output. The optical output can be used to connect a CD recorder or other digital recorder with an optical digit ...

Integra DTR-5.5 —Continued The AV receiver is configured using onscreen setup menus, which are displayed on the TV that’s connected to either of the MONITOR OUT jacks. Because they appear on your TV, they’re large and clear, making setup a breeze. Settings are divided into two groups: Basic Setup and Advanced Setup . When you’ve configured the ...