Juniper JUNOSE 11.0.2 RELEASE NOTES Release Note

44 „ Known Problems and Limitations „ The E Series router IGMPv3 proxy does not operate correctly in the presence of IGMPv2 queriers. [Defect ID 46039/46045] Work-around: If an IGMPv2 router is present on the network, do not configure version 3 with the ip igmp-proxy version command on that network interface. (Version 2 is the d ...

Juniper JUNOSE 11.0.2 RELEASE NOTES „ 97 Appendix A: System Maximums Ethernet VLAN overriding profile assignments per chassis 200 200 Ethernet VRRP VRIDs per line module 800 800 HDLC interfaces per chassis 24,000 24,000 HDLC interfaces per line module 8000 8000 MLPPP bundles per chassis 12,000 12,000 MLPPP bundles per line module The maximum number of MLPPP bundl ...

Juniper JUNOSE 11.0.2 RELEASE NOTES 74 „ ERX310, ERX7xx, and ERX14xx System Maximums Link Layer Maximums Table 3 lists link layer maximums for the ERX routers. The following notes are referred to in Table 3: 1. The ERX1440 router supports a maximum of 48,000 interface columns of all types combined. You can use either all dynamic interfaces or a combination of dynam ...

Juniper JUNOSE 11.0.2 RELEASE NOTES 8 „ Early Field Trial Features Early Field Trial Features The features described in this section are present in the code but have not yet been fully qualified by Juniper Networks. These features are available only for field test purposes in this release. If you use any of these features before they have been fully qualified, it i ...

Juniper JUNOSE 11.0.2 RELEASE NOTES Networks E Series Broadband Services Routers and contain the following sections: „ Release Highlights on page 7 „ Early Field Trial Features on page 8 „ Unsupported Features on page 9 „ Release Software Protocols on page 1 ...

Juniper JUNOSE 11.0.2 RELEASE NOTES 102 „ E120 and E320 System Maximums Policy and QoS Maximums Table 12 lists policy and QoS maximums for the E120 router and the E320 router. The following notes are referred to in Table 12: 1. For more information about system resource requirements for nodes, queues, and shadow nodes, see JunosE Quality of Service Configuration Gu ...

supported in previous JunosE Software releases. As a result, If you are upgrading to the current JunosE release from a lower-numbered release, configurations that use CAC and bulk configuration on the same ATM interface continue to work. However, we reco ...

52 „ Known Problems and Limitations Stateful SRP Switchover (High Availability) and IP Tunnels „ A packet loss sometimes occurs during stateful SRP switchover when you use the ping command on a router that is configured for OSPF graceful restart, and is connected to a helper router in the OSPF IPv6 broadcast network and another ...

Juniper JUNOSE 11.0.2 RELEASE NOTES 28 „ Known Behavior MPLS „ Martini circuits configured on the ES2 10G LM act as true layer 2 tunnels, without modifying the layer 2 headers. For this reason, Martini VLAN retagging is not currently supported. „ If you are upgrading to Release 7.1.0 or a higher-numbered release from a release numbered lower than Release 7.1.0, a ...

Juniper JUNOSE 11.0.2 RELEASE NOTES 60 „ Errata Errata This section identifies errors found in the JunosE documentation. These errors are corrected in subsequent releases of the affected documentation. „ The Obtaining Documentation section in the About the Documentation chapter of every JunosE document erroneously indicates that MIBs are available on the JunosE So ...

Juniper JUNOSE 11.0.2 RELEASE NOTES 76 „ ERX310, ERX7xx, and ERX14xx System Maximums Ethernet S-VLANs per I/O module FE-8 I/O and FE-8 SFP I/O 16,384 16,384 16,384 16,384 GE I/O 16,384 16,384 16,384 16,384 GE-2 SFP I/O 16,384 – – 16,384 GE-8 I/O 16,384 – – 16,384 OC3-2 GE APS I/O 16,384 16,384 16,384 16,384 Ethernet VLANs per chassis (See Note 2 on page 74. ...