Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 Command Reference Manual

Description Sets the name for the router; this hostname subsequently appears in the router CLI prompt. The no version removes the hostname from the router. NOTE: In Domain Map Tunnel Configuration mode, this command has been replaced by the clear ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 Description From Domain Map Tunnel Configuration or Tunnel Group Tunnel Configuration mode, sets a hostname for a tunnel that the LAC uses when communicating with the LNS about the tunnel. The no version removes the hostname from the t ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 no boot revert-tolerance Release Information Command introduced before JUNOSe Release 7.1.0. Description Sets the reversion tolerances that the boot logic uses to determine whether the router should use the normal or backup settings. Issuing this command when high availability is enabled results i ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 Description Sets the buffer weight of the queue. The no version returns the queue to its default buffer weight. Options ■ bufferWeight—Range 1–63; default value is 8 Mode Queue Profile Configuration Related Topics ■ Con ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 no hello hold-time Release Information Command introduced before JUNOSe Release 7.1.0. Description Configures the MPLS hold time, the period that a sending LSR maintains a record of link hello messages from the receiving LSR without receipt of another link hello from that LSR. Each LSR peer sends the hold time i ...

Syntax { ip | mpls } rsvp authentication [ key authkey ] no { ip | mpls } rsvp authentication [ key [ authkey ] ] Release Information Command introduced before JUNOSe Release 7.1.0. Description Assigns a key to the interface for MD5 authentication between RSVP peers. Assign the key before you enable authentication on the interfac ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 no clns host name Release Information Command introduced before JUNOSe Release 7.1.0. Description Defines a name-to-NSAP mapping that can then be used with commands requiring NSAPs. Enables dynamic resolution of hostnames to system IDs (within the NSAP address). The hostname mapping is sent in the LSPs within the dynamic ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 Syntax multicast group port interfaceSpecifier limit groupLimit no multicast group port interfaceSpecifier limit Release Information Command introduced before JUNOSe Release 7.1.0. Description Limits the number of IGMP or MLD groups that a port can accept. The no version restores the default situation, in which there is no limit to ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 mpls ldp disable ........................................................................................1336 mpls ldp discovery transport-address ........................................................1337 mpls ldp egress-label ........................ ...

no exception source Release Information Command introduced before JUNOSe Release 7.1.0. Description Specifies the IP address and mask of the router interface over which you want to send the core dump file to the remote FTP server. The no version returns the value to its default (null). Options ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 Syntax baseline suspicious-control-flow-detection counts Release Information Command introduced in JUNOSe Release 7.3.0. Description Sets a baseline for statistics for suspicious control flow detection. There is no no version. Mode Privileged Exec, User Exec 270 ■ baseline suspicious-control-flow-detection ...

Juniper JUNOSE SOFTWARE 11.0.X - COMMAND REFERENCE A TO M 1-11-2010 no ip-hint Release Information Command introduced before JUNOSe Release 7.1.0. Description When enabled, the E Series router preallocates an IP address for the remote (B-RAS) user before calling authentication. The address is then passed as a hint in the authentication request to the RADIUS server. The no version d ...