Euphonix SH612 Operation & User’s Manual

Front and Rear Panel Interface 15 2.1.4 MADI Indicators Twelve back-lit buttons indicate the MADI input channel status. Figure 2-6 MADI Buttons Each button corresponds to the physical MADI input/output port of the same number. The SH612 software detects the physical MADI ports connected upon startup and con- tinuously mon ...

Euphonix SH612 Integration With Jupiter VM3000 Routers 28 9. When finished, click Apply and Close to close the dialog. 4.2.3 Switcher Input 1. If you have multiple switchers, select Jupiter->Switcher Input in the Config- urator. This displays a dialog to choose which switcher to edit. 2. Click the switcher added in Switcher Description ...

Euphonix SH612 Integration With Jupiter VM3000 Routers 29 5. When finished entering all inputs, click Apply and Close. 6. Save the configuration set. 4.2.4 Switcher Output 1. If you have multiple switchers, select Jupiter->Switcher Output in the Con- figurator. This displays a dialog to choose which switcher to edit. 2. Click the switch ...

Euphonix SH612 Integration With Jupiter VM3000 Routers 26 1. Enter the MADI Routing menu using the SpinKnob. 2. For each MADI port, switch it to Non-Audio Deck and press Select to confirm the selection. 3. Connect an RS-422 cable (9-pin, male-to-male, straight-through) between the SH612’s Control port (bottom-right of the rear panel) ...

19 Chapter 3: Standalone MADI Routing This configuration requires an SH612 with non-ES firmware loaded (check that the firmware version number displayed on the LCD at startup does not have “ES” after it). This is the standard mode of operation for the Studio Hub. 3.1 Connections If you have not done so, first check th ...

Euphonix SH612 Standalone MADI Routing 23 To create a route: 1. Select the Signal Source device to Route from. The device’s outputs are displayed in the window below. 2. Select the Signal Destination device to route to. The device’s inputs are displayed in the window below. 3. Select the output channel from the Signal Source and the ...

Euphonix SH612 Standalone MADI Routing 21 Figure 3-2 Edit Current Configuration tab Under the heading MADI Devices in System, make sure all the system components are listed and that the Studio Hub is the correct size. Remove unwanted components by highlighting them and clicking the Remove Device button. Add a component by click- ing the ...

Euphonix SH612 Front and Rear Panel Interface 12 Figure 2-3 LCD Menu Display 2.1.2 Menu Controls Six front panel controls interface to the menu system: Figure 2-4 Menu Controls on Front Panel Info Press Info to display the current firmware version. Arrow Keys The arrow keys do one of the following three things depending on the context i ...

Euphonix SH612 Menu Reference and Technical Specifications 32 5.1.1 Quick Setup Menu The Quick Setup menu has the most commonly used parameters gathered in one menu for quick and easy access. Refer to the individual menus for explanation of each parameter. Figure 5-2 Quick Setup Menu Sample Rate Source AES Sample Rate Quick Setup Menu S ...

Euphonix SH612 Standalone MADI Routing 22 Example: 1. Under Studio Hub Output Connections, select MADI Out #3. 2. Under MADI Devices in System, navigate to and select the MADI In #1 of the Audio Deck #1. 3. Click the Declare Connection button to solidify the connection. To erase a connection, select Unconnected Port in the MADI Devices ...

v List of Figures 2-1 SH612 Front Panel ............................................................................................................11 2-2 LCD Display .....................................................................................................................11 2-3 LCD Menu Display ............... ...

Euphonix SH612 Standalone MADI Routing 20 Figure 3-1 Configuration and Patches tab • New: creates a new blank patch. • Recall: activates the selected patch. • Store: stores the patch settings. Select the Edit Current Configuration tab. The following buttons are available: • Add Device • Rename Device • Remove Device • Decl ...