Omron CX-PROCESS TOOL - INTRODUCTION GUIDE Introduction Manual

Starting the CX-Process Tool/Making a New Project Starting the CX-Process Tool 1 Making a New Project First, make a project. 2-1. Make a new project. Starting the CX-Process Tool Making a New Project 2 1 2 Creating Simple Function Block Data for the Loop Controller From the Start Menu, select All Programs - OMRON - CX-One - ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE Click the Settings Button. Click the Build Button. Automatically Creating the NS-series PT Screen for the Loop Controller Name the project and click the Browse (2) Button. Set the output folder, set NS 12 for the PT Model, and click the Build Button. 2-3-1. Give the project a name. Click the Browse (2) Button and select the ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE Click the Next Button. In this example, the operation cycle is set to 1 s for the entire system and the start mode is set to a hot start (i.e., operation starts with the auto/manual status held immediately before the power supply was turned OFF.) Therefore, System Common block is used at its default values. Set ITEMs for Function ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE Creating Function Block Data Creating Simple Function Block Data for the Loop Controller First, paste the function block Isolated Ai 4-point Terminal (PTS51) for analog input. Right-click in the window at the right. The pop-up menu shown in the figure at the right will be displayed. Select Register - Field Terminal from the men ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE 2-4. A project folder called "Temperature Control" is created. Click the OK Button. Select a folder in which to save the data, and then click the OK Button. The window at the right will open when the OK Button is pressed. Enter the project name. G For example, enter "Temperature Control." The folder in which the project name was en ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE 3 3-1. Double-click the CX-Designer project file. 3-2. The screen for the Loop Controller is generated automatically. The trend screen that is created can be checked by selecting items on the screen. Displaying the NS-series PT Screen for the Loop Controller 3 Displaying the NS-series PT Screen ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE not contain precautions for correct use. Always read the precautions and other required information provided in product operation manuals before using the product. The application examples provided in this catalog are for reference only. Check functions and saf ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE Right-click and select Transfer to LC . Click the OK Button. Click the OK Button. Click the OK Button. Transferring Function Block Data to the Loop Controller 8 Transferring Function Block Data to the Loop Controller Now that communications settings have been completed, transfer the function bl ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE on the CX-One CD-ROM under OMRON/CX-One/CX-Process Tool. Be sure to read the Precautions and other information at the beginning of the manual before using the CX-Process Tool. This CX-Process Tool Introduction Guide describes basic operating procedures for the CX-Process Tool. For application pre ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE 6 Thermocouple Input Unit PID Analog Output Unit Click the OK Button. Set ITEMs for Function Blocks 6 Set ITEMs for Function Blocks Next, make settings so that the pasted function blocks can be used. 6-1-1. Double-click 901. Ai 4-point (PTS51). In the same way, connect the Right Arrow of the MV_C Terminal for Basi ...

TagList) and click the Save Button. Click the OK Button. The following window will be displayed. Click the OK Button. Click the OK Button. The Face Plate Auto-Builder for NS will start. Click the Save Button. Click the OK Button. Click the OK Button. 2-2. Compile the tags. Click the OK Button. Click the OK Button. Au ...

Omron CX-PROCESS TOOL - INTRODUCTION GUIDE Automatically Creating the NS-series PT Screen for the Loop Controller 1 2 Input the Scaling Upper Limit, Scaling Lower Limit, DP (i.e., decimal point position), and Unit. Click the OK Button. Automatically create the NS-series PT screen for the Loop Controller. Start the Face Plate Auto-Builder for NS (NSFP) and the p ...