AMX RE-DM6 Manuals

Installation Guide RE-DM6 Radia Eclipse 6-Channel Dimmer Module (120 or 240 volts) Overview The RE-DM6 RADIA Eclipse 6-Channel Integrated Dimmer Module (120V: FG706-03; 240V: FG706-04) controls up to six circuits with six 1200-watt onboard dimmers (FIG. 1). The RE-DM6 is designed for use with the RDA series of enclosures, in an AMX Lighting™ modular digital dimming system. The RE-DM6 is controlled by AXLink or by dry (contact) closures. Specifications Suggested Installation Loads Caution: Pre-Installation Notes WARNING: This unit should be installed only by qualified electrical personnel, and in compliance with all national electrical codes, local codes and ordinances. To prevent possible personal injury or death, disconnect power to the enclosure at the breaker box before attempting to work with any AMX Lighting modules. • All Class 1 and 2 wiring must be connected to their dedicated terminals. • Class 1 wiring should be connected through the top of the enclosure, and Class 2 wiring through the bottom. • Load conductors must be same size as line conductors, regardless of connected load. • Disconnect power while installing or connecting the unit. • Keep top and bottom air vents clear at all times, and maintain 12” (30.48 cm) clearance around the top and bottom. • Test loads for shorts before connecting. • Class 2 wiring must be rated 300V or higher. • For indoor use only. • AC lighting loads only. • For more information, refer to the RE-DM6 instruction manual available at www.amx.com. Radia Lighting System Configuration Pages The AMX Radia Web pages provide a simple interface for users of the Radia Duet module. The web pages reside on the AMX master when running the Radia Duet module and may be accessed through Internet Explorer or Mozilla Firefox. The RE- DM6 may also be configured using NetLinx code or a terminal. For more information, refer to the RE-DM6 instruction manual available at www.amx.com. High-Voltage Connections Each AMX Lighting module has its high-voltage connectors marked on its circuit board. Line, load, and neutrals are also clearly marked. Line-in Connections • Using two feeds for Line 1 and Line 2 provides two 2400 W inputs. • Jumping Line 1 and Line 2 provides a single 2400 W input (FIG. 3). FIG. 1 RE-DM6 6-channel Integrated Dimmer Module RE-DM6 Specifications Dimensions (HW): 5.75" x 10.0" (146.05 mm x 254.00 mm) Weight: 4.5 lbs (2.04 kg) Line input: • 120, 240 VAC, single phase, 2W+G, 50/60 Hz, 2400 W, one feed • 120, 120/240, 240 VAC, single phase, 3W+G, 50/60 Hz, 4800 W, dual feed Output: • 1200 W max. per channel @120, 240 VAC • 2400 W max. total, all 6 channels on with single 2400 W feed • 4800 W max. total, all 6 channels on with dual 2400 W feeds • Line input #1 goes to dimmer 1, 3, and 5; line input #2 goes to dimmer 2, 4 and 6 • All electrical ratings are for continuous duty Wire rating: Use only copper wires rated at 75°C (167°F) min. Torque terminals: To 20 in-lbs (2.3 N/M) Maximum wire size: 10 AWG (4 mm²) Wire stripping length: 0.5" (13 mm) AXLink Port: 4-pin 3.5mm green captive wire connector - AXLink communication signaling with 12VDC power in. Aux Power: 2-pin 3.5mm green captive wire connector. This is a 12VDC power input that supplies additional power to the Radia PCB and connected Radia modules. Dry Contacts: • Emergency fire alarm relay connection - Closed relay activates preset 126. Other control is locked out until relay opens. Supports daisy chaining of up to 20 dimmers for this connection, with a maximum current requirement of 200mA when daisy-chained. • Failsafe connection - Works with a toggle switch - opening the switch triggers preset 128, closing the switch triggers preset 127. Supports daisy chaining of up to 20 dimmers for this connection with a maximum current requirement of 200mA when daisy-chained. BTU/hr: 300 single feed (2400 W); 600 dual feed (4800 W) Mounting points Power Devices Jumper Chokes Neutral High Voltage Connections External +12V Aux Power Mounting points AXLink Address DIP Switch AXLink Connector Dry Closures Line In Load Out Class 1 wiring Class 2 wiring RE-DM6 Specifications (Cont.) Idle current draw: 75 mA @ 120 VAC, 50 mA @ 240 VAC, 100 mA @ 13.5 VDC Certifications: • FCC • CE • UL North America • IEC-60950 Safety Operating Temp Range: 0° to 40°C (32° to 104°F) Included Accessories: • 2 4-pin captive 3.5mm wire connectors (41-5047) • 4 #8-32x1/2” F-point mounting screws Required Enclosures: • RDA-ENC2 (FG606-10) • RDA-ENC4 (FG606-11) • RDA-ENC6/6B (FG606-12/13/15) • RDA-ENC12B (FG606-14/16) Dimmed Switched Incandescent Motors Neon, cold-cathode Fans FIG. 2 High-voltage connections FIG. 3 Line-in Connections Neutral Load Line in Load Dual 2400 W Inputs without jumper Single 2400 W Input with jumper

Operation/Reference Guide RADIA Lighting Solutions RADIA Eclipse Dimmer Modules RE-DM4 (120V, 240V) RE-DM6 (120V, 240V) Last Updated: 6/15/2007

Installation Guide RE-DM6 Radia Eclipse 6-Channel Dimmer Module (120 or 240 volts) Overview The RE-DM6 RADIA Eclipse 6-Channel Integrated Dimmer Module (120V: FG706-03; 240V: FG706-04) controls up to six circuits with six 1200-watt onboard dimmers (FIG. 1). The RE-DM6 is designed for use with the RDA series of enclosures, in an AMX Lighting™ modular digital dimming system. The RE-DM6 is controlled by AXLink or by dry (contact) closures. Specifications Suggested Installation Loads Caution: Pre-Installation Notes WARNING: This unit should be installed only by qualified electrical personnel, and in compliance with all national electrical codes, local codes and ordinances. To prevent possible personal injury or death, disconnect power to the enclosure at the breaker box before attempting to work with any AMX Lighting modules. • All Class 1 and 2 wiring must be connected to their dedicated terminals. • Class 1 wiring should be connected through the top of the enclosure, and Class 2 wiring through the bottom. • Load conductors must be same size as line conductors, regardless of connected load. • Disconnect power while installing or connecting the unit. • Keep top and bottom air vents clear at all times, and maintain 12” (30.48 cm) clearance around the top and bottom. • Test loads for shorts before connecting. • Class 2 wiring must be rated 300V or higher. • For indoor use only. • AC lighting loads only. • For more information, refer to the RE-DM6 instruction manual available at www.amx.com. Radia Lighting System Configuration Pages The AMX Radia Web pages provide a simple interface for users of the Radia Duet module. The web pages reside on the AMX master when running the Radia Duet module and may be accessed through Internet Explorer or Mozilla Firefox. The RE- DM6 may also be configured using NetLinx code or a terminal. For more information, refer to the RE-DM6 instruction manual available at www.amx.com. High-Voltage Connections Each AMX Lighting module has its high-voltage connectors marked on its circuit board. Line, load, and neutrals are also clearly marked. Line-in Connections • Using two feeds for Line 1 and Line 2 provides two 2400 W inputs. • Jumping Line 1 and Line 2 provides a single 2400 W input (FIG. 3). FIG. 1 RE-DM6 6-channel Integrated Dimmer Module RE-DM6 Specifications Dimensions (HW): 5.75" x 10.0" (146.05 mm x 254.00 mm) Weight: 4.5 lbs (2.04 kg) Line input: • 120, 240 VAC, single phase, 2W+G, 50/60 Hz, 2400 W, one feed • 120, 120/240, 240 VAC, single phase, 3W+G, 50/60 Hz, 4800 W, dual feed Output: • 1200 W max. per channel @120, 240 VAC • 2400 W max. total, all 6 channels on with single 2400 W feed • 4800 W max. total, all 6 channels on with dual 2400 W feeds • Line input #1 goes to dimmer 1, 3, and 5; line input #2 goes to dimmer 2, 4 and 6 • All electrical ratings are for continuous duty Wire rating: Use only copper wires rated at 75°C (167°F) min. Torque terminals: To 20 in-lbs (2.3 N/M) Maximum wire size: 10 AWG (4 mm²) Wire stripping length: 0.5" (13 mm) AXLink Port: 4-pin 3.5mm green captive wire connector - AXLink communication signaling with 12VDC power in. Aux Power: 2-pin 3.5mm green captive wire connector. This is a 12VDC power input that supplies additional power to the Radia PCB and connected Radia modules. Dry Contacts: • Emergency fire alarm relay connection - Closed relay activates preset 126. Other control is locked out until relay opens. Supports daisy chaining of up to 20 dimmers for this connection, with a maximum current requirement of 200mA when daisy-chained. • Failsafe connection - Works with a toggle switch - opening the switch triggers preset 128, closing the switch triggers preset 127. Supports daisy chaining of up to 20 dimmers for this connection with a maximum current requirement of 200mA when daisy-chained. BTU/hr: 300 single feed (2400 W); 600 dual feed (4800 W) Mounting points Power Devices Jumper Chokes Neutral High Voltage Connections External +12V Aux Power Mounting points AXLink Address DIP Switch AXLink Connector Dry Closures Line In Load Out Class 1 wiring Class 2 wiring RE-DM6 Specifications (Cont.) Idle current draw: 75 mA @ 120 VAC, 50 mA @ 240 VAC, 100 mA @ 13.5 VDC Certifications: • FCC • CE • UL North America • IEC-60950 Safety Operating Temp Range: 0° to 40°C (32° to 104°F) Included Accessories: • 2 4-pin captive 3.5mm wire connectors (41-5047) • 4 #8-32x1/2” F-point mounting screws Required Enclosures: • RDA-ENC2 (FG606-10) • RDA-ENC4 (FG606-11) • RDA-ENC6/6B (FG606-12/13/15) • RDA-ENC12B (FG606-14/16) Dimmed Switched Incandescent Motors Neon, cold-cathode Fans FIG. 2 High-voltage connections FIG. 3 Line-in Connections Neutral Load Line in Load Dual 2400 W Inputs without jumper Single 2400 W Input with jumper

QUICK START GUIDE RE-DM6 Radia Eclipse 6 Dimmer Module (120 VAC/240 VAC) Overview The RE-DM6 RADIA Eclipse 6-Channel Integrated Dimmer Module (120V: FG706-03; 240V: FG706-04) controls up to six circuits with six 1200-watt onboard dimmers (FIG. 1). The RE-DM6 is designed for use with the RDA series of enclosures, in an AMX Lighting™ modular digital dimming system. The RE-DM6 is controlled by AxLink or by dry (contact) closures. Specifications Suggested Installation Loads Caution: Pre-Installation Notes WARNING: This unit should be installed only by qualified electrical personnel, and in compliance with all national electrical codes, local codes and ordinances. To prevent possible personal injury or death, disconnect power to the enclosure at the breaker box before attempting to work with any AMX Lighting modules. • All Class 1 and 2 wiring must be connected to their dedicated terminals. • Class 1 wiring should be connected through the top of the enclosure, and Class 2 wiring through the bottom. • Load conductors must be same size as line conductors, regardless of connected load. • Disconnect power while installing or connecting the unit. • Keep top and bottom air vents clear at all times, and maintain 12” (30.48 cm) clearance around the top and bottom. • Test loads for shorts before connecting. • Class 2 wiring must be rated 300V or higher. • For indoor use only. • AC lighting loads only. • For more information, refer to the RE-DM6 instruction manual available at www.amx.com. Radia Lighting System Configuration Pages The AMX Radia Web pages provide a simple interface for users of the Radia Duet module. The web pages reside on the AMX master when running the Radia Duet module and may be accessed through Internet Explorer or Mozilla Firefox. The RE-DM6 may also be configured using NetLinx code or a terminal. For more information, refer to the RE-DM6 instruction manual available at www.amx.com. High-Voltage Connections Each AMX Lighting module has its high-voltage connectors marked on its circuit board. Line, load, and neutrals are also clearly marked. Line-in Connections • Using two feeds for Line 1 and Line 2 provides two 2400 W inputs. • Jumping Line 1 and Line 2 provides a single 2400 W input (FIG. 3). FIG. 1 RE-DM6 6-CHANNEL INTEGRATED DIMMER MODULE RE-DM6 SPECIFICATIONS Dimensions (HW): 5.75" x 10.0" (146.05 mm x 254.00 mm) Weight: 4.5 lbs (2.04 kg) Line input: • 120, 240 VAC, single phase, 2W+G, 50/60 Hz, 2400 W, one feed • 120, 120/240, 240 VAC, single phase, 3W+G, 50/60 Hz, 4800 W, dual feed Output: • 1200 W max. per channel @120, 240 VAC • 2400 W max. total, all 6 channels on with single 2400 W feed • 4800 W max. total, all 6 channels on with dual 2400 W feeds • Line input #1 goes to dimmer 1, 3, and 5; line input #2 goes to dimmer 2, 4 and 6 • All electrical ratings are for continuous duty Wire rating: Use only copper wires rated at 75°C (167°F) min. Torque terminals: To 20 in-lbs (2.3 N/M) Maximum wire size: 10 AWG (4 mm²) Wire stripping length: 0.5" (13 mm) AxLink Port: 4-pin 3.5mm green captive wire connector - AxLink communication signaling with 12VDC power in. Aux Power: 2-pin 3.5mm green captive wire connector. This is a 12VDC power input that supplies additional power to the Radia PCB and connected Radia modules. Dry Contacts: • Emergency fire alarm relay connection - Closed relay activates preset 126. Other control is locked out until relay opens. Supports daisy chaining of up to 20 dimmers for this connection, with a maximum current requirement of 200mA when daisy-chained. • Failsafe connection - Works with a toggle switch - opening the switch triggers preset 128, closing the switch triggers preset 127. Supports daisy chaining of up to 20 dimmers for this connection with a maximum current requirement of 200mA when daisy-chained. BTU/hr: 300 single feed (2400 W); 600 dual feed (4800 W) Mounting points (x4) Jumper Load out Neutral Chokes High Voltage External +12 Dry Closures AxLink Connector Power Devices 4-Pin Connectors to Line In Connections RDM Series Modules AxLink Address DIP Switch Aux Power CLASS 1 WIRING CLASS 2 WIRING RE-DM6 SPECIFICATIONS (CONT.) Idle current draw: 75 mA @ 120 VAC, 50 mA @ 240 VAC, 100 mA @ 13.5 VDC Certifications: • FCC • CE • UL North America • IEC-60950 Safety Operating Temp Range: 0° to 40°C (32° to 104°F) Included Accessories: • 2 4-pin captive 3.5mm wire connectors (41-5047) • 4 #8-32x1/2” F-point mounting screws Required Enclosures: • RDA-ENC2 (FG606-10) • RDA-ENC4 (FG606-11) • RDA-ENC6/6B (FG606-12/13/15) • RDA-ENC12B (FG606-14/16) DIMMED SWITCHED Incandescent Motors Neon, cold-cathode Fans FIG. 2 HIGH-VOLTAGE CONNECTIONS FIG. 3 LINE-IN CONNECTIONS Neutral Load Line in Load Dual 2400 W Inputs without jumper Single 2400 W Input with jumper