Axis Q6035 Manuals

Axis P55 & Q60 HD network/IP PTZ cameras with Dotworkz D2 Outdoor Housing - 10 minute installation guide www.dotworkz.com 866.575.4689 innovative remote video solutions Using the included Axis Torx screw driver unscrew all 8 bottom Torx screws (4 “outside” ones for the main cover plus 4 for smaller cables latch cover). Attach the Axis P55 or Q60 series camera collar to the Dotworkz universal camera mounting plate, making sure to line up correctly and tight- ening lock washers securely. Connect BROWN wire to (-) negative and RED to (+) positive on the MVP terminal. The BLACK wire is not used so we recommend isolating it with electrical tape. Run CAT5 cable through exist- ing D2 cable gland; Remove the plug and install an included second cable gland, making sure to seal it tight. Note: if using conduit be sure sealing to avoid water moisture. After unscrewing, remove P55 or Q60 series camera cover and open smaller cable latch. Set aside the main lower camera shroud as it is not going to be needed. You will need to use the 1.5 and the 0.75 inches stand- offs on the 4 brass inserts on top of the D2 enclosure - DO NOT over tighten or cross thread the standoffs. Have a qualified electri- cian connect an external power source to D2 terminal power block. See manual for more details. Attach the Dotworkz 5502-491 patch cable that will provide camera power; attach the RG45 connector of a CAT5 Ethernet cable to the camera; Feed both cables out their respective slots. Twist-lock camera into collar while applying down pressure; line up the diamond mark as in this picture; Secure the camera plate to the standoffs using included 832 pan head screws. Make sure to have only one cable per gland and tighten them really shut to com- pletely seal D2 enclosure from the outside. Securely close the cable latch using the Torx screw driver again. Remove the terminal block from Dotworkz 5502-491 cable: you will only use BROWN and RED wires. Check camera install by care- fully closing the D2 camera hatch and verifying clearance between camera and D2 lens: should be enough space between the clear dome and the camera to move freely. Close the enclosure and tighten all screws using a philips screw driver. The D2 can be mounted directly to a wall or to a pole mount adapter. Make sure to create a “U” shape drip loop with the cables to prevent water from pooling and possibly seeping inside. Axis Technology, Dotworkz Durability Dotworkz has created a quick “how- to” guide on proper installation of the Axis P5512, P5522, P5532, P5534, Q1755, Q6032, Q6034, Q6035 HD cameras with the Dotworkz D2 rugged IP66 camera enclosures. Guide includes step-by- step photos, procedures and tips for a fast and simple set up. The Dotworkz housings are the #1 choice available to protect Axis HD cameras. An IP66 rating assures that the cameras and all other sensitive electronic equipment are safe from environmental conditions, and secure from malicious vandals. Dotworkz enclosures are the durable solution for protecting Axis cameras from the harshest conditions. Prepare the camera Install Axis collar Correct poles IP68 Cable glands Remove shroud Mount the standoffs External power source Connect cables Secure camera Tighten cable glands Reassemble latch cover Using Dotworkz cable Check camera fit Close the D2 Leave a drip loop All the parts and tools Note: Please read both Axis and Dot- workz manuals before beginning. Photo of hardware and components needed to install Axis P55 & Q60 into the D2 outdoor enclosure system.

INSTALLATION GUIDE AXIS Q60 Series AXIS Q6032 PTZ Dome Network Camera AXIS Q6034 PTZ Dome Network Camera AXIS Q6035 PTZ Dome Network Camera ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPANÕL òò ¨¨ ¾¾

Installing Camera Bracket into D2 Axis Q6032, Q6034, & Q6035 Required components: (1) Dotworkz Universal camera bracket (1) Axis Hard Ceiling Bracket (3) # 6 machine screws, hex nuts, & washers (4) #8-32 x ½” long Pan head machines screws -Phillips 3. The Axis Q60 Series cameras do not need any standoffs. The Dotworkz Camera mount bracket will mount directly to upper mount inserts. 4. Insert the camera bracket with the hard ceiling bracket onto it into place. Line up with 4 screw posts with bracket corner mounting slots/ holes. Again, make sure the camera bracket is facing the right direction. Picture represents camera bracket orientation & how it is secured. Don’t’ forget to mount your camera to the D2 camera bracket based on instructions. Only Non -E versions will fit in Dotworkz D-Series 5. Use (4) #8-32 x ½” long screws (Phillips head) to secure the bracket into place, that are provide in Dotworkz hardware pack. Axis Hard Ceiling Bracket ring provided by Axis in all Q60 indoor Series camera systems This edge nests in arch at front of D2 This edge of the bracket faces back of the D2 6. Install Wiring on rear of camera before twist locking camera onto the key lock on hard ceiling bracket. **Skip to next page for wiring details** 7. Remove Axis Q60 Lens Bubble for best optics with Bubble mount ring. Dotworkz D2 Lens bubble will protect camera & housing. 9. Tape tamper switch down built into Axis Q60 camera housing mouth to enable camera. 1. Install the Axis P55 Hard Ceiling Bracket ring onto the D2 Camera Bracket using (3) #6 machine screws, (3) .25" Lock Washer, and (3) .25" Washer that are included. 2. Align holes as indicated on image below for quick and precise alignment of Axis bracket onto center of Dotworkz camera bracket. * Axis Q60 (non -E) ready for PoE+ powering. * Dotworkz KT-AXPH is a power harness kit made for Axis Q60 & P55 series, allowing these indoor models to be powered by 24 VAC, or 24 VDC. * Axis has a Multi-harness version for these series. 8. Twist Lock Axis housing onto pre-installed hard ceiling bracket using clockwise motion. Assure it is securely fastened.

ENGLISH DEUTSCH ITALIANO ESPAÑOL INSTALLATION GUIDE FRANÇAIS AXIS Q60 Series AXIS Q6032 PTZ Dome Network Camera AXIS Q6034 PTZ Dome Network Camera AXIS Q6035 PTZ Dome Network Camera

USER MANUAL AXIS Q6035 PTZ Dome Network Camera