Celestron 127EQ Manuals

Quick Set-up Guide 1 PowerSeeker 114EQ & 127EQ Your PowerSeeker 114EQ or 127EQ includes: optical tube w/ tube rings attached; tripod with center leg brace; equatorial mount; 2 eyepieces; a 3x barlow lens, finderscope; 6 lb. counterweight (#21049 has 6 lb. & 2 lb. counterweights); counterweight bar; two slow motion cables; eyepiece accessory tray; The Sky ® Level 1 software, owner’s manual. Item# 21045 Questions or Problems with Set-up? CONTACT: Celestron Technical Support: 310.803.5955 Item# 21049 2 3 All three legs should be the same length to provide a level platform for the telescope. 4 7 Locate the equatorial mount and place the base of the mount through the hole in the center of the tripod mounting platform. 5 Properly assembled, the accessory tray should appear as pictured above. 6 From underneath the tripod mounting platform, thread the attached mounting bolt into the hole on the bottom of the equatorial mount. 8 Thread the latitude adjustment screw into the equatorial mount until it is touching the inside of the mount. 9 Place the accessory tray on top of the tripod's center leg brace. Thread the tray into the threaded hole in the center of the leg brace. Extend the center portion of each of the three tripod legs down 6-12". Use the three tightening screws located at the bottom of each leg to secure the extended legs in place. To set up the tripod, spread the legs outward until they are fully extended and push down center leg brace. PowerSeeker 114EQ shown

Unpack your telescope and verify that all parts are present. Your PowerSeeker 114EQ or 127EQ includes: an optical tube with tube rings attached, a tripod with center leg brace, an equatorial mount, two eyepieces, a 3x Barlow lens, a finderscope, a 6 lb. counterweight, a counterweight bar, two slow motion cables, and an eyepiece accessory tray. Check to ensure that all three legs are the same height once extended to provide a level platform for the telescope. Locate the equatorial mount and place the base of the mount through the hole in the center of the tripod mounting platform. To set up the tripod, spread the legs outward until they are fully extended and push down center leg brace. Place the eyepiece accessory tray on top of the tripod’s center leg brace. Thread the tray into the threaded hole in the center of the leg brace until it is fully seated. From underneath the tripod mounting platform, thread the attached mounting bolt into the hole on the bottom of the equatorial mount. Extend the center portion of each of the three tripod legs down about 6 to 12 inches. Use the tightening screw on each leg to secure the extended leg in place. If necessary, rotate the accessory tray counterclockwise until the accessory holes are not covered by the leg brace arms as shown here. Look up the approximate latitude of your observing site on the Internet or using a map. Then, thread the latitude adjustment screw into the equatorial mount until your latitude is indicated on the latitude scale. 1 4 7 2 5 8 3 6 9 Q U I C K S E T - U P G U I D E ITEM #21045 ITEM #21049 ENGLISH 114EQ and 127EQ TELESCOPES ENGLISH

Quick Set-up Guide 1 PowerSeeker 114EQ & 127EQ Your PowerSeeker 114EQ or 127EQ includes: optical tube w/ tube rings attached; tripod with center leg brace; equatorial mount; 2 eyepieces; a 3x barlow lens, finderscope; 6 lb. counterweight (#21049 has 6 lb. & 2 lb. counterweights); counterweight bar; two slow motion cables; eyepiece accessory tray; The Sky ® Level 1 software, owner’s manual. Item# 21045 Item# 21049 2 3 All three legs should be the same length to provide a level platform for the telescope. 4 7 Locate the equatorial mount and place the base of the mount through the hole in the center of the tripod mounting platform. 5 Properly assembled, the accessory tray should appear as pictured above. 6 From underneath the tripod mounting platform, thread the attached mounting bolt into the hole on the bottom of the equatorial mount. 8 Thread the latitude adjustment screw into the equatorial mount until it is touching the inside of the mount. 9 Place the accessory tray on top of the tripod's center leg brace. Thread the tray into the threaded hole in the center of the leg brace. Extend the center portion of each of the three tripod legs down 6-12". Use the three tightening screws located at the bottom of each leg to secure the extended legs in place. To set up the tripod, spread the legs outward until they are fully extended and push down center leg brace. PowerSeeker 114EQ shown

ENGLISH | 1 Unpack your telescope and verify that all parts are present. Your PowerSeeker 127EQ includes: a telescope tube with two tube rings attached, a tripod with center leg brace, an equatorial mount, two eyepieces, a 3x Barlow lens, a fi nderscope, a 6 lb. counterweight, a counterweight bar, two slow motion cables, a 1/4-20 mounting stud on one tube ring (for cameras), a lens cleaning cloth, tripod multi- tool and an Allen wrench for secondary mirror adjustments, and an eyepiece accessory tray. Check to ensure that all three legs are the same height once extended to provide a level platform for the telescope. Locate the equatorial mount and place the base of the mount through the hole in the center of the tripod mounting platform. To set up the tripod, spread the legs outward until they are fully extended and push down center leg brace. Place the eyepiece accessory tray on top of the tripod’s center leg brace. Thread the tray into the threaded hole in the center of the leg brace until it is fully seated. From underneath the tripod mounting platform, thread the attached mounting bolt into the hole on the bottom of the equatorial mount. Extend the center portion of each of the three tripod legs down about 6 to 12 inches. Use the tightening screw on each leg to secure the extended leg in place. If necessary, rotate the accessory tray counterclockwise until the accessory holes are not covered by the leg brace arms as shown here. Look up the approximate latitude of your observing site on the Internet or using a map. Then, thread the latitude adjustment screw into the equatorial mount until your latitude is indicated on the latitude scale. 1 4 7 2 5 8 3 6 9 #21049 Q U I C K S E T U P G U I D E ENGLISH 127EQ