Compaq DS10 Manuals

1 EK–DS10S–RM. A01 ALPHASERVER DS10 RACKMOUNT GUIDE Overview • Rackmount Guidelines • Unpack Rackmount Box • Determine Base Zero • Mark and Prepare the Rails • Install the Rails • Attach the Rackmount Ears • Insert and Secure the System • Check Power and Secure Cables • For More Information WARNING: To prevent injury, access is limited to persons who have appropriate technical training and experience. Such persons are expected to understand the hazards of working within this equipment and take measures to minimize danger to themselves or others. Rackmount Guidelines. • A maximum of six systems per each power controller unit in a rackmount cabinet. Unpack Rackmount Box The rackmount box is one of three long boxes found in the system’s shipping carton (see Figure 1). It contains these instructions, two rails, U-clips and screws, and two rackmount ears for securing the system in the rack. Figure 1 Unpacking the Rackmount Kit PK1038-99 Determine Base Zero Decide the relative position of the system in the rack. Base zero is where the bottom of the system will be when installed in the rack. If your system is the first system in the rack, then base zero is between the 6th and 7th hole up from the floor of the rackmount cabinet. This distance allows the system to clear the power controllers and provide space for cable management. If you are adding your system to a rack already populated, then base zero is the top of the system underneath the system to be installed. This system needs a clearance of 9 holes to accommodate the system height. Mark and Prepare the Rails • Using the template on the back of this card ( • Figure 9) mark holes 2 and 5 on an interior rail, and base zero (see Figure 2). Figure 2 Using the Template PK1033-99 2 5 Base 0 Top • Mark all four of the inner rails (see Figure 3). • If you are installing more than one AlphaServer DS10 in the rack at the same time: using the template, mark the top of the first system you are installing. Use this as base zero for the second system, move the template up, mark holes 2 and 5, and the top of this system, until you have marked holes for all of systems you are installing. • Insert a U-clip at each hole you have marked. Figure 3 Marking Inner Rails PK1033a-99 2 5

Compaq Computer Corporation AlphaServer DS10 Console Reference Order Number: EK–DS10S–CR. B01 This manual describes the general operations of the AlphaServer DS10 system. It presents the SRM console (the command-line interface for Tru64 UNIX and OpenVMS operating systems), AlphaBIOS (the graphics interface for Windows NT and Linux), and remote console management.

© Digital Equipment Corporation 1999. All rights reserved. 1 EK–DS10S–UR. A01 ALPHASERVER DS10 USER REFERENCE CARD This document is intended as a quick reference for the user. Additional information can be found in the AlphaServer DS10 / AlphaStation VS10 Console Reference guide, EK-DS10S-CR. Overview • Environmental Specifications • Mechanical Specifications • Electrical Specifications • Front Buttons and LEDs • Ethernet LEDs • Beep Codes • PCI Slots • Memory Configuration • SRM Console Commands • Remote Management Console (RMC) Commands • Acoustics WARNING: To prevent injury, access is limited to persons who have appropriate technical training and experience. Such persons are expected to understand the hazards of working within this equipment and take measures to minimize danger to themselves or others. CPU modules and memory modules have parts that operate at high temperatures. Wait 2 minutes after power is removed before touching any module. Wear an antistatic wrist strap when working on this system. To reduce the risk of electrical shock or damage to the equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Disconnect power by unplugging the power cord from the electrical outlet or the workstation. Environmental Specifications Storage temperature range –40º C to 66º C (–40º F to 151º F) Operating temperature range 10º C to 40º C (50º F to 104º F) Max. rate of change 11º C (20º F) per hour Storage humidity range (noncondensing) 10% to 90% relative humidity; maximum wet bulb 65º C (149º F) Operating humidity range (noncondensing) 10% to 90% relative humidity (without removable media) or 20% to 80% relative humidity (with removable media); maximum wet bulb 2º C (36º F) Max. altitude Nonoperating–4867 m (16,000 ft.); Operating—2400 m (8,000 ft.) Nonoperating shock 30 G, 25 ms halfsine Mechanical Specifications Leave ventilation room at the front and rear of the system. PK1015 Height 13 cm (5 in.) Width 43 cm (17 in.) Depth 46 cm (18 in.) Weight 14.5 kg (32 lb) Electrical Specifications • Check your power supply setting. • Secure the power cord by turning the safety latch clockwise over the power cord. Secure the latch by tightening it with a screwdriver. 115V 230V PK1047a

Compaq AlphaServer DS10 Systems Technical Summary