CyberPower PR750LCDRM1U Manuals

1 2 3 6 4 5 Battery Replacement 1. Place the UPS on its top and remove the retaining screw (figure 1). 2. Slide the battery compartment cover completely off of the unit (figure 2). 3. Remove the battery from the compartment and disconnect the battery wires from the battery. Install the replacement battery by connecting the red wire to the positive (+) terminal and the black wire to the negative (-) terminal of the battery. (figure 3) 4. Slide the battery compartment cover over the battery and tighten the retaining screw. 5. Charge the unit for 4 – 8 hours to ensure the UPS performs expected runtimes. MODEL: CP600LCD, CP825LCD, CP800AVR, CP685AVR-G, CP825AVR-G, CP685AVRLCD-G, CP825AVRLCD-G, AVRG750U, AVRG900U, AVRG750LCD, AVRG900LCD 1. Place the UPS on its side and locate the battery compartment cover on the bottom of the UPS. Remove the four (4) retaining screws and pull the battery compartment cover off the UPS (figure 1 & 2). 2. Remove the battery from the compartment and disconnect the battery wires from the batteries. Install the replacement batteries by connecting the red wire and black wire to the same color wires from the battery pack. Put the battery pack into the compartment (figure 3). 3. Slide the battery compartment cover over the battery and tighten the retaining screw. Charge the unit for 4 – 8 hours to ensure the UPS performs expected runtimes. MODEL: CP850AVRLCD, CP1000AVRLCD Intelligent LCD Series, AVR Series 1 2 3 1. Remove the front panel of the UPS. 2. Pull out both round knobs and remove the battery compartment cover completely off of the unit. 3. Remove the batteries from the compartment. 4. Disconnect the battery wires from the batteries. 5. Install the replacement batteries by connecting the wire bundle (composed of one red wire and one black wire) to the connector from the battery pack. Put the batteries back into the compartment. 6. Re-install the battery compartment cover and push both round knobs back into place. Put the front panel back on the UPS. 7. Connect to AC power and charge the new batteries for up to 16 hours to insure a full charge. MODEL: PR750LCD Smart APP SINEWAVE Series 1. Place the UPS on its side to locate and remove the front panel retaining screws from the bottom of the UPS. 2. Slide the cover (front panel) towards the bottom of the UPS. 3. Remove it from the unit. 4. Disconnect the cable located at the top of the cover. 5. Disconnect the battery wires from the batteries. 6. Remove the batteries from the compartment. 7. Install the replacement batteries by connecting the red and black wires to the same color wires from the battery pack. Put the battery pack back into the compartment. 8. Replace the battery compartment cover and tighten the retaining screw. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 1. Remove the right side front panel. 2. Remove the three retaining screws for the cable protection cover and remove the cover. 3. Disconnect the black and red cable. 4. Remove the one retaining screw holding the battery pack in place. 5. Remove the battery pack. 6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. MODEL: CP900AVR, CP1200AVR, CP1500AVRT, CP1285AVRLCD, CP1350AVRLCD, CP1500AVRLCD 1. Remove the right side front panel. 2. Remove the three retaining screws for the cable protection cover and remove the cover. 3. Remove the two retaining screws from the cable connectors. 4. Disconnect the black and red cable. 5. Remove the four retaining screws holding the battery pack in place. 6. Remove the battery pack. 7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 1. Remove the right side front panel. 2. Remove the two retaining screws for the cable protection cover and remove the cover. 3. Disconnect the black and red cable. 4. Remove the four retaining screws holding the battery pack in place. 5. Remove the battery pack. 6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. MODEL: OR1500LCDRM2U, OR2200LCDRM2U, OR1500LCDRTXL2U, OR2200LCDRTXL2U MODEL: CPS1500AVR AVR Series MODEL: OR500LCDRM1U, OR700LCDRM1U, OR1000LCDRM1U, OR1500LCDRM1U Smart APP Intelligent LCD Series 1 3 2 1 2 3 6 4 5 1 2 4 5 3 4 1 2 3 5 6 WARNING BATT BATTERY USING ! ON POWER LOAD AVR WARNING LOAD BATT ON POWER AVR BATTERY USING ! WARNING LOAD BATT ON POWER AVR BATTERY USING ! WARNING BATT USING ! LOAD ON POWER AVR BATTERY BATTERY AVR POWER ON LOAD ! USING BATT WARNING 1 2 4 5 3 R R 750VA 1 2 4 3 1 2 4 3 R 1. Remove the front panel of the UPS. 2. Remove two screws from the battery compartment cover and slide the cover completely off of the unit. 3. Remove the batteries from the compartment. Disconnect the battery wires from the batteries. 4. Install the replacement batteries by connecting the wire bundle (composed of one red wire and one black wire) to the connector from the battery pack. 5. Put the batteries back into the compartment. Re-install the battery compartment cover and tighten the retaining screws. Put the front panel back on the UPS. 6. Connect to AC power and charge the new batteries for up to 16 hours to insure a full charge. MODEL: PR1000LCD 1. Remove the front panel of the UPS. 2. Remove two screws from the battery compartment cover and slide the cover completely off of the unit. 3. Remove the batteries from the compartment. Disconnect the battery wires from the batteries. 4. Install the replacement batteries by connecting the wire bundle (composed of one red wire and one black wire) to the connector from the battery pack. 5. Put the batteries back into the compartment. Re-install the battery compartment cover and tighten the retaining screws. Put the front panel back on the UPS. 6. Connect to AC power and charge the new batteries for up to 16 hours to insure a full charge. MODEL: PR1500LCD 1 3 4 2 1. Remove the right side front panel. 2. Remove the two retaining screws for the cable protection cover and remove the cover. 3. Disconnect the black and red cable. 4. Remove the one retaining screw holding the battery pack in place. 5. Remove the battery pack. 6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse sequence of the above steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. MODEL: PR750LCDRM1U, PR1000LCDRM1U 1 2 4 5 3 1. Remove the right side front panel. 2. Remove the two retaining screws for the cable protection cover and remove the cover. 3. Disconnect the black and red cable. 4. Remove the four retaining screws holding the battery pack in place. 5. Remove the battery pack. 6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. MODEL: PR1500SWRM2U, PR2200SWRM2U WARNING BATT BATTERY USING ! ON POWER LOAD AVR WARNING LOAD BATT ON POWER AVR BATTERY USING ! WARNING LOAD BATT ON POWER AVR BATTERY USING ! WARNING BATT USING ! LOAD ON POWER AVR BATTERY BATTERY AVR POWER ON LOAD ! USING BATT WARNING 1 2 4 5 3 1. Remove the front panel of the UPS and two screws from the battery compartment cover and slide the cover completely off of the unit. 2. Pull out the battery pack on the outside from the compartment. Disconnect the battery connector from the batteries. 3. Before removing the battery pack on the inside, unlock the cable tie and pull out the battery wires. Disconnect the battery connector from the batteries. 4. Install the replacement battery pack on the inside by connecting the wire bundle connector (composed of one red wire and one black wire) to the connector from the battery pack. Lock the battery wires back with the cable tie. 5. Install the replacement batteries on the outside by connecting the wire bundle connector (composed of one red wire and one black wire) to the connector from the battery pack. Put the battery pack on the outside back into the compartment. 6. Re-install the battery compartment cover and tighten the retaining screws and put the front panel back on the UPS. 7. Connect to AC power and charge the new batteries for up to 16 hours to insure a full charge. Note: The battery pack on the outside has a fuse, while the battery pack on the inside does not. MODEL: PR2200LCD, PR3000LCD 1 2 3 4

WARNING BATT BATTERY USING ! ON POWER LOAD AVR WARNING LOAD BATT ON POWER AVR BATTERY USING ! WARNING LOAD BATT ON POWER AVR BATTERY USING ! WARNING BATT USING ! LOAD ON POWER AVR BATTERY BATTERY AVR POWER ON LOAD ! USING BATT WARNING 1. Remove the right side front panel. 2. Remove the three retaining screws for the cable protection cover and remove the cover. 3. Remove the two retaining screws from the cable connectors. 4. Disconnect the black and red cable. 5. Remove the four retaining screws holding the battery pack in place. 6. Remove the battery pack. 7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 1. Remove the right side front panel. 2. Remove the three retaining screws for the cable protection cover and remove the cover. 3. Disconnect the black and red cable. 4. Remove the one retaining screw holding the battery pack in place. 5. Remove the battery pack. 6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 1. Remove the right side front panel. 2. Remove the two retaining screws for the cable protection cover and remove the cover. 3. Disconnect the black and red cable. 4. Remove the four retaining screws holding the battery pack in place. 5. Remove the battery pack. 6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 1. Remove the six retaining screws, and remove the front panel from the UPS. 2. Remove the two retaining screws for the cable protection cover and remove the cover. 3. Remove the two retaining screws from the cable connectors. 4. Disconnect the black and red cable. 5. Remove the three retaining screws holding the battery pack in place. 6. Remove the battery pack. 7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previo steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 1. Remove the right side front panel. 2. Remove the two retaining screws for the cable protection cover and remove the cover. 3. Disconnect the black and red cable. 4. Remove the one retaining screw holding the battery pack in place. 5. Remove the battery pack. 6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse sequence of the above steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 1. Remove the right side front panel. 2. Remove the three retaining screws for the cable protection cover and remove the cover. 3. Remove the two retaining screws from the cable connectors. 4. Disconnect the black and red cable. 5. Remove the four retaining screws holding the battery pack in place. 6. Remove the battery pack. 7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previo steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes. 4 1 2 3 5 6 1 2 4 5 3 Smart APP Intelligent LCD Series MODEL: OR500LCDRM1U, OR700LCDRM1U, OR1000LCDRM1U, OR1500LCDRM1U MODEL: OR1500LCDRM1U, OR2200LCDRM2U, OR1500LCDRTXL2U, OR2200LCDRTXL2U 1 2 4 5 3 1 2 4 5 3 Smart APP SINEWAVE Series MODEL: PR750LCDRM1U, PR1000LCDRM1U MODEL: PR1500SWRM2U, PR2200SWRM2U 6 5 4 1 2 3 2 1 ! 3 4 5 6 Smart APP SINEWAVE Series MODEL: PR1000LCDRT2U, PR1000LCDRTXL2U, PR1500LCDRT2U, PR2200LCDRT2U, PR3000SWRM2U MODEL: PR1000LCDRTXL2Ua, PR1500LCDRTXL2U, PR2200LCDRTXL2U, PR3000LCDRT2U, PR3000LCDRTXL2U

Smart App Sinewave Series PR750LCDRM1U/PR1000LCDRM1U User’s Manual K01-0000059-04 This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate. CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection. DO NOT plug the UPS into an outlet that is not grounded. If you need to de-energize this equipment, turn off and unplug the UPS. CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical applications. DO NOT use in any circumstance that would affect operation or safety of any life support equipment, with any medical applications, or patient care. CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected. CAUTION! For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of conductive contaminants. (Please see specifications for acceptable temperature and humidity range). CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery. There are no serviceable parts inside, except for the battery. CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer component. CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause the machine to short out. CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser printers are too large for a UPS. UNPACKING Inspect the UPS upon receipt. The box should contain the following. (1) UPS Unit; (1) User's Manual for UPS; (2) Rack mount Brackets; (1) Emergency Power Off Cable (gray) (1) PowerPanel® Business Edition Software CD; (1) Serial Interface Cable (DB-9); (1) USB A+B type cable; (1) Warranty Registration Card. OVERVIEW The PR750LCDRM1U/PR1000LCDRM1U provides automatic voltage regulation for inconsistent utility power. The PR750LCDRM1U/PR1000LCDRM1U features 1874 Joules of surge protection, and provides battery backup during power outages. The PR750LCDRM1U/PR1000LCDRM1U ensures consistent power to your computer system and its included software will automatically save your open files and shutdown your computer system during a utility power loss. AUTOMATIC VOLTAGE REGULATOR(AVR) The PR750LCDRM1U/PR1000LCDRM1U stabilizes inconsistent utility power. The incoming utility power may be damaging to important data and hardware, but with Automatic Voltage Regulation, the computer will not experience damaging voltage levels. An Automatic Voltage Regulator automatically increases low or decreases high voltage to a consistent, computer safe 110v/120v. The unit powerful sealed lead-acid batteries will provide power only if the incoming voltage drops below 80v or increases above 150v. SYSTEM BLOCK DIAGRAM HARDWARE INSTALLATION GUIDE 1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least four hours is recommended to ensure that the battery's maximum charge capacity is achieved. Charge loss may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into an AC outlet. The unit will charge in both the on and off position. 2. If you will use the software, connect the serial interface cable to the serial port on the UPS and the computer. If you would like to use USB cable, please connect the USB cable on the UPS then connect the USB cable to your computer. 3. With the UPS unit off and unplugged, connect your computer, monitor, and any externally powered data storage device (Hard drive, Tape drive, etc.) into the battery power supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device into the UPS. The power demands of these devices will overload and possibly damage the unit. 4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air conditioner, refrigerator, copier, etc.). Avoid using extension cords. 5. Depress the power switch to turn the unit on. The power on indicator light will illuminate. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker is depressed and then turn the UPS on. 6. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will automatically recharge. 7. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times. 8. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to ensure battery life. 9. Professional Rack Mount UPS provides one serial port, one dry contact and one USB port to allow connection and communication between the UPS and computers or equipment. This allows the simultaneous shutdown of two computer systems. Serial port II produces the basic information for equipment that can utilize a dry contact ups. The Primary computers (with PowerPanel® Business Edition installed) are the computers that you will use to control the UPS and make any changes to the operation of the UPS. When there is a power failure, the computer which connects to Primary port will start to shutdown after a user controlled delay. PowerPanel® Business Edition will save and close any open files prior to shutting the system down. 10. EPO (Emergency Power Off) Port: The feature is for the application to enable emergency power shutdown. Use the gray cable provided to connect the UPS to a normally closed or normally open contact switch according to the circuit diagram. EPO function is provided in the UPS. EPO remote switch which is a Push-Back button installed computer room outside by a phone line, and not connected any other equipment. FRONT / REAR PANEL DESCRIPTION 1. Power Switch Master on/off switch for equipment connected to the UPS. 2. Power On Indicator Indicates the power is on. 3. LCD Module Display LCD shows all the UPS information with icons and messages. 4. LCD Display Toggle Button The button can be used to toggle between different data displays on the LCD. 5. Battery Backup Protected Outlets Provides eight battery powered, surge protected and AVR outlets for connected equipment and ensures temporary uninterrupted operation of connected equipment during a power failure. Critical /Non-critical When the UPS is overloaded, the circuit breakers will be tripped to interrupt the power supply to the uncritical outlets while continuing to supply the critical outlets. As well, as the battery capacity depletes under the threshold value, the uncritical outlets will be shut down and provide energy for critical outlets. The threshold can be determined and set by users. Non-critical outlets can also be turned on/off manually through the software package provided. 6. Input Power Cord Heavy-duty, extra long power cord. 7. Input Circuit Breaker Resettable circuit breakers provide Input optimal overload Protection. Contact your dealer, or email [email protected]. Refer to replacement battery pack number RBP422 for PR750LCDRM1U/PR1000LCDRM1U. Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the supervision of personnel knowledgeable of batteries and their precautions. Servicing the battery should only be performed by trained personnel. Replacement of batteries located in an OPERATOR ACCESS AREA. CAUTION! When replacing batteries, replace with the same number of the following battery: HR9-6(BB) for PR750LCDRM1U/ PR1000LCDRM1U. CAUTION! Risk of Energy Hazard, 6V, maximum 9 Ampere-hour (HR9-6) batteries. Before replacing batteries, remove conductive jewelry such as chains, wrist watches, and rings. High energy through conductive materials could cause severe burns. CAUTION! Risk of battery explosion, if battery is replaced by an incorrect type. Dispose of used battery according to the instructions. CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit overcurrent protection in accordance with the National Electric Code, ANSI/NFPA 70. CAUTION! Use only the specified type of battery. See your dealer for replacement batteries. CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as they may explode. Follow all local ordinances regarding proper disposal of batteries. CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin and eyes and may be toxic. CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following precautions before replacing the battery: 1. Remove all watches, rings or other metal objects. 2. Only use tools with insulated handles. 3. Do not lay tools or metal parts on top of battery or any terminals. 4. Wear rubber gloves and boots. 5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground. CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such shock will be reduced if such grounds are removed during installation and maintenance (applicable to a UPS and a remote battery supply not having a grounded circuit) BATTERY REPLACMENT PROCEDURE: . Line mode UPS Status Display Capacity Display Digital Value Display Select SW Press Load Cap Battery Cap Input Voltage Output Voltage Run Time % of Load % of Battery Initial V X -- X V V 1st V X -- X V V 2nd V X -- X V V 3rd V X -- X V V 4th V X -- X V 5th(return) V X -- X V V (overload) V X -- V -- -- -- -- -- V -- Battery Mode UPS Status Display Capacity Display Digital Value Display Select SW Press Load Cap Battery Cap Input Voltage Output Voltage Run Time % of Load % of Battery Initial X V -- X V V 1st X V -- X V V 2nd X V -- X V V 3rd X V -- X V V 4th X V -- X V 5th(return) X V -- X V V Press>4sec (sound disable) X V V X -- -- -- -- -- -- Press>4sec again(sound enable) X V X X -- -- -- -- -- -- -- overload X V -- V -- -- -- -- V -- “V” illuminated , “X” Not illuminated, “— “ either IMPORTANT SAFETY WARNINGS INSTALLING YOUR UPS SYSTEM 1. Remove the right side front panel 2. Remove the two retaining screws of the cable protection cover then remove the cover. 3. Disconnect the black and red cable. 4. Remove the one retaining screws 5. Charge a new battery pack. Assemble the screws cover cable and front panel in the reverse sequence of above steps. Recharge the unit for4-8 hours to ensure the UPS performs expected runtime LCD STATUS DEFINITION BATTERY REPLACEMENT 8. USB port USB communication port for management software. 9. Serial Port Serial port allows connection and communication between the UPS and the computer. 10. SNMP/HTTP Network slot Remove the cover panel to install optional RMCARD that allows remote monitoring and control your UPS on networks. 11. Site Wire Fault Indicator This LED will illuminate to warn the user that a wiring problem exists within the AC receptacle, such as a bad ground, missing ground or reversed wiring. If illuminated, disconnect all equipment and contact an electrician to ensure outlet is properly wired. 12. EPO (Emergency Power Off) port The interface can be used to connect to switches for emergency power off. BASIC OPERATION When you first receive the unit, plug in the unit to fully charge the battery. Unplug the unit and turn Power Off when first connecting your computer and peripherals.