Ei Electronics Ei 3100RF Manuals

1 Radio Wireless Interconnect Instruction Leaflet Contains vital information on unit operation and installation. Read and retain carefully. If you are just installing the unit, this leaflet MUST be given to the householder. Models: Ei3100RF / Ei3500RF Ionisation Smoke Alarms Ei3105RF Optical Smoke Alarm with Hush Feature P/N B15527 Rev5 © Ei Electronics 2013 SMOKE ALARM

1 SMOKE ALARM Radio Wireless Interconnect Instruction Leaflet Contains vital information on unit operation and installation. Read and retain carefully. If you are just installing the unit, this leaflet MUST be given to the householder. Model: Ei 3105RF (OPTICAL WITH HUSH) Ei 3100RF (IONISATION) P/N B15??? Rev 0

IMPORTANT Additional Instructions for the Radio Interconnect Heat Alarm Ei3103RF The Ei3103RF Heat Alarm, usually located in the kitchen, must be used with Smoke Alarms Ei3100RF and/or Ei3105RF located on the escape route from the house. The Radio Interconnect will help ensure the alarm is heard through-out the house as all units will alarm, if one senses fire. 1. For Location & Positioning see section 2 & 3 of the main instructions. 2. Pull cover open at tab. 3. Place the base on ceiling or wall exactly where you want to mount the unit. With a pencil, mark the location of the screw holes. 4. Taking care to avoid any electrical wiring in the ceiling or wall, drill a hole through the centres of the marked locations. Push the plastic Screw Anchors provided into the drilled holes. Screw in firmly. 5. Connect the battery and close the cover. 6. The Radio Wireless interconnect will now operate. Pressing the test button on one unit should cause all the others to alarm. (All alarms are set in default factory mode and will communicate with each other). Installing your Heat Alarms 7. However we strongly recommend that you house code yo alarms to prevent your units setting off your neighbour’s alarms vice versa. To house code all your alarms: 7.1 Open the cover by pulling the tab. 7.2 Press the house code switch (see figure 3a) and hold until th amber light comes on, then release the switch. The amber light w then flash rapidly for about 1 second to indicate it is now in hous code mode. Leave the cover hanging open. 7.3 Now similarly press the house code switches on all the rest the alarms, within 15 minutes, to put them also into house cod mode. (The alarms automatically come out of house code mod after 15 minutes). 7.4 When in house code mode, the amber light will flash a numb of times every 5 seconds, to indicate the number of alarms that hav been identified as part of your system. For example with 3 alarms your system, you should see 3 amber flashes every 5 seconds. 7.5 Check that the number of amber light flashes (on each alarm corresponds to the number of units in the system. If this is not th case repeat the house code procedure. If there is still a proble rotate or re-locate the units and then house code the units again their final position. 7.6 Close the covers on all the units. Radio Interconnect Heat Alarm Ei3103RF Note: (i) The Ei3103RF model does not have a hush button. If there is nuisance alarm, fan cooking fumes etc. away from unit with newspaper or similar. (ii) The Ei3103RF cannot be made into a repeater. (If you think you need a repeater purchase an Ei Electronics Optic Smoke Alarm Ei3105RF. (A repeater ‘repeats’ the RF signal increase the range). (iii) When the test button is pressed the RF interconnection can b checked by listening for the other units sounding. (The test button may need to be held for up to 10 seconds for the R message to be sent). If you need clarification contact us at th details below. P/N A16336 Rev2 “OPEN HERE” TAB HINGES WRITE IN DATE BATTERY INSTALED SCREW HOLE SCREW HOLE HOUSE CODE SWITCH RF SIGNAL AMBER LIGHT PLASTIC CLIP BATTERY CONNECTION BATTERY HOLDER COVER Figure 3 Ei Electronics Shannon, Co. Clare, Ireland Tel: +353 (0)61 471277 visit us at www.eielectronics.com