EMC D860 Archiver Manuals

All plug-in modules and blank plates are part of the fire enclosure and must be removed only when a replacement can be added immediately. The system must not be run without all parts in place. 4 A controller or a shelf must be operated only from a power supply input voltage range of 100–240 VAC, 50–60 Hz. 4 Each component is intended to operate with two working power supplies installed. 4 Provide a suitable power source with electrical overload protection. 4 A safe electrical earth connection must be pro- vided to the power cord. Check the grounding of the power sources before applying power. 4 The plug on each power supply cord is used as the main disconnect device. Ensure that the socket outlets are located near the equipment and are easily accessible. 4 Permanently unplug the unit if you think it is damaged in any way and before moving it. If the unit is powered by multiple sources, discon- nect all supplied power for complete isolation. 4 The power connections must always be disconnected prior to removal or replacement of a power supply module from any of the components in the system. 4 A faulty power supply module must be replaced within 24 hours. 4 Do not lift system components by yourself. A controller weighs up to 52 lbs (23.6 kg) and an expansion shelf weighs up to 78 lbs (35.5 kg). 4 Do not lift an expansion shelf by the handles on any modules. The handles are not designed to support the weight of the populated shelf. 4 To comply with applicable safety, emission, and thermal requirements, covers must not be removed and all bays must be fitted with plug-in modules. 4 Load the rack beginning at the bottom to prevent the rack from becoming top-heavy. 4 Do not extend components on slide rails until you have loaded at least three or more similarly weighted items in the rack, or unless the rack is bolted to the floor or overhead structure to prevent tipping. Caution: If the system is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. Caution: The RJ45 sockets on the motherboard/PCI cards are for Ethernet connection only and must not be connected to a telecommunications network. ESD Precautions Data Domain recommends that you fit and check a suitable antistatic wrist or ankle strap and observe all conventional ESD precautions when handling plug-in modules and components. Safety The steps for a complete installation and configuration are: 1. Install hardware 2. Define the Data Domain system information for your site 3. Perform initial system configuration 4. Configure the system for data access 5. Configure optional software 6. Perform optional additional system configuration Installation and Setup Steps 1 5 4 3 2 6 Installation and Setup Guide EMC DATA DOMAIN DD860 Archiver Storage System 1. Unpack the Data Domain system. A system consists of a DD860 Archiver controller and up to 768 TB of raw storage in optional expan- sion shelves. 4 Open the packing boxes for the controller and optional expansion shelf or shelves. 4 Remove the accessories and rack mount kits for all system components. 2. Install the appropriate rack mounting hardware for the controller and expansion shelves into a 19-inch, four-post rack. Ensure that the rack is securely anchored to prevent tipping. Load the rack or cabinet beginning at the bottom to prevent the rack from becoming top-heavy. Be sure to plan appropriate vertical space to accommodate the 2U controller and 3U for each expansion shelf. 4 See the instructions included with the slide rails. 4 The expansion shelf rails also include rack installation instructions. 3. Install the controller and expansion shelves in the rack. 4 Remove the controller and expansion shelves from the shipping boxes. 4 Remove the bezel from each component. 4 Install each component horizontally on the corresponding rails and slide into the rack in the order described in the Expansion Shelf Hardware Guide. Be sure one person is at each side of each compo- nent for proper and safe installation. 4 Secure the components in the rack; see respective hardware manual. 4. Connect expansion shelves to the controller. Connect the controller’s SAS ports to the expansion shelves based on the cabling diagrams for expansion shelf connectivity. See Figures 5 or 6. Use the Cable Management Bar and Velcro strips to support and organize all cables. 5. Connect an administrative console. Attach a serial console to the controller’s serial port; or use KVM connections to connect monitor (VGA port), keyboard and mouse. See Figure 1. 6. Enable data transfer connectivity. Repeat for each connection. 4 Ethernet connection: If using 1 Gb copper Ethernet, attach a Cat 5e or Cat 6 copper Ethernet cable to an RJ45 Ethernet network port (start with eth0a and go up) on the controller, and attach the other end to an Ethernet switch or to an Ethernet port on your server. If using 1 Gb fiber Ethernet, use multimode fiber cables with LC connectors. If using 10 Gb copper Ethernet with an SFP+ connector, use a qualified SFP+ copper cable. If using 10 Gb fiber Ethernet, use MMF-850nm cables with LC duplex connectors. See Figure 1. 7. Provide redundant power to the system. 4 Controller power: Connect power cables to both receptacles. See Figure 1. On each cable, attach the cable restraint tie. 4 Expansion shelf power: Connect power cables to both receptacles and attach the power cable retention clips. See Figure 4. 8. Turn the system on. Power on any expansion shelves before the controller. The ES30 powers on when plugged in. 4 ES20 power: Turn the power switch to on for each of the two power supplies for each ES20 shelf. See Figure 3. 4 Wait approximately 3 minutes after all expansion shelves are turned on. 4 Controller power: Push the power button. See Figure 2. 4 Attach the bezels. 9. Collect the information needed for installation. Record the information in Section 2 of this document. Install Hardware 1