Fike 55-043 Manuals

D500-73-00 1 I56-2462-02 704 South 10th Street, Blue Springs, MO 64015 (816) 229-3405 www.fike.com INSTALLATION INSTRUCTIONS 55-043 Relay Module SPECIFICATIONS Normal Operating Voltage: 15 to 30 VDC Standby Current: 500 µA max. average (continuous broadcasts) Alarm Current: 2.0 mA (red LED on) Short Circuit Current Dry Control Input: 30 µA max. Avg. (5 VDC) Maximum Resistance Dry Contact Input: 100 Ω Temperature Range: 32°F to 120°F (0°C to 49°C) Humidity: 10 to 93% RH Noncondensing Dimensions: 4.17ʺH × 4.26ʺW × 1.22ʺD (106mm H × 108mm W × 31mm D) Accessories: Wall cover plate (included) SMB500 Surface Mount Electrical Box EA-CB Control Module Barrier BEFORE INSTALLING This information is included as a quick reference installation guide. Refer to the appropriate control panel installation manual for detailed system information. If the modules will be installed in an existing operational system, inform the operator and local authority that the system will be temporarily out of service. NOTICE: This manual should be left with the owner/user of this equipment. GENERAL DESCRIPTION Relay Module, Model 55-043, is to be designed for use in acti- vation of the types of products that are generally connected to an intelligent fire alarm system. It provides two sets of form C contacts that switch together (one DPDT relay). There is also an input that is capable of monitoring a dry set of contacts for open or closed conditions. COMPATIBILITY REQUIREMENTS To ensure proper operation, this module shall be connected to a listed compatible control panel. LED INDICAT OR IR RECEIVER C0166-00 CURRENT RATING MAXIMUM VOLTAGE LOAD DESCRIPTION APPLICATION 3A 30 VDC RESISTIVE NON-CODED 2A 30 VDC RESISTIVE CODED 1A 30 VDC INDUCTIVE (L/R = 2 ms) CODED 0.5A 30 VDC INDUCTIVE (L/R = 5 ms) CODED 0.9A 70.7 VAC RESISTIVE NON-CODED 0.7A 70.7 VAC INDUCTIVE (PF = 0.35) NON-CODED NOTE: This module is not approved for use in the European Union, at or above 50VAC or 70VDC. MOUNTING The module mounts directly to 4ʺ square electrical boxes. The box must have a minimum depth of 21⁄8ʺ. Modules must be mounted with the arrow facing upward for proper operation of the IR pro- gramming tool. Surface mounted electrical boxes (SMB500) are available from Fike. FROM PANEL OR PREVIOUS PANEL (–) (+) COMMUNICATION LINE 30 VDC MAX. TWISTED PAIR RECOMMENDED COMMUNICATION LINE IS SUPERVISED AND POWER LIMITED (–) (+) (–) (+) (–) (+) 1 2 3 4 TO NEXT DEVICE 5 6 12 11 10 9 8 7{ RELAY CONTACTS NORMALLY OPEN OR NORMALLY CLOSED CONTACT DEVICE (NOT SUPERVISED) NOTE: NORMALLY CLOSED OPTION MAY NOT BE USED FOR FIRE APPLICATIONS. CONNECT MODULES TO LISTED COMPATIBLE CONTROL PANELS ONLY NORMALLY OPEN (T12) COMMON (T11) NORMALLY CLOSED (T10) NORMALLY OPEN (T9) COMMON (T8) NORMALLY CLOSED (T7) RELAY CONTACT #2 RELAY CONTACT #1 MODULE DOES NOT SUPERVISE CONTROLLED CIRCUITS. TERMINALS 1-6 ARE POWER LIMITED. TERMINALS 7-12 ARE NON-POWER LIMITED. WIRING NOTE: All wiring must conform to applicable local codes, ordi- nances, and regulations. 1. Install module wiring in accordance with the job drawings and appropriate wiring diagrams. NOTE: Separate cable entry openings must be used to maintain required spacing between power limited and non-power limited wiring. Optional EA-CB may be required to sepa- rate power limited and non power limited wiring in the electrical box. 2. Set the address on the module per job drawings using the IR configuration tool (model no. EA-CT). 3. Secure module to electrical box (supplied by installer). This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. FCC Statement D500-73-00 2 I56-2462-02 ©2004 Fike Figure 2: Wiring Diagram C0110-01 TERMINAL DEFINITIONS T1 (+) SLC in/out T7 Normally Closed #1 T2 (–) SLC in/out T8 Common #1 T3 (+) SLC in/out T9 Normally Open #1 T4 (–) SLC in/out T10 Normally Closed #2 T5 (+) Dry Contact Input T11 Common #2 T6 (–) Dry Contact Input T12 Normally Open #2 WARNING All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state dur- ing shipping. To ensure that the switch contacts are in their cor- rect state, modules must be made to communicate with the panel before connecting circuits controlled by the module.