Gianni DG-160 Manuals

DG-160 DG-800 Stand Alone Reader Operation Manual Specifications Note: 1. It is suggested to use a linear power supply unit to prevent reading range reduction at the card reader. 2. It is suggested to use #22~26 AWG insulation wire. 3. Exit button is at N.O. contact. 4. With CE qualification EMC specification. 5. The door strike or relay must have a varistor or a diode across the door strike terminals to suppress the back EMF of the strike – failure to do so will damage the relay contacts and electronic components, or even burns the controller. Warranty: The product is warranted against defects in material and workmanship while used in normal service for a period of 1 year from the date of sale to the original customer. The GEM policy is one of continual development and improvement; therefore GEM reserves the right to change specifica- tions without notice. For AC/DC For DC use only Wiring Diagram Features 1. Memory volume up to 1000+10 proximity cards/tokens and PINs with the programming time up to 0.5 second. 2. Access modes: a. Only Proximity Card (default setting) b. PIN or Proximity Card c. PIN + Proximity Card 3. Logical memory prevents duplicated card setting. 4. Lockout Function: The controller will lockout for 60 seconds after entering 5 times invalid PINs or unsuccessful card attempts. (The keypad without beep during the period time). 5. Controller with keypad sound to avoid incorrect key-in. 6. Additional input for anti-tailgating function to ensure high security access control. 7. Built-in tamper switch. 8. Non-volatile memory stores all code settings for a long time, even in the event of total power failure. 9. Dual relays to control door lock and other security devices. 10. Aluminum alloy casing designed with vandal resistant screws for enhanced safety and durability. 11. Slim type keypad design (DG-160). 12. Epoxy sealed for waterproof. Indicator Status & Default Setting Parameters Factory Default Setting: Access Mode Proximity Card Only Format All Bits Card Storage (MAX. 1000+10 pcs) None Master Code 12345 (5 digits) Alarm Function (All) Function disabled Relay Strike Time (Time Delay Setting) 1 second Pressed Key Time Delay 5 seconds (Fixed) PIN Code Input Waiting Time 5 seconds Programming Mode Time Delay 30 seconds (Fixed) Beep & LED Indication: Mode Signal Status Right Green Stay On Power on, Standby Green On First relay active Standby Red On Second relay active Yellow Stay On Enter programming mode Green Stay On Red Stay On The slot position of first relay is available. The slot position of first relay is unavailable. LED Programming Green Stay On Red Stay On The slot position of second relay is available. The slot position of second relay is unavailable. 1 Beep Valid card, key press, enter programming mode Standby 3 Beeps Invalid card, incorrect PIN 1 Beep Correct Input data, Exit programming mode Beep Programming 3 Beeps Incorrect Input data, other incorrect operation, duplicated card setting 12VDC + 12VDC + + + N.C.1 COM1 N.O.1 PB1 PB2 REED N.C.2 COM2 N.O.2 GND + + Power Supply Unit Power Supply Unit Varistor Electric Lock 1 Fail-Safe Mode (MUST install a Varistor) (MUST install a Diode) REED Electric Lock 2 Fail-Secure Mode Door Closed=N.O. Door Opened=N.C. Exit Button1 Exit Button 2 Stand Alone Reader Red Black Light Green Pink White Orange Yellow Brown Gray Purple Blue Green N.C.1 COM1 COM2 N.O.1 N.O.2 PB1 PB2 REED N.C.2 GND + Operating Voltage 12VDC Current Draw DG-800 (Pull In: 90mA/12VDC, Holding: 30mA/12VDC) DG-160 (Pull In: 110mA/12VDC, Holding: 50mA/12VDC) RF Frequency EM 125KHz Read Range 5 cm (In noise-free environment) Keypad Backlit 12-digit (0~9,＊,#) Input Output 2 contacts for Request-To-Exit button 1 contact for door reed switch 2 relays (Dry contacts: N.O./N.C./Com.) LED Status Indication 2 LED indicators display (Red/Green) Memory Volume 1000+10 proximity cards/tokens and PINs Relay Electric Current Max. 2A/30VDC, 0.6A/120VAC Relay Strike Time 01~99 seconds or Toggle Mode (00) Ambient Humidity 5%~95% (Non-condensing) Operating Temperature -20°C~70°C 76 120 20.5 DG-800 DG-160 24 44 151.5

1. Memory volume up to 1000+10 proximity cards/tokens and PINs. Reading time approx. 0.5 seconds. 2. Access modes: a. Only Proximity Card b. PIN or Proximity Card (default setting) c. PIN + Proximity Card 3. Logical memory prevents duplicated card setting. 4. Lockout Function: The controller will lockout for 60 seconds after entering invalid PINs or reading invalid cards for 5 times. (The keypad doesn’t beep during the period of time). 5. Controller with keypad sound to avoid incorrect key-in. 6. Additional input for anti-tailgating function to ensure high security access control. 7. Built-in anti-tamper switch. 8. Non-volatile memory stores all code settings, even in the event of total power failure or controller not in use for a long time. 9. Dual relays to control door lock and other security devices. 10. Aluminum alloy casing with vandal resistant screws for enhanced safety and durability. 11. Epoxy sealed for waterproof. 12. Slim-type keypad design for narrow door-frames (DG-160). EM 125KHz 5 cm (In noise-free environment) Backlight 12-digit (0~9,＊,#) Relay Rating All LEDs Stay On Right Green Stay On Red Stay On Valid card, press key, enter programming mode Diode 12~24VAC/DC DG-160: Pull In:60mA/12VDC,Holding:40mA/12VDC Pull In:30mA/24VDC,Holding:20mA/24VDC DG-800: Pull In:100mA/12VDC,Holding:70mA/12VDC Pull In:50mA/24VDC,Holding:35mA/24VDC Max.2A/30VDC ; 0.6A/120VAC 1234 (4 digits) Master Code Relay Strike Time (Time Delay Setting) Pressed Key Time Delay PIN Code Input Waiting Time Programming Mode Time Delay Card Storage (MAX. 1000+10pcs) Format Access Mode PIN or Proximity Card All Bits None 1 second 5 seconds (Fixed) 5 seconds 30 seconds (Fixed)