Hakko Electronics FX-888D Manuals

Cleaning wire HAKKO FX-888D Station HAKKO FX-8801 Soldering iron Iron holder Instruction Manual Warnings, cautions and notes are placed at critical points in this manual to direct the operator’s attention to significant items. They are defined as follows: WARNING A. Setup the iron holder 1. Fit the small sponge pieces into the hollows of the iron holder base. 2. Add an appropriate amount of water into the iron holder base. The small sponge will absorb water to keep the wet state at all times. 3. Dampen the large sponge and place it on the iron holder base. *When using a Cleaning Wire Place it in the bottom plate as shown on the right. See "2.Using a Cleaning Wire" in section "6. MAINTENANCE" 1 1 1 1 1 ● Operation and indication Switch and control button The front panel for HAKKO FX-888D has the following two control buttons. －Use this button to select and change settings. In the temperature preset mode, pressing this button will change the selected preset temperature while the unit is in operation. Pressing and holding the button will start the adjustment mode. －Use this button to make and confirm selections. Pressing this button will display the current set temperature. Pressing and holding the button will start the temperature setting mode. ENTER UP ■ Making Changes to Settings ENTER Instruction Manual 1. PACKING LIST AND PART NAMES Please check to make sure that all items listed below are included in the package. *HAKKO FX-8802 / FX-8803 / FX-8804 (not included) can be connected to HAKKO FX-888D station. *When using above HAKKO FX-8802/FX-8803/FX-8804, please use it with the applicable iron holder. This product includes such features as electrically conductive plastic parts and grounding of the unit as measures to protect the device to be soldered from the effects of static electricity. Be sure to observe the following instructions: 1. The plastic parts are not insulators, they are conductors. When making repairs or replacing parts, take sufficient care not to expose live electrical parts or damage insulation materials. 2. Be sure to ground the unit during use. ■ Electrostatic Protection When power is ON, tip temperatures will be between 200 and 480℃. (400 to 899℉) To avoid injury or damage to personnel and items in the work area, observe the following: ● Do not touch the tip or the metal parts near the tip. ● Do not allow the tip to come close to, or touch, flammable materials. ● Inform others in the area that the unit is hot and should not be touched. ● Turn the power off when not in use, or left unattended. ● Turn the power off when changing parts or storing the HAKKO FX-888D. ● This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. ● Children should be supervised to ensure that they do not play with the appliance. ● If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid personal injury or damage to the unit. ● The unit is for a counter or workbench use only. A. Turn on the power switch After turning on the power switch, will be displayed for two seconds, and current temperature will be displayed. When the display stabilizes, LED heater lamp will begin to flash. B. After use Always clean the tip and coat it with fresh solder after use. Hold down the button for at least one second. 5. OPERATION 4.INITIAL SETUP Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved. Two examples are given below. Failure to comply with a WARNING may result in serious injury or death. WARNING: CAUTION : HAKKO FX-8801 Cord assembly Iron holder Cleaning sponge Iron holder base HAKKO FX-888D Station Power switch OFF ON Cleaning wire Copyright © 2012 HAKKO Corporation. All Rights Reserved. 5. OPERATION CAUTION Small sponge pieces Large sponge Receptacle UP ENTER FX-888D Thank you for purchasing HAKKO FX-888D soldering station. Please read this manual before operating the HAKKO FX-888D. Keep this manual readily accessible for reference. Iron receptacle AC26V 65W < 2 Ω < 2 mV Ceramic heater 1.2m (3.9 ft.) 217mm (8.5 in.) with B tip 46g (0.10 lb. / 1.62 oz.) with B tip Power consumption 70W ● Station * The temperature was measured using the FG-100 thermometer. * This product is protected against electrostatic discharge. * Specifications and design are subject to charge without notice. ● HAKKO FX-8801 Soldering iron Power consumption Tip to ground resistance Tip to ground potential Heating element Cord Total length (w/o cord) Weight (w/o cord) Instruction manual in the language of Japanese, English, Chinse, French, German and Korean can be downloaded from the HAKKO Document Portal. (Please note that some languages may not be available depending on the product.) 2. SPECIFICATIONS 3. WARNINGS, CAUTIONS AND NOTES ● To prevent accidents or damage to the HAKKO FX-888D, be sure to observe the following: ● Do not use the HAKKO FX-888D for applications other than soldering. ● Do not strike the iron against hard objects to remove excess solder. This will damage the iron. ● Do not modify the HAKKO FX-888D. ● Use only genuine Hakko replacement parts. ● Do not allow the HAKKO FX-888D to become wet, or use it with wet hands. ● Remove power and iron cords by holding the plug. not the wires. ● Be sure the work area is well ventilated. Soldering produces smoke. ● While using HAKKO FX-888D, don’t do anything which may cause bodily harm or physical damage. CAUTION Be sure the sponge is moistened with water before use to avoid damaging the tip. If no buttons are pressed for at least one minute during the process of changing settings of the unit, the system will exit and return to operating mode and display the current temperature. ● Changing the set temperature There are two ways to change the setting temperature : normal mode or preset mode. The temperature setting range is from 200 to 480℃. (from 400 to 899℉) By default, the temperature is set to 350℃. (662℉) ● The normal mode Example : Changing from 350℃ to 400℃ The desired temperature is saved to the system memory. Heater control will begin after the new set temperature is displayed. UP Press the button once. ENTER Press the button once. UP Press the button five times. ENTER Press the button once. ENTER Press the button once. ● The preset mode The HAKKO FX-888D has a preset mode that will allow the unit to store up to 5 preset temperatures you can change between instead of using the above normal mode. Initial preset temperatures The initial number of active presets is set to 5 at the factory. The default selected preset is set to P3 at the factory. Example : Changing preset temperature from preset No.1(250℃) to No.3(350℃). UP Press the button once. UP Press the button twice. ENTER Press the button once. *Preset selection screen Be displayed alternately. Be displayed alternately. Heater control will begin with new preset temperature. The procedure for making changes to the preset temperatures is the same as changing the set temperature in normal mode. Place the iron in the iron holder when not in use. Turn the power off when the HAKKO FX-888D is not in use for extended period. CAUTION Output Temperature range Temperature stability Dimensions (W × H × D) Weight (w/o cord) AC26V 200 - 480℃ (400 - 899℉) ±1℃ (±1.8℉) at idle temperature 100(W) × 120(H) × 120(D) mm (3.9 × 4.7 × 4.7 in.) 1.2kg (2.6 lb.) : 250℃ (482℉) : 300℃ (572℉) : 350℃ (662℉) : 400℃ (752℉) : 450℃ (842℉) LED heater lamp Push on the plug until it stops, making sure it is securely connected. Receptacle To disconnect, hold the plug and pull it out of the receptacle. B. Connect the iron to the station 1. Connect the cord assembly to the receptacle. 2. Place the iron into the iron holder. 3. Plug the power cord into an appropriate power supply. CAUTION Be sure to turn off the power before connecting or disconnecting the cord assembly for the iron to and from the receptacle to avoid damaging the circuit board. CAUTION Do not use any iron other than those listed in Section 1 of this manual. Doing so may result in inadequate performance and / or possible damage to the unit. CAUTION The unit is protected against electrostatic discharge and must be grounded for full efficiency. 2012.5 MA02469XZ120517

Cleaning wire HAKKO FX-888D Station HAKKO FX-8801 Soldering iron Iron holder (with cleaning sponge) Instruction Manual 1 1 1 1 1 Instruction Manual 1. PACKING LIST AND PART NAMES Please check to make sure that all items listed below are included in the package. *HAKKO FX-8802 / FX-8803 / FX-8804 (not included) can be connected to HAKKO FX-888D station. *When using the HAKKO FX-8802/FX-8803/FX-8804, please use it with the applicable iron holder. HAKKO FX-8801 Cord assembly Iron holder Cleaning sponge Iron holder base HAKKO FX-888D Station Power switch OFF ON Cleaning wire Receptacle Thank you for purchasing the HAKKO FX-888D soldering station. Please read this manual before operating the HAKKO FX-888D. Keep this manual readily accessible for reference. Iron receptacle This product includes such features as electrically conductive plastic parts and grounding of the unit as measures to protect the device to be soldered from the effects of static electricity. Be sure to observe the following instructions: 1. The plastic parts are not insulators, they are conductors. When making repairs or replacing parts, take sufficient care not to expose live electrical parts or damage insulation materials. 2. Be sure to ground the unit during use. ■ Electrostatic Protection 65W (26V) < 2 Ω < 2 mV Ceramic heater 3.9 ft. (1.2m) 8.5 in. (217mm) with 1.6D tip 0.10 lb. (46g / 1.62 oz.) with 1.6D tip Power consumption 70W ● Station * The temperature was measured using the FG-100 thermometer. * This product is protected against electrostatic discharge. * Specifications and design are subject to charge without notice. ● HAKKO FX-8801 Soldering iron Power consumption Tip to ground resistance Tip to ground potential Heating element Cord length Total length (w/o cord) Weight (w/o cord) 2. SPECIFICATIONS Output voltage Temperature range Temperature stability Dimensions (W × H × D) Weight (w/o cord) AC 26V 400 - 899℉ (200 - 480℃) ±1.8℉ (±1℃) at idle temperature 3.9(W) × 4.7(H) × 4.7(D) in. (100 × 120 × 120 mm) 2.6 lb. (1.2kg)

Soldering iron • Digital model in an analog-model price bracket • Features adjustment mode, preset mode, and password function • Separable tip/heater design provides excellent value for money • Supports the N2 system. Model No. FX888D Power consumption 70W Temperature range 200-480ºC Temperature stability ±1ºC at idle temperature ・Station Output voltage AC 26V Dimensions 100(W)×120(H)×120(D)mm Weight 1.2kg ・Soldering Iron Power consumption 65W (26V) Tip to ground resistance <2Ω Tip to ground potential <2mV Standard tip Shape-B (No.T18-B) Heating element Ceramic heater Cord length 1.2m Total length 217mm (with B tip) Weight 46g (with B tip) * Length and weight (w/o cord)

FX-888D settings and adjustments The FX-888D has 4 Parameter settings (see section 6. Parameter Setting in the Instruction Manual). For reasons that only make sense to the engineer that programmed the software, the parameters are numbered 01, 03, 11, and 14. The parameter settings are very rarely changed from the factory settings. If you change a parameter setting it would be even ra station and would not typically be adjusted. Parameter 01: Allows you to display the temperature in Celsius or Fahrenheit. The station is factory set to display the temperature in Fahrenheit. Parameter 03: Low temperature error setting allows you to set there is a drop in the tip temperature beyond the Low Temperature Alarm Setting. The station comes from the factory with a Low Temperature Alarm Setting station at 750ºF and the measured tip temperature dropped to 480ºF (750 error. I recommend you leave the Low Temperature Alarm at the factory setting and watch the solder flow, which is a better indication of how the heat is transferring to the solder connection. Parameter 11: Allows you to switch between control. The station comes from the factory set to normal mode. Normal mode al soldering station to any temperature between 120 so that whenever you turn on the station it will heat to the last temperature you were using. Preset mode allows you to “preset” from 2 to 5 temperatures. Preset mode is only useful if you constantly change between specific temperatures when soldering. It gives you a faster way to adjust between specific temperatures. Most operators would not need to use preset mode. If you change to p mode you must also enter the number of preset channels (2 leaving the station in normal mode. Parameter 14: Password setting allows you to enter a Password to restrict the ability of someone to adjust the station without a password. This feature is sometimes used by large assembly lines that want to control the soldering temperature process. They would enter a password and not give the password to the operator. The operator would be unable to change the temperatu password setting from the factory is Open, which means there is no password 888D settings and adjustments 888D has 4 Parameter settings (see section 6. Parameter Setting in the Instruction For reasons that only make sense to the engineer that programmed the software, the parameters are numbered 01, 03, 11, and 14. The parameter settings are very rarely changed from the factory settings. If you change a parameter setting it would be even rarer to change it back. These are the core setting of the station and would not typically be adjusted. : Allows you to display the temperature in Celsius or Fahrenheit. The station is factory set to display the temperature in Fahrenheit. : Low temperature error setting allows you to set the station to display an error message if there is a drop in the tip temperature beyond the Low Temperature Alarm Setting. The station comes from the factory with a Low Temperature Alarm Setting of 270ºF. In this case, if you were using the station at 750ºF and the measured tip temperature dropped to 480ºF (750-270), the display will flash an error. I recommend you leave the Low Temperature Alarm at the factory setting and watch the solder hich is a better indication of how the heat is transferring to the solder connection. : Allows you to switch between “normal mode” and “preset mode” of temperature control. The station comes from the factory set to normal mode. Normal mode allows you to adjust the soldering station to any temperature between 120-899ºF. The last set temperature is stored in memory so that whenever you turn on the station it will heat to the last temperature you were using. Preset m 2 to 5 temperatures. Preset mode is only useful if you constantly change between specific temperatures when soldering. It gives you a faster way to adjust between specific temperatures. Most operators would not need to use preset mode. If you change to p mode you must also enter the number of preset channels (2-5) you will want to have. I recommend leaving the station in normal mode. : Password setting allows you to enter a Password to restrict the ability of someone to n without a password. This feature is sometimes used by large assembly lines that want to control the soldering temperature process. They would enter a password and not give the password to the operator. The operator would be unable to change the temperature without the password. The password setting from the factory is Open, which means there is no password needed to adjust the 888D has 4 Parameter settings (see section 6. Parameter Setting in the Instruction For reasons that only make sense to the engineer that programmed the software, the The parameter settings are very rarely changed from the factory settings. If you change a rer to change it back. These are the core setting of the : Allows you to display the temperature in Celsius or Fahrenheit. The station is factory set the station to display an error message if there is a drop in the tip temperature beyond the Low Temperature Alarm Setting. The station comes of 270ºF. In this case, if you were using the 270), the display will flash an error. I recommend you leave the Low Temperature Alarm at the factory setting and watch the solder hich is a better indication of how the heat is transferring to the solder connection. “normal mode” and “preset mode” of temperature lows you to adjust the 899ºF. The last set temperature is stored in memory so that whenever you turn on the station it will heat to the last temperature you were using. Preset m 2 to 5 temperatures. Preset mode is only useful if you constantly change between specific temperatures when soldering. It gives you a faster way to adjust between specific temperatures. Most operators would not need to use preset mode. If you change to preset 5) you will want to have. I recommend : Password setting allows you to enter a Password to restrict the ability of someone to n without a password. This feature is sometimes used by large assembly lines that want to control the soldering temperature process. They would enter a password and not give the password re without the password. The needed to adjust the