Honeywell AlarmNet 7845i-GSM Manuals

7845GSM / 7845i-GSM QUICK GUIDE for “C” Series Replacement and New Installations K14324V1 8/06 Rev. B Copyright 2006 Honeywell International Inc. 165 Eileen Way, Syosset, New York 11791 This guide explains how to install a 7845GSM or 7845iGSM for basic ECP mode applications primarily intended to replace "C" series modules. This guide can also be used by experienced installers for new 7845GSM/7845i-GSM installations. Abbreviated programming and registration procedures also provided. Programming assumes module's default values will be used. See Installation Guide for values. Connect 7720P to Module. Exit Program Mode by pressing "Shift -ESC," then press "N" at the Review prompt, then press "Shift -Y" at the "EXIT PROG MODE?" prompt. Go to "PRIMARY SUB ID" prompt and enter ID. (provided by CS) Go to "PRIMARY CS ID" prompt and enter ID. (provided by CS) Scroll (Using Up/Down Arrows) to "PRIMARY CITY ID" prompt and enter ID. (provided by CS) Enter Program Mode by pressing [ # ], then "Shift -Y" at the "START PROGRAM MODE" prompt. Go to "DEVICE MODE" prompt and confirm module is in "ECP" Device Mode. (Refer to the Installation and Setup Guide if using any other mode.) Honeywell's AlarmNet Direct PROGRAMMING AND REGISTERING THE MODULE WITH THE 7720P A. B. C. D. E. F. G. For new 7845GSM/7845i-GSM: Register Module by pressing Shift - [ ] Up Arrow key. Disconnect the 7720P and install module cover (use cover securing screw for UL installations). Wait for the "Registration Success" message to appear. The unit is registered and available for alarm reporting. Refer to the Installation and Setup Guide if any error messages are displayed. A. B. You can also register the module by calling the AlarmNet Technical Assistance Center (TAC) at 1-800-222-6525. You will need the following information: · MAC number (found on the label). · Subscriber information (provided by the central station), including a city code, CSID, and a subscriber ID. When instructed to do so, triple-click the tamper switch to complete the registration. COMMAND FUNCTION Shift - [D] Shift - [C] Shift - [F] Shift - [X] Shift - [ ] Shift - [T] Shift - [S] Shift - [E] Shift - [B] Shift - [A] Software Revision (month, day, year) MAC Address, SCID, and IMEI Displays Time (GMT from AlarmNet network) Network Diagnostics Display (internet status) System Status (faults, battery, line voltage) GSM Status Display Screens (radio status) Network Diagnostic Test Test Alarm (for registered modules only) Reset the module (UP arrow) Registration for new installation (DN arrow) Registration with PIN for Replacement [ ] [ENTER] Enter Program Mode PROGRAMMER KEYBOARD COMMANDS ("D" and "F" apply to 7845i-GSM only) NOTES: A. AlarmNet-I Account: The 7845GSM and 7845i-GSM modules require an AlarmNet–I account. For new installations, please obtain the account information from the central station prior to programming this module. For replacement installations, the AlarmNet-I account is created automatically when the module is registered (based on the existing "C" series account). B. For Replacement Installations Check the existing device for its current mode and programming options prior to replacing. Do not use the existing “C” radio’s antenna. (AMPS antenna is not compatible with this module). · · · · · By 7720P: See procedure below. By Phone (registration only): See below. Registering by Phone: Registering If replacing a "C" series module: Register Replacement Module by pressing [ ] Down Arrow key, Then enter PIN Number (last four digits of old module's MIN number) and press Enter. OR For a replacement module, an alarm message (00D0 010B 0) will be sent to the central station indicating the "C" series module has been replaced. C. ����������� By AlarmNet Direct Website: GO TO: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx Log in and follow the on-screen prompts. See "Honeywell's Alarmnet Direct" section on back. This product can now be programmed and registered through the Alarmnet Direct Website, which is a powerful web-based solution that provides our customers with a communication link to AlarmNet devices and services. To program and register the module via the website (if you are already signed up for this service), please go to: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx. Log in and follow the on-screen prompts. For purposes of validation, please have the following information available when programming the module: 1. Primary City ID (two-digit number) 2. Primary Central Station ID (two-digit hexadecimal number) 3. Primary Subscriber ID (four-digit number) 4. MAC ID and MAC CRC number (located on outside of box and on label inside module) or Min Number of the device you’re replacing 5. Mode of operation of existing radio if replacing a “C” series radio. Dealer Sign-Up If you are not signed up for this service, click on “Dealer Sign-Up” from the login screen to gain access to our web-based programming of Honeywell's 7845GSM/7845i-GSM and next generation communication devices. Dealer Sign-Up Direct Link: https://services.alarmnet.com/AlarmNetDirectP_SignUp. You will be instructed how to proceed and a login will be created upon completing the sign-up form. Only one sign-up per dealer is required. Once an initial user is established, additional logins may be created by that user. NOTE: Central Stations sign up by contacting AlarmNet Administration at 800-222-6525 option 3. Programming and Registration Programming (WHEN USING ECP MODE ONLY)

trength 1C 3C 3C available AC source at least 3-5 bars lit ction LED Display Step Power Up and Program 4 Plug in transformer to a 120V AC source Power up control panel Check that module is in ECP mode. Press and hold RSSI/Mode status switch. Red LED and both Yellow LEDs should be off. (Refer to Installation and Setup Guide if using any other mode) Use the web-based programming tool on the AlarmNet Direct website or the 7720P Programmer to complete programming (see Installation and Setup Guide for instructions) hernet port to router – the Ethernet ight-most LED is lit in the network ase back he right side of the case back and screw provided have been made, connect battery als nnector J1 Step Register 5 All Honeywell GSM modules are pre-activated with the cellular carrier The GSM module requires an AlarmNet-i account and may be registered by one of the following methods: – Via web-based programming on https://services.alarmnet.com/alarmnetdirect – Via 7720P Programmer – By calling AlarmNet Technical Assistance at 1-800-222-6525 When replacing 7845C series modules, registration may be done by entering a PIN number See Installation and Setup Guide for complete instructions 7845i-GSM shown at actual size G Y G G R Y OFF OFF RSSI/Mode Status Indicator Switch 1A Zone 6 Input Zone 7 Input Fault Output to Panel Zone Input Connection for 7720P Programmer EOLR AC Transformer Internal antenna Tamper switch Connector J1 for LEDs: Status (green) Message (yellow) Fault (red) or 7845GSM/7845i-GSM Modules MOUNTING SCREW (4) (TYP) G CASE FRONT E K A B C D 3A 3B 4B 4C Control ECP Terminals

K14441 8/06 Rev. A AlarmNet AlarmNet AlarmNet AlarmNet GSM GSM GSM GSM----ANT ANT ANT ANT3dB 3dB 3dB 3dB Remote Remote Remote Remote Weatherproof Weatherproof Weatherproof Weatherproof Antenna Antenna Antenna Antenna Installation Guide General 7845GSM and 7845i-GSM Communication Modules both come equipped with internal dual band cellular antennas. In most cases, this antenna will provide a sufficient received signal strength indication (RSSI) for a successful installation. The Honeywell GSM-ANT3dB Remote Weatherproof Antenna should be used in installations where the antenna must be mounted outdoors at some distance from the radio and gain is needed. Signal Strength For reliable service, 7845GSM and 7845i-GSM should only be installed in locations where the RSSI is a minimum of three bars. RSSI is a measure of how well the 7845GSM is receiving the cell tower. The RSSI value measured in dBm can be viewed using the 7720P Programming Tool, by using the shift command. dBm is displayed as a negative value on the 7720P and a lower negative number is better. i.e.: -60 dBm is a better RSSI than -100 dBm. Installation Guidelines By following a few simple guidelines, you can maximize the performance of 7845GSM / 7845i-GSM using the internal antenna and simplify your installation. • Find the best coverage before mounting and wiring into the radio by moving 7845GSM to several locations while monitoring the RSSI. • The best RSSI can usually be found at the highest point in the building on an exterior wall. Avoid the basement. • Maintain at least 12 inches of clearance between 7845GSM and steel I-beams, HVAC ducts, metal studs, steel roofs, exterior walls with metalized insulation or aluminum siding and other large metal objects. If a consistent RSSI of three bars cannot be found with the internal antenna, an external antenna should be used. External Antenna The GSM-ANT3dB is an exterior weatherproof antenna that can be mounted up to 50 feet away from the radio when the proper coax cable is used. Refer to Table 1 for coax cable selection. Install the GSM-ANT3dB as follows: 1. Measure and record the 7845GSM RSSI using the internal antenna for reference. 2. Disconnect all power from the unit including the battery. 3. Remove plastic plug from the SMA mounting hole on top of the 7845GSM and insert the SMA end of the adapter cable. Secure the SMA connector with the included washer and nut. 4. Plug the MMCX end of the adapter cable into the external antenna port and route cable as shown. 5. Attach the antenna and ground plane to the mounting bracket as shown in Figure 1. 6. Find a suitable location so that the antenna will be mounted vertically: • The best antenna location is usually at the highest point within the building. Avoid the basement. • Maintain at least 12 inches of clearance between the antenna and large metal objects. 7. Route the coax cable and make all required connections. 8. Restore power to the unit, measure the RSSI and compare the new value to the value recorded in Step 1. 9. Adjust the location of the antenna if needed to maximize the RSSI, for at least three bars. 10. Permanently mount the antenna vertically using the hardware as shown. The included silicon rubber tape is used to waterproof the antenna connection